Modification of thermoplastic coatings for improved cathodic disbondment performance on a steel substrate : a study on failure mechanisms

The effect of blending two different materials with a medium density polyethylene for use as pipe coatings is presented. The influence of such blending on properties such as cathodic disbondment (CD) and wet adhesion on steel is investigated. The components blended include a functionalised polyethylene (PE) containing the polar functionality, maleic anhydride (MAH) and an amorphous elastomer, ethylene-propylene-diene terpolymer (EPDM). It was found that modification of PE with small amount (2.5–3 wt%) of either blended MAH-g-PE or EPDM resulted in a significant improvement in CD performance and wet adhesion strength. The mode of failure and disbondment mechanism was investigated using energy dispersive X-ray spectroscopy (EDXS) and X-ray photoelectron spectroscopy (XPS). The greater resistance of migration of sodium ions increases with the incorporation of the modifiers, and it is proposed that this results in an increase in CD performance.

Comparative study on MoO3 and HxMoO3 nanobelts : structure and electric transport

In this study, the suspension of MoO3 nanobelts was first prepared in a hydrothermal way from Mo powders and H2O2 solution, which could be transformed into the suspension of HxMoO3 nanobelts under an acidic condition using N2H4 ·H2O as the reducing agent. Three paper-form samples made from MoO3 and HxMoO3 nanobelts (low or high hydrogen content) were then fabricated via a vacuum filtration method, followed by their structural comparative analysis such as FESEM, XRD, Raman spectra, and XPS, etc. The measurement of electric resistances at room temperature shows that the conductance of HxMoO3 nanobelts is greatly improved because of hydrogen doping. The temperature-dependent resistances of HxMoO3 nanobelts agree with the exponential correlation, supporting that the conducting carriers are the quasi-free electrons released from Mo5+. In addition, the formation process of HxMoO3 nanobelts from MoO3 nanobelts is also discussed.

Study on nanocellulose by high pressure homogenization in homogeneous isolation

Nanocellulose from cotton cellulose was prepared by high pressure homogenization (HPH) in ionic liquids (1-butyl-3-methylimidazolium chloride ([Bmim]Cl). The nanocellulose possessed narrow particle size distribution, with diameter range of 10–20 nm. Weight average molecular weight (Mw) of nanocellulose treated by HPH was lower (173.8 kDa) than the one ILs treated cellulose (344.6 kDa). X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT-IR), and Solid-state CP/MAS 13C NMR measurements were employed to study the mechanism of structural changes, which suggested that network structure between cellulose chains were destructed by the shearing forces of HPH in combination with ionic liquids. The intermolecular and intra-molecular hydrogen bonds of cellulose were further destroyed, leading to the long cellulose molecular chains being collapsed into short chains. Therefore, the nanocellulose could provide desired properties, such as lower thermal stability and strong water holding capacity. Results indicated that it had great potential in the applications for packaging, medicines, cosmetics and tissue engineering.

A systematic study of carbon fibre surface grafting via in situ diazonium generation for improved interfacial shear strength in epoxy matrix composites

A recently established means of surface functionalization of unsized carbon fibres for enhanced compatibility with epoxy resins was optimised and evaluated using interfacial shear stress measurements. Interfacial adhesion has a strong influence on the bulk mechanical properties of composite materials. In this work we report on the optimisation of our aryl diazo-grafting methodology via a series of reagent concentration studies. The fibres functionalised at each concentration are characterised physically (tensile strength, modulus, coefficient of friction, and via AFM), and chemically (XPS). The interfacial shear strength (IFSS) of all treated fibres was determined via the single fibre fragmentation test, using the Kelly-Tyson model. Large increases in IFSS for all concentrations (28-47%) relative to control fibres were observed. We show that halving the reagent concentration increased the coefficient of friction of the fibre and the interfacial shear strength of the composite while resulting in no loss of the key performance characteristics in the treated fibre.