Enhanced degradation efficiency of toluene using titania/silica photocatalysis as a regeneration process

Three kinds of titania/silica pellets were prepared using the sol-gel method with surface areas of 50.4m² g-1, 421.1m².g^-1 and 89.1m².g^-1. An annular reactor was designed and built to determine the degradation efficiency of toluene and to investigate the relationship between the adsorption and desorption-photocatalytic processes. Surface area is an important factor influencing the adsorption-photocatalytic efficiency. Higher surface areas of pellets contribute to high rates of conversion of toluene. Un-reacted toluene and reaction intermediates accumulating on their surface deactivated the titania/silica catalyst. To overcome this problem, the adsorption and regeneration process were alternated in a dual reactor system. Connecting or disconnecting the toluene feed gas enabled one reactor to adsorb toluene, while the second reactor was regenerated by photocatalysis. Using UV irradiation and titania/silica pellets with high BET surface area (421.1 m².g^-1), the alternating adsorption/regeneration processes kept the degradation efficiency of toluene at 90% after 8 hours operation. By improving the adsorption-photocatalysis efficiency, and minimising the generation and accumulation of intermediate on the surface of pellets, the method extended catalyst life and maintained a high degradation efficiency of toluene.

Using titania photocatalysts to degrade toluene in a combined adsorption and photocatalysis process

Three types of titania supported materials including titanium dioxide and silicon dioxide composite, titania-coated activated carbon and titania-coated glass beads were prepared and used as photocatalysts to remove toluene from an air stream. Their surface areas were analysed. TEM image reveals titania-silica composites were nanostructured aggregates. XRD was used to determine their crystalline phase which was 100% anatase for the titania component. A fixed bed reactor was designed and built in the laboratory, the toluene with initial concentration of 300 ppm (1149 mg/m³) was fed into the reactor, the destruction efficiencies of toluene were determined by the gas analyser. It was also found that TiO₂-SiO₂ aggregates with high surface area (421.1 m²/g) achieved high destruction efficiencies. The combined effects of adsorption and photocatalysis were further studied by comparing the performance of pure activated carbon (surface area of 932.4 m²/g) and TiO₂ coated activated carbon with BET surface area of 848.4 m²/g. It was found that the TiO₂ coated activated carbon demonstrated comparable results to pure activated carbon, and most importantly, the TiO₂-coated activated carbon can be effectively regenerated by UV irradiation, and was reused as adsorbent. The experimental result of titania-coated glass beads demonstrated a steady degradation efficiency of 15% after a period of 17 hours. It helped to understand that photocatalysis degradation ability of the TiO₂ was constant regardless of the adsorption capacity of the catalysts. This photocatalytic property can be used to degrade the adsorbed toluene and regenerate the catalyst. This study revealed that if the experiments were designed to use adsorption to remove toluene and followed by regeneration of adsorbent using photocatalysis, it could achieve a very high removal efficiency of toluene and reduce the regeneration cost of saturated adsorbent.

Decay of electrical conductivity in p-toluene sulfonate doped polypyrrole films

Long term performance of conductivity of p-toluene sulfonic acid (pTSA) doped electrochemically synthesized polypyrrole (PPy) films was estimated from accelerated aging studies between 80 °C and 120 °C. Conductivity decay experiments indicated that overall aging behavior of PPy films deviated from first order kinetics at prolonged aging times at elevated temperatures. However, an approximate value for the activation energy of the conductivity decay of PPy was calculated as E=47.4 kJ/mol, enabling an estimate of a rate constant of k=8.35×10⁻⁶/min at 20 °C. The rate of decrease of conductivity was not only temperature dependent but also influenced by the dopant concentration. A concentration of 0.005 M pTSA in the electrolyte resulted in a conductive film and when this film was exposed to 120 °C for a period of 40 h, the conductivity decayed to about 1/20 of its original value. The concentration of pTSA was increased to 0.05 mol/l and when the resulting film was aged in the same way, it showed a decrease in the conductivity to about 1/3 of its original value. Both microwave transmission and dc conductivity data revealed that highly doped films were considerably more electrically stable than lightly doped films. The dopant had a preserving effect on the electrical properties of PPy.

Liquid phase adsorption kinetics and equilibrium of toluene by novel modified-diatomite

The adsorption equilibria of toluene from aqueous solutions on natural and modified diatomite were examined at different operation parameters such as pH, contact time, initial toluene concentration was evaluated and optimum experimental conditions were identified. The surface area and morphology of the nanoparticles were characterized by SEM, BET, XRD, FTIR and EDX analysis. It was found that in order to obtain the highest possible removal of toluene, the experiments can be carried out at pH 6, temperature 25°C, an agitation speed of 200 rpm, an initial toluene concentration of 150 mg/L, a centrifugal rate of 4000 rpm, adsorbent dosage = 0.1 g and a process time of 90 min. The results of this work show that the maximum percentage removal of toluene from aqueous solution in the optimum conditions for NONMD was 96.91% (145.36 mg/g). Furthermore, under same conditions, the maximum adsorption of natural diatomite was 71.45% (107.18 mg/g). Both adsorption kinetic and isotherm experiments were carried out. The experimental data showed that the adsorption follows the Langmuir model and Freundlich model on natural and modified diatomite respectively. The kinetics results were found to conform well to pseudo-second order kinetics model with good correlation. Thus, this study demonstrated that the modified diatomite could be used as potential adsorbent for removal of toluene from aqueous solution.

Characterization of conductive polyprrole coated wool yarns

Wool yarns were coated with conducting polypyrrole by chemical synthesis methods. Polymerization of pyrrole was carried out in the presence of wool yarn at various concentrations of the monomer and dopant anion. The changes in tensile, moisture absorption, and electrical properties of the yarn upon coating with conductive polypyrrole are presented. Coating the wool yarns with conductive polypyrrole resulted in higher tenacity, higher breaking strain, and lower initial modulus. The changes in tensile properties are attributed to the changes in surface morphology due to the coating and reinforcing effect of conductive polypyrrole. The thickness of the coating increased with the concentration of p-toluene sulfonic acid, which in turn caused a reduction in the moisture regain of the wool yarn. Reducing the synthesis temperature and replacing p-toluenesulfonic acid by anthraquinone sulfonic acid resulted in a large reduction in the resistance of the yarn.

Hydrolysis of (Me3SiCH2)PhSnCl2. Isomerisation of the dimeric tetraorganodistannoxane [(Me3SiCH2)Ph(Cl)SnOSn(Cl)-Ph(CH2SiMe3)]2

The hydrolysis of (Me₃SiCH₂)PhSnCl₂( 1) was studied under two different reaction conditions (i) by using an excess of aqueous NaOH in toluene at reflux temperature and (ii) by using small amounts of NEt₃ and water in CH₂Cl₂ at room temperature. For (i) the products  (Me₃SiCH₂)Ph₂SnOSnPh₂(CH₂SiMe₃)( 2) and [(Me₃SiCH₂Sn)₁₂O₁₄(OH)₆](OH)₂( 3) were isolated indicating that a phenyl group migration took place. For (ii) the dimeric tetraorganodistannoxane [(Me₃SiCH₂)Ph(Cl)SnOSn(Cl)Ph(CH₂SiMe₃)]₂( 4) was obtained. In solution, 4 exists as an equilibrium mixture of all five possible isomers 4a–4e; in the solid state two of these isomers 4d and 4e co-crystallized in the same crystal modification. The observation of interconvertible isomers of 4 was attributed to the kinetic lability of the ladder-like Sn4O2Cl4 structural motif. Compounds 1 and 4 were investigated by X-ray crystallography.

Degradation of VOCs by phototcatalytic oxidation reactor using TiO2 pellets

Volatile Organic Compounds (VOCs) are air pollutants that come from burning fossil fuels and industrial emissions. They have potentially adverse health effects being carcinogenic and highly persistent in the environment. The use of photocatalytic oxidation to remove VOCs has the potential to be applied in indoor air quality improvement and industrial emission control. A fixed bed photocatalytic reactor was designed and built. UV black light lamps were installed in the reactor to provide a source of UV radiation. A non-film titania media as pellets were placed on the three fixed beds within the reactor. Toluene and acetone were used as indicators of VOCs during the experiment. With a flow rate of 12.75l/min, the oxidation efficiencies were obtained at four different concentrations of acetone laden gas streams ranging from 40ppm to 250ppm. It was found that the lower the acetone concentration of the untreated inlet gas, the higher the oxidation efficiency. The oxidation efficiency was in the range of 40–70% for various concentrations of untreated gases. Two concentrations of toluene laden gas stream were also tested using the same reactor. The oxidation efficiencies were found as 50% for 120ppm toluene gas and 45% for 300ppm toluene gas. It was found that the times required for toluene to reach oxidization equilibrium have been halved than for acetone gas stream. Other parameters such as flow rate and UV intensity were also altered to see their effects on the oxidation efficiency. A full spectrum scan was carried out using a Bio-rad Infrared spectrometer. It was found that the main components of the treated gas stream from the outlet of the reactor were CO2 and water along with small amount of untreated acetone. The suspected intermediates of aliphatic hydrocarbons and CO were found in very minimal amounts or undetectable. The research experiments supported that the TiO2 pellets can work effectively in a fixed bed photocatalytic reactor and achieve significant oxidation efficiencies for degradation of toluene and acetone as indicators of VOCs.

A comparative study on preparation of TiO2 pellets as photocatalysts based on different precursors

The porous Ti0₂ pellets were prepared based on pigment grade titaina, P25 titania powder and titaniurn(lV) butoxide. The characterization was done with X-Ray diffraction, scanning electron microscopy and BET measurements. The result shows that Ti0₂ pellets by using titaniurn(IV) butoxide with some addictive have the best surface porosity, with specific surface area of 196.9m²/g. For pigment grade titania and P25 titania powder, it is still effective to enhance the surface area after reassembling. The surface area increased from 11.6 to 29.2 m²/g for pigment grade titania and from 50 to 84.4 m²/g for P25 titania powder. Furthermore, it has been investigated on how to optimize and get the highest surface area by controlling the sintering temperature, reaction temperature, pH of solution, and the amount of alcohol and addictive of surfactant during preparation. The experimental photocatalytic degradation of acetone and toluene was performed using titania pellets made from P25 titania powder.

Synthesis and structure of bis(para-methoxyphenyl)selenoxide and its monohydrate. theoretical considerations of the hydration of diorganoselenium oxides

The title compound was prepared by base hydrolysis of (p-MeOC₆H₄)₂SeCl₂ in water and isolated as the crystalline monohydrate, (p-MeOC₆H₄)₂SeO·H₂O, in which the water molecule is associated via hydrogen-bonding. Water-free (p-MeOC₆H₄)₂SeO was obtained crystalline after drying and recrystallisation from toluene. Both crystal phases were investigated by single crystal X-ray diffraction. Preliminary DFT calculations at the B3LYP/LANL2DZdp level of theory suggest that the hydrogen bonded complexes R₂SeO·H₂O (R = H, Me, Ph) are by 2.79, 3.36 and 11.10 kcal mol^-1 more stable than the corresponding elusive diorganoselenium dihydroxides R₂Se(OH)₂. The hydrogen bond energies of R₂SeO·H₂O (R = H, Me, Ph) are 5.98, 7.18 and 5.89 kcal mol^-1.

Electromagnetic shielding properties of polypyrrole/polyester composites in the 1–18 GHz frequency range

The dielectric characteristics of conducting polymer-coated textiles in the frequency range 1–18 GHz were investigated using a non-contact, non-destructive free space technique. Polypyrrole coatings were applied by solution polymerization on fabric substrates using a range of concentrations of para-toluene-2-sulfonic acid (pTSA) as dopant and ferric chloride as oxidant. The conducting polymer coatings exhibited dispersive permittivity behaviour with a decrease in real and imaginary components of complex permittivity as frequency increased in the range tested. Both the permittivity and the loss factor were affected by the polymerization time of the conductive coating. It was found that the total shielding efficiency of these conductive fabrics is significant at short polymerization times and increases to values exceeding 80% with longer polymerization times. The reflection contribution to electromagnetic shielding also increases with polymerization time.

Electromagnetic interference shielding and radiation absorption in thin polypyrrole films

Results of permittivity measurements, electromagnetic interference shielding effectiveness, and heat generation due to microwave absorption in conducting polymer coated textiles are reported and discussed. The intrinsically conducting polymer, polypyrrole, doped with anthraquinone-2-sulfonic acid (AQSA) or para-toluene-2-sulfonic acid (pTSA) was applied on textile substrates and the resulting materials were investigated in the frequency range 1–18 GHz. The 0.54 mm thick conducting textile/polypyrrole composites absorbed up to 49.5% of the incident 30–35 W microwave radiation. A thermography station was used to monitor the temperature of these composites during the irradiation process, where absorption was confirmed via visible heat losses. Samples with lower conductivity showed larger temperature increases caused by microwave absorption compared to samples with higher conductivity. A sample with an average sheet resistivity of 150 Ω/sq. showed a maximum temperature increase of 5.27 °C, whilst a sample with a lower resistivity (105 Ω/sq.) rose by 3.85 °C.

Conductive poly(α,ω-bis(3-pyrrolyl)alkanes)-coated wool fabrics

Cross-linked poly(α,ω-bis(3-pyrrolyl)alkanes) were directly applied to woven wool substrates by either chemical, vapour or mist polymerization methods. Choice of dopant could greatly improve the surface resistance. The optimum coating on textiles with the lowest surface resistance, highest colour-fastness and stability was achieved using a mist polymerization method with 1,8-bis(pyrrolyl)octane, iron(III) chloride (FeCl₃) as the oxidant and p-toluene sulfonic acid sodium salt (pTSA) as the dopant.

Dielectric characterization of conducting textiles using free space transmission measurements: accuracy and methods for improvement

The dielectric behaviour of in-situ polymerized thin polypyrrole (PPy) films on synthetic textile substrates were obtained in the 1–18 GHz region using free space transmission and reflection methods. The PPy/para-toluene-2-sulphonic acid (pTSA) coated fabrics exhibited an absorption dominated total shielding effectiveness (SE) of up to −7.34 dB, which corresponds to more than 80% of incident radiation. The permittivity response is significantly influenced by the changes in ambient conditions, sample size and diffraction around the sample. Mathematical diffraction removal, time-gating tools and high gain horns were utilized to improve the permittivity response. A narrow time-gate of 0.15 ns produced accurate response for frequencies above 6.7 GHz and the high gain horns further improved the response in the 7.5–18 GHz range. Errors between calculated and measured values of reflection were most commonly within 2%, indicating good accuracy of the method.

New insights in asymmetric tetraorganodistannoxane ladder formation. A NMR-spectroscopic and crystallographic study

The syntheses of the asymmetrically substituted tetraorganodistannoxanes [t-Bu₂(X)SnOSn(Y)(CH₂SiMe₃)₂1₂ (1, X = Y = OH; 2, X = Cl, Y = OH; 3, X = Y = Cl) are reported and their structures in solution and in the solid state are characterized by multinuclear NMR spectroscopy and single crystal X-ray analyses. In toluene, the tetrahydroxy-substituted derivative 1 is in equilibrium with the organotin oxides cyclo-[t-Bu₂Sn{OSn(CH₂SiMe₃)₂}₂O] (4), cyclo[(Me₃SiCH₂)₂Sn(OSnt-Bu₂)₂O] (5), and cyclo-(t-Bu₂SnO)₃, and some additional, undefined species containing pentacoordinated tin atoms. In contrast, the dihydroxydichloro-substituted derivative 2 is inert in solution.