The determination of the local conditions for void initiation in front of a crack tip for materials with second-phase particles

A procedure is proposed to determine, for second-phase particles near a crack tip, the maximum particle stresses at the moment of void initiation by either particle fracture or particle/matrix interface separation. A digital image analysis system is applied to perform a quantitative analysis of corresponding fracture surface regions from stereo image pairs taken in the scanning electron microscope. The fracture surface analysis is used to measure, for individual particles, the crack tip opening displacement at the moment of void initiation and the particle location with respect to the crack tip. From these data, the stress tensor at the moment of void initiation is calculated from the Hutchinson–Rice–Rosengren (HRR) field theory. The corresponding average local stresses within the particle are evaluated by a non-linear Mori–Tanaka-type approach. These stresses are compared to estimates according to the models by Argon et al. [A.S. Argon, J. Im, R. Safoglu, Metall. Trans. 6 (1975) 825] and Beremin [F.M. Beremin, Metall. Trans. 12 (1981) 723]. The procedure is demonstrated on an Al6061–10% Al2O3 metal matrix composite.

Polymeric materials with ordered nanostructures templated from hexagonal lyotropic liquid crystals

In this study, successful methods have been established to retain the ordered nanostructures in polymer materials templated from hexagonal lyotropic liquid crystals, which potentially renders broad applications as biomedical and membrane materials.

Crystal structures and textures in the hot-forged Ni-Mn-Ga shape memory alloys

Three ferromagnetic shape-memory alloys with the chemical compositions of Ni₅₃Mn₂₅Ga₂₂, Ni₄₈Mn₃₀Ga₂₂, and Ni₄₈Mn₂₅Ga₂₂Co₅ were prepared by the induction-melting and hot-forging process. The crystal structures were investigated by the neutron powder diffraction technique, showing that Ni₅₃Mn₂₅Ga₂₂ and Ni₄₈Mn₂₅Ga₂₂Co₅ have a tetragonal, 14/mmm martensitic structure at room temperature, while Ni₄₈Mn₃₀Ga₂₂ has a cubic, L2₁ austenitic structure at room temperature. The development of textures in the hot-forged samples shows the in-plane plastic flow anisotropy from the measured pole figures by means of the neutron diffraction technique. Significant texture changes were observed for the Ni₄₈Mn₂₅Ga₂₂Co₅ alloy after room temperature deformation, which is due to the deformation-induced rearrangements of martensitic variants. An excellent shape-memory effect (SME) with a recovery ratio of 74 pct was reported in this Ni₄₈Mn₂₅Ga₂₂Co₅ polycrystalline alloy after annealing above the martensitic transformation temperature, and the “shape-memory” influence also occurs in the distributions of grain orientations.

An analysis of factors influencing waste minimisation and use of recycled materials for the construction of residential buildings

Residential building construction activities, whether it is new build, repair or maintenance, consumes a large amount of natural resources. This has a negative impact on the environment in the form depleting natural resources, increasing waste production and pollution. Previous research has identified the benefits of preventing or reducing material waste, mainly in terms of the limited available space for waste disposal, and escalating costs associated with landfills, waste management and disposal and their impact on a  building company's profitability. There has however been little development internationally of innovative waste management strategies aimed at reducing the resource requirement of the construction process. The authors contend that embodied energy is a useful indicator of resource value. Using data provided by a regional high-volume residential builder in the State of Victoria, Australia, this paper identifies the various types of waste that are generated from the construction of a typical standard house. It was found that in this particular case, wasted amounts of materials were less than those found previously by others for cases in capital cities (5-10 per cent), suggesting that waste minimisation strategies are successfully being implemented. Cost and embodied energy savings from using materials with recycled content are potentially more beneficial in terms of embodied energy and resource depletion than waste minimisation strategies.

Multi equal channel angular pressing with rotational dies

The recent successful development of the equal channel angular pressing (ECAP) process in metals provides a feasible solution to produce ultra-fine or nano-grained bulk: materials with tailored material properties. However, ECAP is difficult to scale up commercially due to excessive load requirements. In this paper, a new Multi-ECAP process with die rotation is considered to obtain ultra-fine grain structured materials under a moderate deformation force. It is shown that an addition of torsion results in a reduction in the pressing force and an increase in severity of plastic deformation. An analysis using the upper bound method is found to be useful in predicting the pressing load and flow pattern of ECAP with and without rotational dies. Solutions are obtained for different inclined channel angles under different angular velocities of dies. Relative pressures are presented and some computed solutions are compared with those found by FEM simulation. The theoretical predictions of the pressing load are in good agreement with the simulation results. The amount of plastic deformation is determined by the inclined angle between the two intersecting channels, and the velocity ratio between the angular velocity of dies and the normal component of the punch velocity.

Conversion of the hot torsion test results into flow curve with multiple regimes of hardening

The method of Fields and Backofen has been commonly used to reduce the data obtained by hot torsion test into flow curves. The method, however, is most suitable for materials with monotonic strain hardening behaviour. Other methods such as Stüwe’s method, tubular specimens, differential testing and the inverse method, each suffer from similar drawbacks. It is shown in the current work that for materials with multiple regimes of hardening any method based on an assumption of constant hardening indices introduces some errors into the flow curve obtained from the hot torsion test. Therefore such methods do not enable accurate prediction of onset of recrystallisation where slow softening occurs. A new method to convert results from the hot torsion test into flow curves by taking into account the variation of constitutive parameters during deformation is presented. The method represents the torque twist data by a parametric linear least square model in which Euler and hyperbolic coefficients are used as the parameters. A closed form relationship obtained from the mathematical representation of the data is employed next for flow stress determination. Two different solution strategies, the method of normal equations and singular value decomposition, were used for parametric modelling of the data with hyperbolic basis functions. The performance of both methods is compared. Experimental data obtained by FHTTM, a flexible hot torsion test machine developed at IROST, for a C–Mn austenitic steel was used to demonstrate the method. The results were compared with those obtained using constant strain and strain rate hardening characteristics.

Properties of mechanically milled and spark plasma sintered Al–15 at.% MgB2 composite materials

Air-atomized pure aluminium powder with 15 at.% MgB₂ was mechanically milled (MMed) by using a vibrational ball mill, and MMed powders were consolidated by spark plasma sintering (SPS) to produce composite materials with high specific strength. Solid-state reactions of MMed powders have been examined by X-ray diffraction (XRD), and mechanical properties of the SPSed materials have been evaluated by hardness measurements and compression tests. Orientation images of microstructures were obtained via the electron backscatter diffraction (EBSD) technique.

The solid-state reactions in the Al–15 at.% MgB₂ composite materials occurred between the MMed powders and process control agent (PCA) after heating at 773–873 K for 24 h. The products of the solid-state reaction were a combination of AlB₂, Al₃BC and spinel MgAl₂O₄. Mechanical milling (MM) processing time and heating temperatures affect the characteristics of those intermetallic compounds. As the result of the solid-state reactions in MMed powders, a hardness increase was observed in MMed powders after heating at 573–873 K for 24 h. The full density was attained for the SPSed materials from 4 h or 8 h MMed powders in the Al–15 at.% MgB₂ composite materials under an applied pressure of 49 MPa at 873 K for 1 h. The microstructure of the SPSed materials fabricated from the MMed powders presented the bimodal aluminium matrix grain structure with the randomly distributions. The Al–15 at.% MgB₂SPSed material from powder MMed for 8 h exhibited the highest compressive 0.2% proof strength of 846 MPa at room temperature.

Highly fluorescent TPA-PBPV nanofibers with amplified sensory response to TNT

Well-aligned nanofibers were prepared from a conjugated polymer, poly(triphenylamine-alt-biphenylene vinylene) (TPA-PBPV), using a solution-assisted template wetting technique. TPA-PBPV was also coated on the surface of electrospun polyacrylonitrile (PAN) nanofiber nonwoven membrane. The extremely large surface area, highly porous fibrous structure, optical scattering and evanescent-wave guiding effect imparted these one-dimensional (1D) nanofibrous materials with highly improved sensory ability to 2,4,6-trinitrotoluene (TNT) vapors and higher quenching efficiency than that of the neat TPA-PBPV films. The results suggest that nanofibrous structures could be a promising strategy to improve the sensory efficiency of fluorescent chemosensors.

Numerical simulations on warm forming of stainless steel with trip-effect

In steels with TRIP-effect, a phase transformation from the retained-austenite to martensite occurs during forming, and it significantly affects hardening behaviours. Such an effect is sensitive to the amount of strain as well as the temperature variation. For materials with a strong TRIP-effect, new forming techniques are needed to develop that can lead to lighter and stronger components in automotive industry. This paper presents a coupled thermo-mechanical finite element modelling and simulation of a warm deep drawing of austenitic stainless steel (including a TRIP-effect) using LS-DYNA and temperature effect on forming process of such materials is investigated.

Microengineering of supramolecular soft materials by design of the crystalline fiber networks

Crystalline spherulitic fiber networks are commonly observed in polymeric and supramolecular functional materials. The elasticity of materials with this type of network is low if interactions between the individual spherulites are weak (mutually exclusive). Improving the elasticity of these materials is necessary because of their important applications in many fields. In this work, the engineering of the microstructures and rheological properties of this type of material is carried out. A small molecule organogel formed by the gelation of N-lauroyl-L-glutamic acid di-n-butylamide (GP-1) in propylene glycol (PG) is used as an example. The elasticity of this material is improved by controlling the thermodynamic driving force, the supersaturation of the gelator, and by using a selected copolymer additive to manipulate the primary nucleation of GP-1. Because of the weak interactions between the GP-1 spherulites, with the same fiber mass, the elasticity of GP-1/PG gel is less than half of those of the other two gels formed by GP-1 and 2-hydroxystearlic acid in solvent benzyl benzoate (BB), which are supported by interconnecting spherulitic fiber networks. This work develops a robust approach to the engineering of supramolecular functional materials especially those with mutually exclusive spherulite fiber networks.