Atom probe tomography investigation of heterogeneous short-range ordering in the 'komplex' phase state (K-state) of Fe-18Al (at.%)

We study an Fe-18Al (at.%) alloy after various thermal treatments at different times (24-336 h) and temperatures (250-1100 °C) to determine the nature of the so-called 'komplex' phase state (or "K-state"), which is common to other alloy systems having compositions at the boundaries of known order-disorder transitions and is characterised by heterogeneous short-range-ordering (SRO). This has been done by direct observation using atom probe tomography (APT), which reveals that nano-sized, ordered regions/particles do not exist. Also, by employing shell-based analysis of the three-dimensional atomic positions, we have determined chemically sensitive, generalised multicomponent short-range order (GM-SRO) parameters, which are compared with published pairwise SRO parameters derived from bulk, volume-averaged measurement techniques (e.g. X-ray and neutron scattering, Mössbauer spectroscopy) and combined ab-initio and Monte Carlo simulations. This analysis procedure has general relevance for other alloy systems where quantitative chemical-structure evaluation of local atomic environments is required to understand ordering and partial ordering phenomena that affect physical and mechanical properties.

Biomimetic coating on pure titanium submitted to different surface treatments

Titanium (Ti) plates were firstly treated to form various types of oxide layers on the surface and then immersed into simulated body fluid (SBF) to evaluate the apatite forming ability. The surface morphology and roughness of the different oxide layers were measured by atomic force microscopy (AFM), and the surface energies were determined based on the Owens-Wendt (OW) methods. It was found that Ti samples after Alkali-Heat treatment (AH) achieved the best apatite formation after soaking in SBF for 3 weeks, compared to those without treatment, thermal or H₂O₂ oxidation. Furthermore, contact angle measurement revealed that the oxide layer on the alkali-heat treated Ti samples possessed the highest surface energy. The results indicate that the apatite inducing ability of a titanium oxide layer is linked to its surface energy. Apatite nucleation is easier on a surface with a higher surface energy.

Mechanisms governing the enhanced thermal stability of acid and base treated polypyrrole

One of the major problems associated with the use of polypyrrole (PPy) in a practical engineering application is its poor thermal stability at elevated temperatures, especially in the presence of oxygen and moisture. Several authors have shown that enhanced stability can be achieved through treatment with simple acids and bases. This paper presents a summary of the possible structural changes which occur as a result of these treatments and those that appear to be related to enhanced conductivity stability. A slight increase in conductivity (10–20%) is observed for acid treated PPy films which is found to be the result of protonation of the pyrrole structure. This effect is dramatically enhanced by treatment at high temperatures where an increase in conductivity of >84% can be achieved. Base treatment of the PPy films results in the deprotonation of the pyrrole structure leading to the loss of conductivity (>40%). Preliminary X-ray Photoelectron Spectroscopy (XPS) results indicate that both acid and base treatment resulted in the elimination of reactive sites for oxygen. Long term thermal ageing of these treated films were conducted at 150 °C in air. The conductivity decay behaviour was found to follow multiple first order chemical reaction kinetics.

Silk fibroin as a water-soluble bio-resist and its thermal properties

Thermal diffusivity of silk fibroin films, α = (1.6 ± 0.24) × 10-7 m2 s-1, was measured by a direct contact method. It was shown to be reduced down to ∼1 × 10-7 m2 s-1 in the crystallized phase, consistent with the multi-domain composition of β-sheet assemblies. Crystalline silk with β-sheets was made by dipping into alcohol and was used as a positive electron beam lithography (EBL) resist. It is shown by direct IR imaging of the 1619 cm-1 amide-I CO spectral signature and 3290 cm-1 amide-A N-H stretching band that an e-beam is responsible for unzipping β-sheets, which subsequently results in exposed areas returning to a water soluble state. This makes it possible to develop a water-based biocompatible silk resist and use it in lithography applications. The general principles of protein crystallization, traceable to spectral changes in IR amide bands of silk, can be used as a guide for the creation of new protein EBL resists and to quantify the electron dose required for solubility. Foam formation and laser treatments of silk can provide new approaches in surface functionalization and fabrication of 3D bio-scaffolds.