Parametric investigation and measurement of near end and far end crosstalk in multiconductor microstrip transmission lines

This paper investigates and measures the near end and far end crosstalk in the multiconductor transmission line (MTL) mounted on the PCB by varying the parameters which are associated with physical dimension, characteristic of the substrate and the nature of input signal. With the variation of these factors, the coupling inductance and capacitance vary causing crosstalk. By using the method of moment (MoM), the per unit length parameters are calculated for microstrip lines. Subcircuit model is used to investigate the time domain and frequency domain analysis of near field and far field crosstalk. This parametric investigation is very useful for designing high speed interconnectors on PCB substrates. Some experimental results are presented to validate the analytical findings.

Electromagnetic receiving properties of overhead power line

This paper examines the use of overhead power transmission lines as electromagnetic sensors for detecting electric discharges caused by defective power transmission equipment. The experimental study involved the use of a spark gap (point-point configuration) and two HV conductors of different lengths to simulate electric discharge that takes place on transmission line. The experimental results show that large amount of energy are coupled onto the conductors and the amount of electromagnetic energy is dependent on the length of the conductor and the distance between the source and the conductor.

Windfarms, powerlines and phone masts : the changing face of stigma

Previous research has identified varying degrees of stigma attached to high voltage overhead transmission lines (HVOTLs) depending upon characteristics such as visibility, size, location and the potential impact on house value. In addition to HVOTLs there are other common types of infrastructure, namely mobile phone towers and windfarms, that are also large highly visible
structures and can exhibit similar characteristics. These similarities include varying levels of visibility from properties in the immediate vicinity, a high general profile in society and varying perceptions from surrounding residents about possible side effects. This research broadens the framework originally developed to study HVOTLs to encompass mobile phone towers and windfarms. It undertakes a literature review of research in this area and proposes a research methodology for identifying and quantifying the varying levels of stigma attached to these three forms of infrastructure. The final results will enable the resulting effect on property values to be better understood, and assist developers to fully understand their effect on devaluing land prices.

Design and simulation of a low voltage wide band RF MEMS switch

This paper presents design of an electrostatic wide band shunt capacitive coupling RF MEMS switch with low actuation voltage. The key factors of the RF MEMS switch design are the proper scattering parameters, low actuation voltage, and the cost of the fabrication process. An overview of the recent low actuation voltage RFMEMS switches has been presented. These designs still suffer from the complexity of process, lack of reliability, limitation of frequency band, and process cost. RF characteristics of a shunt RF MEMS switches are specified mostly by coupling capacitor in upstate position of the membrane Cu. This capacitor is in trade-off with actuation voltage. In this work, the capacitor is eliminated by using two short high impedance transmission lines, at the input and output of the switch. The simulation results demonstrate an improvement in the RF characteristic of the switch.

RF techniques for lowering the actuation voltage of RF MEMS shunt capacitor switch for C-K band

Increasing the capacitance ratio in RF MEMS shunt capacitive switch will increase its RF performance but also raise its actuation voltage. To improve the RF performance of the switch without increasing its capacitance ratio, this paper explores two methods: reducing the LC resonance from the mm-wave into the X-band by using an inductive bridge, and using two short high impedance transmission lines at both ends of the CPW line. Accordingly, this paper presents the design and simulation of an electro-static low actuation voltage and a very high isolation multipurpose switch with a very large bandwidth. The simulation results are presented and discussed.

Nonlinear large deformation dynamic analysis of electroactive polymer actuators

Electroactive polymers have attracted considerable attention in recent years due to their sensing and actuating properties which make them a material of choice for a wide range of applications including sensors, biomimetic robots, and biomedical micro devices. This paper presents an effective modeling strategy for nonlinear large deformation (small strains and moderate rotations) dynamic analysis of polymer actuators. Considering that the complicated electro-chemo-mechanical dynamics of these actuators is a drawback for their application in functional devices, establishing a mathematical model which can effectively predict the actuator's dynamic behavior can be of paramount importance. To effectively predict the actuator's dynamic behavior, a comprehensive mathematical model is proposed correlating the input voltage and the output bending displacement of polymer actuators. The proposed model, which is based on the rigid finite element (RFE) method, consists of two parts, namely electrical and mechanical models. The former is comprised of a ladder network of discrete resistive-capacitive components similar to the network used to model transmission lines, while the latter describes the actuator as a system of rigid links connected by spring-damping elements (sdes). Both electrical and mechanical components are validated through experimental results.

Nonlinear adaptive excitation controller design for multimachine power systems

This paper presents a nonlinear adaptive excitation control scheme to enhance the dynamic stability of multimachine power systems. The proposed controller is designed based on the adaptive backstepping technique where the mechanical power input to the generators and the damping coefficient of each generator are considered as unknown. These unknown quantities are estimated through the adaption laws. The adaption laws are obtained from the formulation of Lyapunov functions which guarantee the convergence of different physical quantities of generators such as the relative speed, terminal voltage, and electrical power output. The proposed scheme is evaluated by applying a three-phase short-circuit fault at one of the key transmission lines in an 11-bus test power system and compared with an existing backstepping controller and conventional power system stabilizer (CPSS). Simulation results show that the proposed scheme is much more effective than existing controllers.

Design and simulation of a low-actuation-voltage MEMS switch

This paper presents a low-actuation-voltage micro-electromechanical system (MEMS) capacitive shunt switch which has a very large bandwidth (4 GHz to 24 GHz). In this work, the isolation of MEMS switch is improved by adding two short high impedance transmission lines at the beginning and end of a coplanar waveguide (CPW). Simulating the switch demonstrates that a return loss (S11) is less than -26 dB for the entire frequency band, and perfect matching at 20 GHz in upstate position. A ramp dual pulse driver is also designed for reducing the capacitive charge injection for considering the reliability of the switch. The simulation results show that the shifting of voltage due to the capacitive charge is reduced by more than 35% of the initial value. Finally, the dynamic behavior of the MEMS switch is simulated by modal analysis and using CoventorWare to calculate the natural frequencies of the switch and its mode shapes. The switching ON and OFF time are 4.48 and 2.43 μs, respectively, with an actuation voltage of less than 15 V.