Near-surface distributions of soil water and water repellency under three effluent irrigation schemes in a blue gum (Eucalyptus globulus) plantation

Water repellent soils are difficult to irrigate and susceptible to preferential flow, which enhances the potential for accelerated leaching to groundwater of hazardous substances. Over 5 Mha of Australian soil is water repellent, while treated municipal sewage is increasingly used for irrigation. Only if a critical water content is exceeded will repellent soils become wettable. To avoid excessive loss of water from the root zone via preferential flow paths, irrigation schemes should therefore aim to keep the soil wet enough to maintain soil wettability. Our objective was to monitor the near-surface water content and water repellency in a blue gum (Eucalyptus globulus) plantation irrigated with treated sewage. The plantation's sandy soil surface was strongly water repellent when dry. For 4 months, three rows of 15 blue gum trees each received no irrigation, three other rows received 50% of the estimated potential water use minus rainfall, and three more rows received 100%. During this period, 162 soil samples were obtained in three sampling rounds, and their water content (% dry mass) and degree of water repellency determined. Both high and low irrigation effectively wetted up the soil and eliminated water repellency after 2 (high) or 4 (low) months. A single-peaked distribution of water contents was observed in the soil samples, but the water repellency distribution was dichotomous, with 44% extremely water-repellent and 36% wettable. This is consistent with a threshold water content at which a soil sample changes from water repellent to wettable, with spatial variability of this threshold creating a much wider transition zone at the field scale. We characterized this transition zone by expressing the fraction of wettable samples as a function of water content, and demonstrated a way to estimate from this the wettable portion of a field from a number of water content measurements. To keep the plantation soil wettable, the water content must be maintained at a level at which a significant downward flux is likely, with the associated enhanced leaching. At water contents with negligible downward flux, the field is water repellent, and leaching through preferential flow paths is likely. Careful management is needed to resolve these conflicting requirements.

Heating effects on water repellency in Australian eucalypt forest soils and their value in estimating wildfire soil temperatures

Wildfires can induce or enhance soil water repellency under a range of vegetation communities. According to mainly USA-based laboratory studies, repellency is eliminated at a maximum soil temperature (T) of 280–400°C. Knowledge of T reached during a wildfire is important in evaluating post-fire soil physical properties, fertility and seedbed status. T is, however, notoriously difficult to ascertain retrospectively and often based on indicative observations with a large potential error. Soils under fire-prone Australian eucalypt forests tend to be water repellent when dry or moderately moist even if long unburnt. This study aims to quantify the temperature of water repellency destruction for Australian topsoil material sampled under three sites with contrasting eucalypt cover (Eucalyptus sieberi, E. ovata and E. baxteri). Soil water repellency was present prior to heating in all samples, increased during heating, but was abruptly eliminated at a specific T between 260 and 340°C. Elimination temperature varied somewhat between samples, but was found to be dependent on heating duration, with longest duration resulting in lowest elimination temperature. Results suggest that post-fire water repellency may be used as an aid in hindcasting soil temperature reached during the passage of a fire within repellency-prone environments.

Extraction of compounds associated with water repellency in sandy soils of different origin

After an initial evaluation of several solvents, the efficiency of Soxhlet extractions with isopropanol/ammonia (s.g. 0.88) (70 : 30 v : v; 24 h) in extracting compounds associated with water repellency in sandy soils was examined using a range of repellent and wettable control soils (n = 15 and 4) from Australia, Greece, Portugal, The Netherlands, and the UK. Extraction efficiency and the role of the extracts in causing soil water repellency was examined by determining extract mass, sample organic carbon content and water repellency (after drying at 20°C and 105°C) pre- and post-extraction, and amounts of aliphatic C–H removed using DRIFT, and by assessing the ability of extracts to cause repellency in acid-washed sand (AWS).

Key findings are: (i) none of organic carbon content, amount of aliphatic C–H, or amount of material extracted give any significant correlation with repellency for this diverse range of soils; (ii) sample drying at 105°C is not necessarily useful before extraction, but may provide additional information on extraction effectiveness when used after extraction; (iii) the extraction removed repellency completely from 13 of the 15 repellent samples; (iv) extracts from all repellent and wettable control soils were capable of inducing repellency in AWS. The findings suggest that compounds responsible for repellency represent only a fraction of the extract composition and that their presence does not necessarily always cause repellency.

Investigation of compounds causing water repellency in the rhizosphere of sandy soils from a wide range of locations.

Although soils are generally considered to wet readily, some are actually water repellent at the surface and in the rhizosphere. This phenomenon occurs at low to moderate moisture contents and has been reported from soils under a range of vegetation types and from many regions around the globe. Water repellency in soils can have serious environmental implications including reduced seed germination and plant growth as well as irrigation efficiency, accelerated soil erosion, and enhanced leaching of agrochemicals through preferential flow. it has been proposed that water repellency is caused by the accumulation of hydrophobic organic compounds released as root exudates, microbial byproducts or from decomposing organic matter, which are deposited on mineral or aggregate surfaces, or are present as interstitial matter, Few studies to date have attempted to isolate and characterize these compounds and their structure is therefore only poorly understood, These studies have generally focussed on only a single soil or a small range of samples, have not included non-repellent soils as a control and have not always been able to demonstrate that the substances isolated are indeed responsible for repellency formation.

This study reports on the first part (extraction procedures) of a research programme addressing these gaps in current knowledge by investigating a wide range of severely repellent and wettable ‘control’ samples from different countries, and by including assessments of extraction efficiency and ability of extracts to cause repellency. Analytical methods include DRIFT (Diffuse Reflectance Infrared Fourier Transform Spectroscopy) of soils and IR (Infrared) analysis of extracts.

Key findings are that (i) soil sample heating after extraction is valuable in assessing the effectiveness of the extraction procedure, (ii) Soxhlet extraction using isopropanol/ ammonia (70/30 v/v) was the most effective method in extracting hydrophobic compounds, while leaving the ability of extracted compounds to induce water repellency virtually unaffected, (iii) wettable control soils also contain hydrophobic substances capable of inducing water repellency, (iv) the amount of organic compounds extracted was poorly related to sample repellency, indicating that compounds responsible for repellency may only represent a small fraction of the extract, (v) differences in extraction efficiency between different samples indicate that the compounds responsible may differ generically and/or in terms of their bonding to minerals, and (vi) the combination of repellency assessments with DRIFT on soils and JR on extracts used with internal standards has considerable potential to allow quantification of CH bearing organic matter in the soil, the efficiency of extraction processes for its removal, and its significance in causing water repellency in soils.

Water repellency, near-saturated infiltration and preferential solute transport in a macroporous clay soil

Little attention has been paid to the possibility that soil water repellency could enhance non-equilibrium water flow and solute transport through macropores present in structured clay soils. In this study, we measured infiltration and solute transport in a clay soil under near-saturated conditions in both the field using tension infiltrometers and in the laboratory on undisturbed soil columns. Measurements were made on adjacent plots under grass and continuous arable cultivation. Steady-state field infiltration rates measured using water and ethanol as the infiltrating fluids demonstrated that the soil macroporosity under grass was better developed, but that much of the structural pore system was inactive due to water repellency. No water repellency was detected on the arable plot disturbed by tillage. Dye tracing showed that the conducting macroporosity was largely comprised of earthworm channels in the grassed plot and inter-aggregate voids resulting from ploughing in the arable plot. Tracer breakthrough curves measured on field-dry soil indicated rapid macropore transport in columns taken from both plots, although the degree of non-equilibrium transport appeared somewhat stronger under grass. This result, which was attributed to water repellency, was also consistent with the larger flow-weighted mean pore size found in the field infiltration experiments. It is concluded that water repellency in undisturbed structured clay soils can have significant effects on the occurrence of non-equilibrium water and solute transport in macropores.

Competitive sorption of intermixed heavy metals in water repellent soil in Southern Australia

In water repellent soil, Cr, Pb and Cu showed higher adsorption intensities than Zn, Cd and Ni did. Soil water repellency is much more widespread than formerly thought. In order to promote fertility and productivity, the irrigation of recycled water onto water repellent soil may be an applied technology to be used in some areas of Southern Australia. Therefore, heavy metals in recycled water potentially enter into the soil. The competitive sorption and retention capacity of heavy metals in soil are important to be determined, especially considering the special geochemical origin of water repellent soil that was caused by waxes on or between the soil particles. Batch equilibrium sorption experiments on Cd, Cr, Cu, Ni, Pb and Zn in their typical proportion in recycled water were conducted in water repellent soil. The sorption intensity, sorption isotherm in the experiments together showed that Cr, Pb and Cu have higher sorption intensity than those of Zn, Ni and Cd in the competitive system. The risk assessment for the application of recycled water onto water repellent soil is definitely necessary, especially for the metal cations with relatively weak sorption.

A new modelling approach to simulate preferential flow and transport in water repellent media: parameter sensitivity, and effects on crop growth and solute leaching

A modified version of the popular agrohydrological model SWAP has been used to evaluate modelling of soil water flow and crop growth at field situations in which water repellency causes preferential flow. The parameter sensitivity in such situations has been studied. Three options to model soil water flow within SWAP are described and compared: uniform flow, the classical mobile-immobile concept, and a recent concept accounting for the dynamics of finger development resulting from unstable infiltration. Data collected from a severely water-repellent affected soil located in Australia were used to compare and evaluate the usefulness of the modelling options for the agricultural management of such soils.

The study shows that an assumption of uniform flow in a water-repellent soil profile leads to an underestimation of groundwater recharge and an overestimation of plant transpiration and crop production. The new concept of modelling taking finger dynamics into account provides greater flexibility and can more accurately model the observed effects of preferential flow compared with the classical mobile–immobile concept. The parameter analysis indicates that the most important factor defining the presence and extremity of preferential flow is the critical soil water content.

Comparison of the modelling results with the Australian field data showed that without the use of a preferential flow module, the effects of the clay amendments to the soil were insufficiently reproduced in the dry matter production results. This means that the physical characteristics of the soil alone are not sufficient to explain the measured increase in production on clay amended soils. However, modelling with the module accounting for finger dynamics indicated that the preferential flow in water repellent soils that had not been treated with clay caused water stress for the crops, which would explain the decrease in production.

Transport properties of multi-layer fabric based on electrospun nanofiber mats as a breathable barrier textile material

Layered fabric systems with an electrospun nanofiber web layered onto a sandwich of woven fabric were developed toexamine the feasibility of developing breathable barrier textile materials. Some parameters of nanofiber mats, including thetime of electrospinning and the polymer solution concentration, were designed to change and barrier properties ofspecimens were compared. Air permeability, water vapor transmission, and water repellency (Bundesmann and hydrostaticpressure tests) were assessed as indications of comfort and barrier performance of different samples. These performancesof layered nanofiber fabrics were compared with a well-known water repellent breathable multi-layered fabric(Gortex).Multi-layered electrospun nanofiber mats equipped fabric (MENMEF) showed better performance in windproof propertythan Gortex fabric. Also, water vapor permeability of MENMEF was in a range of normal woven sport and work clothing.Comparisons of barrier properties of MENMEF and the currently available PTFE coated materials showed that, thoseproperties could be achieved by layered fabric systems with electrospun nanofiber mats.