Parametric investigation and measurement of near end and far end crosstalk in multiconductor microstrip transmission lines

This paper investigates and measures the near end and far end crosstalk in the multiconductor transmission line (MTL) mounted on the PCB by varying the parameters which are associated with physical dimension, characteristic of the substrate and the nature of input signal. With the variation of these factors, the coupling inductance and capacitance vary causing crosstalk. By using the method of moment (MoM), the per unit length parameters are calculated for microstrip lines. Subcircuit model is used to investigate the time domain and frequency domain analysis of near field and far field crosstalk. This parametric investigation is very useful for designing high speed interconnectors on PCB substrates. Some experimental results are presented to validate the analytical findings.

Electromagnetic receiving properties of overhead power line

This paper examines the use of overhead power transmission lines as electromagnetic sensors for detecting electric discharges caused by defective power transmission equipment. The experimental study involved the use of a spark gap (point-point configuration) and two HV conductors of different lengths to simulate electric discharge that takes place on transmission line. The experimental results show that large amount of energy are coupled onto the conductors and the amount of electromagnetic energy is dependent on the length of the conductor and the distance between the source and the conductor.

Pi-shaped MEMS architecture for lowering actuation voltage of RF switching

A wide band low actuation capacitive coupling electrostatic RF MEMS switching device is presented in this paper. The device includes a pi-shaped matching architecture containing two switches connected by a high impedance short transmission line. The device can act as a switch for any desired frequency whilst requiring only 12volts for actuation. By optimizing the length and the characteristic impedance of the transmission line, the switch can be tailored for desired frequency bands. The switch is calculated and simulated for Ka to V frequency bands demonstrating excellent improvements of RF characteristics.

Design and simulation of a tunable MEMS filter for wireless biomedical signal transceivers

This paper presents a new architecture for a high quality tunable MEMS filter that can be used in wireless biomedical signal transceivers. It consists of a π match circuit with two shunt capacitive coupling switches separated by a piece of high impedance short transmission line, and also a series switch placed at the quarter wavelength distance away from the π match circuit. The low actuation voltage and also tunability are important features of the design objective. All portions of the filter can be realized simultaneously. Thus, the filter docs not require any extra steps during its fabrication, and is not costly. The simulation results confirm the good performance of the filter.

RF techniques for lowering the actuation voltage of RF MEMS shunt capacitor switch for C-K band

Increasing the capacitance ratio in RF MEMS shunt capacitive switch will increase its RF performance but also raise its actuation voltage. To improve the RF performance of the switch without increasing its capacitance ratio, this paper explores two methods: reducing the LC resonance from the mm-wave into the X-band by using an inductive bridge, and using two short high impedance transmission lines at both ends of the CPW line. Accordingly, this paper presents the design and simulation of an electro-static low actuation voltage and a very high isolation multipurpose switch with a very large bandwidth. The simulation results are presented and discussed.

Nonlinear dynamic modeling of ionic polymer conductive network composite actuators using rigid finite element method

Ionic polymer conductive network composite (IPCNC) actuators are a class of electroactive polymer composites that exhibit some interesting electromechanical characteristics such as low voltage actuation, large displacements, and benefit from low density and elastic modulus. Thus, these emerging materials have potential applications in biomimetic and biomedical devices. Whereas significant efforts have been directed toward the development of IPMC actuators, the establishment of a proper mathematical model that could effectively predict the actuators' dynamic behavior is still a key challenge. This paper presents development of an effective modeling strategy for dynamic analysis of IPCNC actuators undergoing large bending deformations. The proposed model is composed of two parts, namely electrical and mechanical dynamic models. The electrical model describes the actuator as a resistive-capacitive (RC) transmission line, whereas the mechanical model describes the actuator as a system of rigid links connected by spring-damping elements. The proposed modeling approach is validated by experimental data, and the results are discussed. © 2014 Elsevier B.V. All rights reserved.

Applying inverse just-noticeable-differences of velocity to position data for haptic data reduction

ust-Noticeable-Differences (JND) as a dead-band in perceptual analysis has been widely used for more than a decade. This technique has been employed for data reduction in hap tic data transmission systems by several researchers. In fact, researchers use two different JND coefficients that are JNDV and JNDF for velocity and force data respectively. For position data, they usually rely on the resolution of hap tic display device to omit data that are unperceivable to human. In this paper, pruning undesirable position data that are produced by the vibration of the device or subject and/or noise in transmission line is addressed. It is shown that using inverse JNDV for position data can prune undesirable position data. Comparison of the results of the proposed method in this paper with several well known filters and some available methods proposed by other researchers is performed. It is shown that combination of JNDV could provide lower error with desirable curve smoothness, and as little as possible computation effort and complexity. It also has been shown that this method reduces much more data rather than using forward-JNDV.

X-ray diffraction line broadening from gold and platinum thin films

X-ray diffraction line profile analysis has been used to study the microstructure of (Ill) oriented gold and platinum thin films deposited by thermal evaporation and DC magnetron sputtering. In addition to crystallite size broadening, the profiles from these films displayed broadening arising from dislocations. A parallel investigation, using transmission electron microscopy (TEM) was undertaken to study the nature of dislocations formed, and to provide information on the dimensions of the crystallite columns in the films. X-ray data were collected at room temperature to determine the anisotropy of the broadening with (hkl), using a Siemens D5000 powder diffractometer (CuKa radiation) and two high-resolution synchrotron instruments (BM 16 at the ESRF [A=0.35A] and station 2.3 at the Daresbury laboratory. Two approaches to instrument deconvolution were investigated; Fourier deconvolution and fundamental parameters profile fitting, using Lab6 as a reference material to determine the instrument profile function. After removal of the crystallite size broadening contribution from the measured integral breadths, the residual microstrain broadening was modelled assuming dislocations based on a FCC a/2<110>{ Ill} slip system. The results of the X-ray analysis agreed with dark field TEM micrographs, which showed that many of the crystallites contained dislocations of mixed character (screw- edge).

In-situ studies of X-ray diffraction line profiles from strained copper foils

The development of an in-situ tensometer is described along with preliminary results of x-ray line profiles from copper foils under tensile stress. The tensometer was designed and constructed on the high resolution diffraction instrument, Station 2.3 at the synchrotron radiation source (SRS) Daresbury Laboratory, and is capable of collecting data in either symmetric or asymmetric geometry including transmission and reflection modes. Experiments were carried out using 18 J..Lm thick copper foil up to strain levels of 5 % using both symmetric reflection and symmetric transmission diffraction. All profiles displayed diffraction broadening and asymmetry which increased with strain. In addition, the asymmetry observed in symmetric transmission was associated with extended tails on the low angle side of the profiles, but in symmetric reflection data the opposite asymmetry was observed. In the analysis, the measured profiles were fitted using the software TOPAS, a fundamental parameters approach to profile fitting. The instrumental profile function was characterised and modelled using annealed LaB6 powder. The diffraction broadening was then determined by refining the convolution of a Voigt function, an asymmetric exponential function and a fixed instrument function to reproduce the observed broadened profiles. The integral breadth and asymmetry results display a strong order dependence and increase almost linearly with strain. The results were interpreted by assuming crystallite size broadening in combination with dislocation broadening arising from fcc a/2( 110) {Ill } dislocations.

Effect of composition and processing parameters on the formation of nano-bainite in advanced high strength steels

The nano-bainitic microstructures were compared in a 0.79C-1.5Si-1.98Mn-0.24Mo-1.06Al (wt%) steel after isothermal heat-treatment and a Fe-0.2C-1.5Mn-1.2Si-0.3M0-0.6Al-0.02Nb (wt%) steel after controlled thermo-mechanical processing. The microstructure for both steels consisted of bainite. The microstructural characteristics of bainite, such as the morphology of the nano-bainite and thicknesses of bainitic ferrite and retained austenite layers, as a function of steel composition and processing was studied using transmission electron microscopy (TEM). It was found that the nano-bainitic structure can be formed in the low alloy steel through thermomechanical processing. Atom probe tomography (APT) was employed as a powerful technique to determine local composition distributions in three dimensions with atomic resolution. The important conclusions from the APT research were that the carbon content of bainitic ferrite is higher than expected from paraequilibrium level of carbon in ferrite for both steels and that Fe-C clusters and fine particles are formed in the bainitic ferrite in both steels despite the high level of Si.

An in situ method for the study of strain broadening using synchrotron X-ray diffraction

A tensonometer for stretching metal foils has been constructed for the study of strain broadening in X-ray diffraction line profiles. This device, which is designed for use on powder diffractometers and was tested on Station 2.3 at Daresbury Laboratory, allows in situ measurements to be performed on samples under stress. It can be used for data collection in either transmission or reflection modes using either symmetric or asymmetric diffraction geometries. As a test case, measurements were carried out on an 18 µm-thick copper foil experiencing strain levels of up to 5% using both symmetric reflection and symmetric transmission diffraction. All the diffraction profiles displayed peak broadening and asymmetry which increased with strain. The measured profiles were analysed by the fundamental-parameters approach using the TOPAS peak-fitting software. All the observed broadened profiles were modelled by convoluting a refineable diffraction profile, representing the dislocation and crystallite size broadening, with a fixed instrumental profile predetermined using high-quality LaB6 reference powder. The deconvolution process yielded `pure' sample integral breadths and asymmetry results which displayed a strong dependence on applied strain and increased almost linearly with applied strain. Assuming crystallite size broadening in combination with dislocation broadening arising from f.c.c. a/2〈110〉{111} dislocations, the variation of mechanical property with strain has been extracted. The observation of both peak asymmetry and broadening has been interpreted as a manifestation of a cellular structure with cell walls and cell interiors possessing high and low dislocation densities.

A mathematical model for the spread of streptococcus pneumoniae with transmission due to sequence type

This paper discusses a simple mathematical model to describe the spread of Streptococcus pneumoniae. We suppose that the transmission of the bacterium is determined by multi-locus sequence type. The model includes vaccination and is designed to examine what happens in a vaccinated population if MLSTs can exist as both vaccine and non vaccine serotypes with capsular switching possible from the former to the latter. We start off with a discussion of Streptococcus pneumoniae and a review of previous work. We propose a simple mathematical model with two sequence types and then perform an equilibrium and (global) stability analysis on the model. We show that in general there are only three equilibria, the carriage-free equilibrium and two carriage equilibria. If the effective reproduction number Re is less than or equal to one, then the carriage will die out. If Re > 1, then the carriage will tend to the carriage equilibrium corresponding to the multi-locus sequence type with the largest transmission parameter. In the case where both multi-locus sequence types have the same transmission parameter then there is a line of carriage equilibria. Provided that carriage is initially present then as time progresses the carriage will approach a point on this line. The results generalize to many competing sequence types. Simulations with realistic parameter values confirm the analytical results.