Cold rolling mill thickness control using the cascade-correlation neural network

The improvements in thickness accuracy of a steel strip produced by a tandem cold-roIling mill are of substantial interest to the steel industry. In this paper, we designed a direct model-reference adaptive control (MRAC)  scheme that exploits the natural level of excitation existing in the closed-loop with a dynamically constructed cascade-correlation neural network (CCNN) as a controller for cold roIling mill thickness control. Simulation results show that the combination of a such a direct MRAC scheme and the dynamically constructed CCNN significantly improves the thickness accuracy in the presence of disturbances and noise in comparison with to the conventional PID controllers.

Microstructural evolution of ultrafine grained structure in plain carbon steels through single pass rolling

In the present study, the effect of nominal equivalent strain (between 0 and 1.2), deformation temperature (790– 750°C) and carbon content (0.06 – 0.35%C) was investigated on ferrite grain refinement through dynamic strain induced transformation (DSIT) in plain carbon steels in single pass rolling. The microstructural evolution of the transformation of austenite to ferrite has been evaluated through the thickness of the strip. The results showed a number of important microstructural features as a function of strain, which could be classified into three regions; no DSIT region, DSIT region, and ultrafine ferrite (UFF) grain region. Hence, two critical strains; dynamic strain induced transformation (εC, DSIT) and ultrafine ferrite formation (εC, UFF) were determined. These strains were increased significantly with an increase in carbon content. The critical strain for UFF formation reduced with decrease in deformation temperature. The UFF microstructure consisted of ultrafine, equiaxed ferrite grains (<2 μm) with very fine cementite particles. In the centre of the rolled strip, there was a conventional ferrite– pearlite microstructure, although ferrite grain refinement and the volume fraction of ferrite increased with increase in the nominal equivalent strain.

Formation of ultrafine grained microstructures in steel through strain induced transformation during single pass hot rolling

In the present study, wedge-shape samples were used to study the effect of strain induced transformation on the formation of ultrafine grained structures in steel by single pass rolling. The results showed two different transition strains for bainite formation and ultrafine ferrite (UFF) formation in the surface layer of strip at reductions of 40% and 70%, respectively, in a plain carbon steel. The bainitic microstructure formed by strain induced bainitic transformation during single pass rolling was also very fine. The evolution of UFF formation in the surface layer showed that ferrite coarsening is significantly reduced through strain induced transformation combined with rapid cooling in comparison with the centre of the strip. In the surface, the ferrite coarsening mostly occurred for intragranular nucleated grains (IG) rather than grain boundary (GB) ferrite grains. The results suggest that normal grain growth occurred during overall transformation in the GB ferrite grains. In the centre of the strip, there was significantly more coarsening of ferrite grains nucleated on the prior austenite grain boundaries.

Predicting the rolling force in hot steel rolling mill using an ensemble model

Accurate prediction of the roll separating force is critical to assuring the quality of the final product in steel manufacturing. This paper presents an ensemble model that addresses these concerns. A stacked generalisation approach to ensemble modeling is used with two sets of the ensemble model members, the first set being learnt from the current input-output data of the hot rolling finishing mill, while another uses the available information on the previous coil in addition to the current information. Both sets of ensemble members include linear regression, multilayer perceptron, and k-nearest neighbor algorithms. A competitive selection model (multilayer perceptron) is then used to select the output from one of the ensemble members to be the final output of the ensemble model. The ensemble model created by such a stacked generalization is able to achieve extremely high accuracy in predicting the roll separation force with the average relative accuracy being within 1% of the actual measured roll force.

Antecedents of brand credibility under asymmetrical information

This study focuses on the antecedents of brand credibility and validates part of the model presented by Erdem and Swait (1998). Following the signalling literature, we argue that under asymmetrical information, the importance of brand credibility stems from the capability of brands to inform consumers who are uncertain about product attributes. Indeed, firms may use brands to notify consumers about product positions and to assure that their product claims are credible. Using information economics as theoretical background, the proposed perspective determines how credibility is shaped. Data was collected across a number of consumers in Australia via a self-report survey and a structural equation model (SEM) was estimated. The results provide empirical evidence and support the work of Erdem and Swait (1998).

Nucleation sites for ultrafine ferrite produced by deformation of austenite during single-pass strip rolling

An austenitic Ni-30 wt pct Fe alloy, with a stacking-fault energy and deformation characteristics similar to those of austenitic low-carbon steel at elevated temperatures, has been used to examine the defect substructure within austenite deformed by single-pass strip rolling and to identify those features most likely to provide sites for intragranular nucleation of ultrafine ferrite in steels. Samples of this alloy and a 0.095 wt pct C-1.58Mn-0.22Si-0.27Mo steel have been hot rolled and cooled under similar conditions, and the resulting microstructures were compared using transmission electron microscopy (TEM), electron diffraction, and X-ray diffraction. Following a single rolling pass of ∼40 pct reduction of a 2mm strip at 800 °C, three microstructural zones were identified throughout its thickness. The surface zone (of 0.1 to 0.4 mm in depth) within the steel comprised a uniform microstructure of ultrafine ferrite, while the equivalent zone of a Ni-30Fe alloy contained a network of dislocation cells, with an average diameter of 0.5 to 1.0 µm. The scale and distribution and, thus, nucleation density of the ferrite grains formed in the steel were consistent with the formation of individual ferrite nuclei on cell boundaries within the austenite. In the transition zone, 0.3 to 0.5 mm below the surface of the steel strip, discrete polygonal ferrite grains were observed to form in parallel, and closely spaced “rafts” traversing individual grains of austenite. Based on observations of the equivalent zone of the rolled Ni-30Fe alloy, the ferrite distribution could be correlated with planar defects in the form of intragranular microshear bands formed within the deformed austenite during rolling. Within the central zone of the steel strip, a bainitic microstructure, typical of that observed after conventional hot rolling of this steel, was observed following air cooling. In this region of the rolled Ni-30Fe alloy, a network of microbands was observed, typical of material deformed under plane-strain conditions.

Asymmetrical three-DOFs rotational-translational parallel-kinematics mechanisms based on lie group theory

The paper introduces four families of three-DOFs translational-rotational Parallel-Kinematics Mechanisms (PKMs) as well as the mobility analysis of such families using Lie group theory. Two of these families are mechanisms with one-rotational two-translational degrees of freedom (DOFs) and each of the other two has one-translational two-rotational DOFs. Four novel mechanisms are presented and discussed as representatives of these four families. Although these mechanisms are asymmetric, the components used to realise them are very similar and, hence, there is no great departure from the favourable modularity of parallel-kinematics mechanisms.

Numerical investigation of austenite grain size distribution in square-diamond pass hot bar rolling

In this study, the austenite grain size (AGS) for hot bar rolling of AISI4135 steel was predicted based on two different AGS evolution models available in the literature. In order to predict the AGS more accurately, both models were integrated with a three-dimensional non-isothermal finite element program by implementing a modified additivity rule. The predicted results based on two models for the square-diamond (S-D) and round-oval (R-O) pass bar rolling processes were compared with the experimental data available in the literature. Then, numerical predictions depending on various process parameters such as interpass time, temperature, and roll speed were made to compare both models and investigate the effect of these parameters on the AGS distributions. Such numerical results were found to be beneficial to understand the effect of the microstructure evolution model on the rolling processes better and control the processes more accurately.

Analytical model of pass-by-pass strain in rod (or bar) rolling and its applications to prediction of austenite grain size

Rod rolling is a process where the deformation state of the workpiece between the work rolls is quite different from the strip rolling process. However, in most microstructure evolution models, the simple area strains (natural logarithm of the area reduction ratio) multiplied by a constant have been used to compute pass-by-pass evolution of austenite grain size (AGS) in rod (or bar) rolling, without any verification. The strains at a given pass play a crucial role in determining the recrystallization behavior (static or dynamic). In this study, an analytical model that calculates the pass-by-pass strain and strain rate in rod rolling has been developed and verified by conducting four-pass (oval–round) bar and plate rolling experiments. Numerical simulations have then been carried out for the four-pass rolling sequence using the area strain model and the new analytical model, focusing on the effect of the method for calculating the strain on the recrystallization behavior and evolution of AGS. The AGS predicted was compared with those obtained from hot torsion tests. It is shown that the analytical model developed in this study is more appropriate in the analysis of bar (or rod) rolling. It was found that the recrystallization behavior and evolution of AGS during this process were influenced significantly by the calculation method for the deformation parameters (strain and strain rate). The pass-by-pass strain obtained from the simple area strain model is inadequate to be used as an input to the equations for recrystallization and AGS evolution under these rolling conditions.

Integrated model for thermo-mechanical controlled process in rod (or bar) rolling

This study presents an integrated model for computing the thermo-mechanical parameters (cross-sectional shape of workpiece, the pass-by-pass strain and strain rate and the temperature variation during rolling and cooling between inter-stands) and metallurgical parameters (recrystallisation behaviour and austenite grain size—AGS), to assess the potential for developing “Thermo-Mechanical Controlled Process” technology in rod (or bar) rolling, which has been a well-known technical terminology in strip (or plate) rolling since 1970s.

The advantage of this model is that metallurgical and mechanical parameters are obtained simultaneously in a short computation time compared with other models. The model has been applied to a rod mill to predict the exit cross-sectional shape, area and AGS per pass by incorporating the equations for AGS evolution being used in strip rolling. At the finishing train of rod mills, the strain rates reach as high as 1000–3000 s−1 and the inter-pass times are around 10–60 ms.

The results show that the proposed model is an efficient tool for evaluating the effects of process-related parameters on product quality and dimensional tolerance of the products in rod (or bar) rolling. The results of the simulation demonstrated that the equation for AGS evolution being used in strip rolling might have limitations when applied directly to rod rolling at a high strain rate.

A comparative study of microstructures and mechanical properties obtained by bar and plate rolling

Microstructures and mechanical properties of a low carbon steel were studied after plate rolling and bar rolling. Plate rolling is characterized as a monotonic compressive loading, while bar rolling is characterized as a cross-compressive loading. A four-pass plate rolling and bar rolling experiment was designed so that the material experiences the same amount of strain at each pass during rolling. The rolling experiment was performed at moderately high temperatures (450, 550 and 650 °C). The microstructures and mechanical properties of the low carbon steel acquired from the two types of rolling experiments were compared. The results revealed that differences of loading path attributed by monotonic loading (plate rolling) and cross loading (bar rolling) significantly influenced the microstructures and mechanical properties such as yield stress, ultimate tensile stress, strain hardening exponent and elongation of the low carbon steel.