Critical assessment of various techniques for the extraction of carotenoids and co-enzyme Q10 from the Thraustochytrid strain ONC-T18

A variety of techniques for extracting carotenoids from the marine Thraustochytrium sp. ONC-T18 was compared. Specifically, the organic solvents acetone, ethyl acetate, and petroleum ether were tested, along with direct and indirect ultrasonic assisted extraction (probe vs bath) methods. Techniques that used petroleum ether/acetone/water (15:75:10, v/v/v) with 3 h of agitation, or 5 min in an ultrasonic bath, produced the highest extraction yields of total carotenoids (29−30.5 μg g^-1). Concentrations up to 11.5 μg g^-1 of canthaxanthin and 17.5 μg g^-1 of β-carotene were detected in extracts stored for 6 weeks. Astaxanthin and echinenone were also detected as minor compounds. Extracts with and without antioxidants showed similar carotenoid concentration profiles. However, total carotenoid concentrations were approximately 8% higher when antioxidants were used. Finally, an easy-to-perform and inexpensive method to detect co-enzymes in ONC-T18 was also developed using silica gel TLC plates. Five percent methanol in toluene as a mobile phase consistently eluted co-enzyme Q10 standards and could separate the co-enzyme fractions present in ONC-T18.

Evaluation of fatty acid extraction methods for Thraustochytrium sp. ONC-T18

Various extraction methods were assessed in their capacity to extract fatty acids from a dried biomass of Thraustochytrium sp. ONC-T18. Direct saponification using KOH in ethanol or in hexane:ethanol was one of the most efficient techniques to extract lipids (697 mg g^-1). The highest amount of fatty acids (714 mg g^-1) was extracted using a miniaturized Bligh and Dyer extraction technique. The use of ultrasonics to break down cell walls while extracting with solvents (methanol:chloroform) also offered high extraction yields of fatty acids (609 mg g^-1). Moreover, when the transesterification mixture used for a direct transesterification method was doubled, the extraction of fatty acids increased approximately 77% (from 392 to 696 mg g^-1). This work showed that Thraustochytrium sp. ONC-T18 has the ability to produce over 700 mg g^-1 of lipids, including more than 165 mg g-1 of docosahexaenoic acid, which makes this microorganism a potential candidate for the commercial production of polyunsaturated fatty acids. Finally, other lipids, such as myristic, palmitic, palmitoleic, and oleic acids, were also produced and recovered in significant amounts (54, 196, 123, and 81 mg g^-1), respectively.

Feature extraction for animal fiber identification

Fiber identification has been a very important task in many industries such as wool growing, textile processing, archaeology, histochernical engineering, and zoology. Over the years, animal fibers have been identified using physical and chemical approaches. Recently, objective identification of animal fibers has been developed based on the cuticular information of fibers. Effective and accurate extraction of representative features is essential to animal fiber identification and classification. In the current work, two different strategies are developed for this purpose. In the first method, explicit features are extracted using image processing. However, only implicit features are used in the second method with an unsupervised artificial neural network. It is found that the use of explicit features increases the accuracy of fiber identification but requires more effort on processing images and solid knowledge of what features are representative ones.

Extraction of copper(II) ions from aqueous solutions with a methimazole-based ionic liquid

The recently synthesized ionic liquid (IL) 2-butylthiolonium bis(trifluoromethanesulfonyl)amide, [mimSBu][NTf2], has been used for the extraction of copper(II) from aqueous solution. The pH of the aqueous phase decreases upon addition of [mimSBu]+, which is attributed to partial release of the hydrogen attached to the N(3) nitrogen atom of the imidazolium ring. The presence of sparingly soluble water in [mimSBu][NTf2] also is required in solvent extraction studies to promote the incorporation of Cu(II) into the [mimSBu][NTf2] ionic liquid phase. The labile copper(II) system formed by interacting with both the water and the IL cation component has been characterized by cyclic voltammetry as well as UV−vis, Raman, and 1H, 13C, and 15N NMR spectroscopies. The extraction process does not require the addition of a complexing agent or pH control of the aqueous phase. [mimSBu][NTf2] can be recovered from the labile copper−water−IL interacting system by washing with a strong acid. High selectivity of copper(II) extraction is achieved relative to that of other divalent cobalt(II), iron(II), and nickel(II) transition-metal cations. The course of microextraction of Cu2+ from aqueous media into the [mimSBu][NTf2] IL phase was monitored in situ by cyclic voltammetry using a well-defined process in which specific interaction with copper is believed to switch from the ionic liquid cation component, [mimSBu], to the [NTf2] anion during the course of electrochemical reduction from Cu(II) to Cu(I). The microextraction−voltammetry technique provides a fast and convenient method to determine whether an IL is able to extract electroactive metal ions from an aqueous solution.

Cloud-point extraction of phenanthrene by nonionic surfactants

Extraction and preconcentration of the model polycyclic aromatic hydrocarbon (PAH), phenanthrene, in aqueous solutions by two different kinds of nonionic ethoxylated alcohols, Tergitol 15-S-7 and Neodol 25-7, as extractants was studied at ambient temperature (22°C). Both surfactants have almost the same numbers of hydrocarbons and ethylene-oxide (EO) units, but differ in the location of the alcohols. Neodol 25-7 is a primary alcohol, while Tergitol 15-S-7 is a secondary one. The extraction process is based on the clouding phenomena of these two nonionic surfactants. Addition of sodium sulfate or sodium phosphate could decrease the cloud point temperatures of the surfactant solutions below the ambient temperatures, so that the cloud-point extraction process could be facilitated. Increasing the salt concentration or decreasing the surfactant concentration could improve the preconcentration factor, which is attributable to the decrease in the volume of surfactant-rich phase. Consequently, the recovery efficiency higher than 96% was achieved for phenanthrene in aqueous solution.

A novel cloud-point extraction process for preconcentrating selected polycyclic aromatic hydrocarbons in aqueous solution

A novel but simple cloud-point extraction (CPE) process is developed to preconcentrate the trace of selected polycyclic aromatic hydrocarbons (PAHs) with the use of the readily biodegradable nonionic surfactant Tergitol 15-S-7 as extractant. The concentrations of PAHs, mixtures of naphthalene and phenanthrene as well as pyrene, in the spiked samples were determined with the new CPE process at ambient temperature (23 °C) followed by high performance liquid chromatography (HPLC) with fluorescence detection. More than 80% of phenanthrene and pyrene, respectively, and 96% of naphthalene initially present in the aqueous solutions with concentrations near or below their aqueous solubilities were recovered using this new CPE process. Importantly Tergitol 15-S-7 does not give any fluorometric signal to interfere with fluorescence detection of PAHs in the UV range. No special washing step is, thus, required to remove surfactant before HPLC analyses. Different experimental conditions were studied. The optimum conditions for the preconcentration and determi nation of these selected PAHs at ambient temperature have been established as the following:  (1) 3 wt % surfactant; (2) addition of 0.5 M Na2SO4; (3) 10 min for equilibration time; and (4) 3000 rpm for centrifugal speed with duration of 10 min.

General synthesis of two-dimensional patterned conducting polymer-nanobowl sheet via chemical polymerization

A general method for the generation of two-dimensional (2D) ordered, large-area, and liftable conducting polymer-nanobowl sheet has been demonstrated via chemical polymerization for the first time. The sheet is made using the monolayer self-assembled from polystyrene (PS) spheres at the aqueous/air interface as template, followed by depositing conducting polymer on the part of PS monolayer submerging in the aqueous phase via chemical polymerization, and core extraction. During the process of polymerization, no substrate is required, which caused the as-prepared patterned conducting polymer sheet can be easily lifted-off and deposited, in full size, on any flat substrate. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Fourier transform infrared (FTIR) spectrum were used to characterize the products