Design and simulation of a low voltage wide band RF MEMS switch

This paper presents design of an electrostatic wide band shunt capacitive coupling RF MEMS switch with low actuation voltage. The key factors of the RF MEMS switch design are the proper scattering parameters, low actuation voltage, and the cost of the fabrication process. An overview of the recent low actuation voltage RFMEMS switches has been presented. These designs still suffer from the complexity of process, lack of reliability, limitation of frequency band, and process cost. RF characteristics of a shunt RF MEMS switches are specified mostly by coupling capacitor in upstate position of the membrane Cu. This capacitor is in trade-off with actuation voltage. In this work, the capacitor is eliminated by using two short high impedance transmission lines, at the input and output of the switch. The simulation results demonstrate an improvement in the RF characteristic of the switch.

Design and simulation of a high isolation RF MEMS shunt capacitive switch for C-K band

This paper presents a wide band RF MEMS capacitive switch. The LC resonant frequency is reduced from mm wave to X band frequencies at down-state by using a meander type membrane, with the frequency band is being increased by adding two short high impedance lines at both ends of coplanar waveguide (CPW). Moreover, this acts as T-match circuit in up-state position and improves the matching. Simulation results demonstrate that the capacitance ratio reduces from 50 to 21.4, S21 and S11 are less than −10dB for the entire frequency band at down-state and up-state. Also, a comprehensive and complete electric model of the switch is proposed and simulation results agree well with the characteristics of the physical structure of the MEMS switch. Vpull-in and Vpull-out of this switch are 8.1V and 0.3V, respectively.

Photocatalytic reduction of carbon dioxide

Carbon dioxide reforming happens all the time in nature by photosynthesis of plants. It thus provides a great challenge to equal or surpass this photosynthesis in an artificial system. This paper presents a literature review of using semi-conductor to assist photocatalytic reduction of carbon dioxide under UV irradiation. It analyses some key factors influencing the reaction rates which have been studied worldwide in respective areas. Special interest is taken in recommending possible improvements for the heterogeneous photocatalysis involving gas-solid interfaces, particularly in relation to the influencing factors affecting product concentrations and the reduction rate.

Light emission and excitonic effect of boron nitride nanotubes observed by photoluminescent spectra

Photoluminescent (PL) and optical absorption spectra of high-yield multi-wall BN nanotubes (BNNTs) were systematically investigated at room temperature in comparison with commercial hexagonal BN (h-BN) powder. The direct band gap of the BNNTs was determined to be 5.75 eV, just slightly narrower than that of h-BN powder (5.82 eV). Two Frenkel excitons with the binding energy of 1.27 and 1.35 eV were also determined. However, they were not a distinctive characteristic of the BNNTs as reported previously. Observed broad UV–visible–NIR light emission demonstrates the potential of the BNNTs as a nano light source.

Donor-п-acceptor conjugated copolymers for photovoltaic applications : tuning the open-circuit voltage by adjusting the donor/acceptor ratio

A class of new conjugated copolymers containing a donor (thiophene)−acceptor (2-pyran-4-ylidene-malononitrile) was synthesized via Stille coupling polymerization. The resulting copolymers were characterized by 1H NMR, elemental analysis, GPC, TGA, and DSC. UV−vis spectra indicated that the increase in the content of the thiophene units increased the interaction between the polymer main chains to cause a red-shift in the optical absorbance. Cyclic voltammetry was used to estimate the energy levels of the lowest unoccupied molecular orbital (LUMO) and the highest occupied molecular orbital (HOMO) and the band gap (Eg) of the copolymers. The basic electronic structures of the copolymers were also studied by DFT calculations with the GGA/B3LYP function. Both the experimental and the calculated results indicated an increase in the HOMO energy level with increasing the content of thiophene units, whereas the corresponding change in the LUMO energy level was much smaller. Polymer photovoltaic cells of a bulk heterojunction were fabricated with the structure of ITO/PEDOT/PSS (30 nm)/copolymer−PCBM blend (70 nm)/Ca (8 nm)/Al (140 nm). It was found that the open-circuit voltage (Voc) increased (up to 0.93 V) with a decrease in the content of thiophene units. Although the observed power convention efficiency is still relatively low (up to 0.9%), the corresponding low fill factor (0.29) indicates considerable room for further improvement in the device performance. These results provided a novel concept for developing high Voc photovoltaic cells based on donor-π-acceptor conjugated copolymers by adjusting the donor/acceptor ratio.

Pi-shaped MEMS architecture for lowering actuation voltage of RF switching

A wide band low actuation capacitive coupling electrostatic RF MEMS switching device is presented in this paper. The device includes a pi-shaped matching architecture containing two switches connected by a high impedance short transmission line. The device can act as a switch for any desired frequency whilst requiring only 12volts for actuation. By optimizing the length and the characteristic impedance of the transmission line, the switch can be tailored for desired frequency bands. The switch is calculated and simulated for Ka to V frequency bands demonstrating excellent improvements of RF characteristics.

C-BN single-walled nanotubes from hybrid connection of BN/C nanoribbons : prediction by ab initio density functional calculations

We demonstrated for the first time by ab initio density functional calculation and molecular dynamics simulation that C0.5(BN)0.5 armchair single-walled nanotubes (NT) are gapless semiconductors and can be spontaneously formed via the hybrid connection of graphene/BN Nanoribbons (GNR/BNNR) at room temperature. The direct synthesis of armchair C0.5(BN)0.5 via the hybrid connection of GNR/BNNR is predicted to be both thermodynamically and dynamically stable. Such novel armchair C0.5(BN)0.5 NTs possess enhanced conductance as that observed in GNRs. Additionally, the zigzag C0.5(BN)0.5 SWNTs are narrow band gap semiconductors, which may have potential application for light emission. In light of recent experimental progress and the enhanced degree of control in the synthesis of GNRs and BNNR, our results highlight an interesting avenue for synthesizing a novel specific type of C0.5(BN)0.5 nanotube (gapless or narrow direct gap semiconductor), with potentially important applications in BNC-based nanodevices.

Incorporation of fused tetrathiafulvalenes (TTFs) into polythiophene architectures : varying the electroactive dominance of the TTF species in hybrid systems

A novel polythienylenevinylene (PTV) and two new polythiophenes (PTs), featuring fused tetrathiafulvalene (TTF) units, have been prepared and characterized by ultraviolet−visible (UV−vis) and electron paramagnetic resonance (EPR) spectroelectrochemistry. All polymers undergo two sequential, reversible oxidation processes in solution. Structures in which the TTF species is directly linked to the polymer backbone (2 and 4) display redox behavior which is dictated by the fulvalene system. Once the TTF is spatially removed from the polymer chain by a nonconjugated link (polymer 3), the electroactivity of both TTF and polythiophene moieties can be detected. Computational studies confirm the delocalization of charge over both electroactive centers (TTF and PT) and the existence of a triplet dication intermediate. PTV 4 has a low band gap (1.44 eV), is soluble in common organic solvents, and is stable under ambient conditions. Organic solar cells of polymer 4:[6,6]-phenyl-C₆₁ butyric acid methyl ester (PCBM) have been fabricated. Under illumination, a photovoltaic effect is observed with a power conversion efficiency of 0.13% under AM1.5 solar simulated light. The onset of photocurrent at 850 nm is consistent with the onset of the π−π absorption band of the polymer. Remarkably, UV−vis spectroelectrochemistry of polymer 4 reveals that the conjugated polymer chain remains unchanged during the oxidation of the polymer.

Large-scale synthesis and growth mechanism of single-crystal Se nanobelts

Single-crystal trigonal (t) Se nanobelts have been synthesized on a large scale by reducing SeO2 with glucose at 160 °C. Electron microscopy images show that the nanobelts are 80 nm in diameter, 25 nm in thickness, and up to several hundreds of micrometers in length. HRTEM images prove that the nanobelts are single crystals and preferentially grow along the [001] direction. The time-dependent TEM images revealed that the formation and growth of t-Se nanobelts were governed by a solid−solution−solid growth mechanism. The redox reaction directly produced amorphous (α) Se nanoparticles under hydrothermal conditions. t-Se nanobelts were formed by dissolution and recrystallization of the initial α-Se nanoparticles under the functional capping of poly(vinylpyrrolidone) (PVP). The nanobelts obtained exhibit a quantum size effect in optical properties, showing a blue shift of the band gap and direct transitions relative to the values of bulk t-Se.

Emerging wireless personal area networks(WPANs) : - An analysis of techniques, tools and threats

Wireless Personal Area Networks provide a pivotal role in local area network technology complementing traditional Wireless Local Area Network technologies. Bluetooth, ZigBee and NFC (Near Field Communications) have emerged as key WPAN technologies with UWB (Ultra Wide Band) standards currently evolving. They are however subject to the usual range of security vulnerabilities found in wireless LANs such as spoofing, snooping, man-in-the-middle, denial of service and other attacks. However security in WPANs is not as mature as it is in Wireless LANs and further work is needed in order to provide comparable protection. This paper examines a range of WPAN technologies and security issues and proposes protection mechanisms that can mitigate risk in each case. © 2012 IEEE.

Fabrication and visible-light photocatalytic behavior of perovskite praseodymium ferrite porous nanotubes

Perovskite praseodymium ferrite (PrFeO3) porous nanotubes are prepared by electrospinning of the precursor solution into nanofibers, subsequently by annealing the precursor fibers at a low temperature (e.g. 40 °C) and finally by calcination at a high temperature. The low temperature annealing treatment is found to play a key role in the formation of porous nanotube. The porous tubes show a perovskite-type PrFeO3 crystal characteristic with high optical absorption in the UV-visible region and an energy band gap of 1.97 eV. When compared with PrFeO3 porous nanofibers and PrFeO3 particles, the PrFeO3 porous nanotubes show better visible-light photo-catalytic ability to degrade Rhodamine B in aqueous phase because of the increased surface area and more active catalytic sites on the inner walls and outer surfaces.

Comparison of various NMR methods for the indirect detection of nitrogen-14 nuclei via protons in solids

We present an experimental comparison of several through-space Hetero-nuclear Multiple-Quantum Correlation experiments, which allow the indirect observation of homo-nuclear single- (SQ) or double-quantum (DQ) ¹⁴N coherences via spy ¹H nuclei. These ¹H-{¹⁴N} D-HMQC sequences differ not only by the order of ¹⁴N coherences evolving during the indirect evolution, t1, but also by the radio-frequency (rf) scheme used to excite and reconvert these coherences under Magic-Angle Spinning (MAS). Here, the SQ coherences are created by the application of center-band frequency-selective pulses, i.e. long and low-power rectangular pulses at the ¹⁴N Larmor frequency, ν0(¹⁴N), whereas the DQ coherences are excited and reconverted using rf irradiation either at ν0(¹⁴N) or at the ¹⁴N overtone frequency, 2ν0(¹⁴N). The overtone excitation is achieved either by constant frequency rectangular pulses or by frequency-swept pulses, specifically Wide-band, Uniform-Rate, and Smooth-Truncation (WURST) pulse shapes. The present article compares the performances of four different ¹H-{¹⁴N} D-HMQC sequences, including those with ¹⁴N rectangular pulses at ν0(¹⁴N) for the indirect detection of homo-nuclear (i) ¹⁴N SQ or (ii) DQ coherences, as well as their overtone variants using (iii) rectangular or (iv) WURST pulses. The compared properties include: (i) the sensitivity, (ii) the spectral resolution in the ¹⁴N dimension, (iii) the rf requirements (power and pulse length), as well as the robustness to (iv) rf offset and (v) MAS frequency instabilities. Such experimental comparisons are carried out for γ-glycine and l-histidine.HCl monohydrate, which contain ¹⁴N sites subject to moderate quadrupole interactions. We demonstrate that the optimum choice of the ¹H-{¹⁴N} D-HMQC method depends on the experimental goal. When the sensitivity and/or the robustness to offset are the major concerns, the D-HMQC sequence allowing the indirect detection of ¹⁴N SQ coherences should be employed. Conversely, when the highest resolution and/or adjusted indirect spectral width are needed, overtone experiments are the method of choice. The overtone scheme using WURST pulses results in broader excitation bandwidths than that using rectangular pulses, at the expense of reduced sensitivity. Numerically exact simulations also show that the sensitivity of the overtone ¹H-{¹⁴N} D-HMQC experiment increases for larger quadrupole interactions.

Investigation of the potential of plasma technology to improve the performance of solar cells

 This study explored plasma techniques to improve the efficiency of dye sensitised solar cells and perovskite solar cells. It was found that plasma functionalization of TiO2 improved dye absorption, thereby improving efficiency. Controllable nitrogen doping of TiO2 was achieved by a unique system that combines plasma with heat treatment. The doping reduced the band-gap of TiO2. A crystalline TiO2 thin film on plastic substrates was successfully achieved by a low temperature plasma method, which could potentially allow such soft and flexible substrates to be used for solar cells.