Improved fracture toughness of fire resistant composites through rapid curing

A study on the effect of material and fracture properties of phenolic composites cured with reduced thermal cycle times. These reductions were achieved using various techniques. The work highlights significant reductions in manufacturing times are possible for this group of materials and conveniently can also lead to improved properties.

Weldability of duplex stainless steel

Duplex stainless steels (DSSs) have many advantages due to the unique structural combination of ferrite and austenite grains. The structural change of these materials is very complex during welding, and it deteriorates the functional properties. This research investigates different welding processes such as laser beam, resistance, tungsten inert gas, friction stir, submerged arc, and plasma arc weldings considering the research available in the literature. The welding mechanism, change of material structure, and control parameters have been analyzed for every welding process. This analysis clearly shows that DSS melts in all most all welding processes, but the thermal cycle and maximum heat input are different. This difference affects the resulting structure and functional properties of the weld significantly.

Using small reverse cycle air conditioners in relocatable classrooms - a case study

A 9-month study of four relocatable school buildings, each retro-fitted with small reverse cycle air conditioners (ACs), was conducted to investigate their effectiveness in heating and cooling the classrooms. A comparison with data from previous studies found the energy used by the ACs for heating these temporary classrooms was only 19–20% of the energy used by individual gas heaters installed in permanent classrooms. When equipment efficiencies were considered, the AC units supplied 20–27% less energy to heat the classrooms. The possible reasons for this reduction in supplied energy are explored in this paper. CO2 emissions for the AC units in heating mode, however, were calculated to be 16% greater than for individual gas heaters. The AC units were also used for cooling and on an average the total annual energy consumption for heating and cooling was found to be 11.6 kWh m−2. Responses to a small survey of staff and students about the use and operation of the conditioners are presented. Their responses were more favourable than the predictions of comfort levels in the classrooms using the Predicted Mean Vote–Predicted Percentage of Dissatisfaction (PMV–PPD) model, which indicated “uncomfortable” conditions on average summer days at 3:00 p.m. and average winter days at 10:00 a.m. Background noise levels in the classrooms with the air conditioners in use were above the recommended maximum design level of 45 dB(A); levels of up to 65 dB(A) were measured.

Solar adsorption refrigeration : an alternative/auxiliary way for thermal storage for air conditioning

This paper presents an idea of using solar powered adsorption ice making system as an alternative or an auxiliary way for the traditional ice storage air conditioning systems. A simple solar adsorption refrigeration system runs in intermittent cycle. It makes cooling effect at night, and the cooling effect can be stored for the day use. It fits in well with the cycle of the existing off-peak ice storage air conditioning system. On the top of green effect of the solar powered ice making system, the idea is specifically beneficial for places where the price of the off-peak electricity is not significantly lower than peak price. Based on our many years experience on the solar ice making systems, the paper discusses the technical feature of the solar ice making technology and the solutions we are working on to attack the problems which may have potential damage to application of the solar ice making system for air conditioning purposes.

A medium-temperature solar thermal power system and its efficiency optimisation

This paper firstly expounds that the reheat-regenerative Rankine power cycle is a suitable cycle for the parabolic trough collector, a popular kind of collector in the power industry. In a thermal power cycle, the higher the temperature at which heat is supplied, the higher the efficiency of the cycle. On the other hand, for a given kind of collector at the same exiting temperature, the higher the temperature of the fluid entering the collector, the lower the efficiency of the collector. With the same exiting temperature of the solar field and the same temperature differences at the hottest end of the superheater/reheater and at the pinch points in the heat exchangers (e.g., the boiler) in the cycle, the efficiencies of the system are subject to the temperature of the fluid entering the collector or the saturation temperature at the boiler. This paper also investigates the optimal thermal and exergetic efficiencies for the combined system of the power cycle and collector. To make most advantage of the collector, the exiting fluid is supposed to be at the maximum temperature the collector can harvest. Hence, the thermal and exergetic efficiencies of the system are related to the saturation temperature at the boiler here.

A comprehensive framework for assessing the life cycle energy of building construction assemblies

Environmental decision making during the building design process has typically focused on improvements to operational efficiencies. Improvements to thermal performance and efficiency of appliances and systems within buildings both aim to reduce resource consumption and environmental impacts associated with the operation of buildings. Significant reductions in building energy and water consumption are possible; however often the impacts occurring across the other stages of a building‘s life are not considered or are seen as insignificant in comparison.

Previous research shows that embodied impacts (raw material extraction, processing, manufacture, transportation and construction) can be as significant as those related to building operation. There is, however, limited consistent and comprehensive information available for building designers to make informed decisions in this area. Often the information that is available is from disparate sources, which makes comparison of alternative solutions unreliable and risky. lt is also important that decisions are made from a life cycle perspective, ensuring that strategies to reduce environmental impacts from one life cycle stage do not come at the expense of an increase in overall life cycle impacts

A consistent and comprehensive framework for assessing and specifying building assemblies for enhanced environmental outcomes does not currently exist. This paper presents the initial findings of a project that aims to establish a database of the life cycle energy requirements of a broad range of construction assemblies, based on a comprehensive assessment framework. Life cycle energy requirements have been calculated for eight standard residential construction assemblies integrating an innovative embodied energy assessment technique with thermal performance simulation modelling and ranked according to their performance.

Solar thermal aided power generation

Fossil fuel based power generation is and will still be the back bone of our world economy, albeit such form of power generation significantly contributes to global CO2 emissions. Solar energy is a clean, environmental friendly energy source for power generation, however solar photovoltaic electricity generation is not practical for large commercial scales due to its cost and high-tech nature. Solar thermal is another way to use solar energy to generate power. Many attempts to establish solar (solo) thermal power stations have been practiced all over the world. Although there are some advantages in solo solar thermal power systems, the efficiencies and costs of these systems are not so attractive. Alternately by modifying, if possible, the existing coal-fired power stations to generate green sustainable power, a much more efficient means of power generation can be reached. This paper presents the concept of solar aided power generation in conventional coal-fired power stations, i.e., integrating solar (thermal) energy into conventional fossil fuelled power generation cycles (termed as solar aided thermal power). The solar aided power generation (SAPG) concept has technically been derived to use the strong points of the two technologies (traditional regenerative Rankine cycle with relatively higher efficiency and solar heating at relatively low temperature range). The SAPG does not only contribute to increase the efficiencies of the conventional power station and reduce its emission of the greenhouse gases, but also provides a better way to use solar heat to generate the power. This paper presents the advantages of the SAPG at conceptual level.

Seasonal winds drive water temperature cycle and migration patterns of Southern Australian giant crab Pseudocarcinus gigas

The giant crab Pseudocarcinus gigas occurs along the continental shelf break of southern Australia. During the summer alongshore winds cause cooler water to upwell onto the shelf, and the crabs move from deeper water onto the shelf where there is more food. The combination of a preferred thermal niche and a depth-stratified food supply defines the favorable foraging environments that enhance the growth of P. gigas. Climate change is expected to cause a southerly shift of the austral subtropical high-pressure belt, and modelers have predicted more upwelling-favorable winds. The associated increase in the circulation of cooler water across the shelf is likely to provide P. gigas with an increased access to benthic food resources and their growth rate may increase in some regions.

Optimising the life cycle energy performance of residential buildings

A holistic approach to low-energy building design is essential to ensure that any efficiency improvement strategies provide a net energy benefit over the life of the building. Previous work by the authors has established a model for informing low-energy building design based on a comparison of the life cycle energy demand associated with a broad range of building assemblies. This model ranks assemblies based on their combined initial and recurrent embodied energy and operational energy demand. The current study applies this model to an actual residential building in order to demonstrate the application of the model for optimising a building’s life cycle energy performance. The aim of this study was to demonstrate how the availability of comparable energy performance information at the building design stage can be used to better optimise a building’s energy performance. The life cycle energy demand of the case study building, located in the temperate climate of Melbourne, Australia, was quantified using a comprehensive embodied energy assessment technique and TRNSYS thermal energy simulation software. The building was then modelled with variations to its external assemblies in an attempt to optimise its life cycle energy performance. The alternative assemblies chosen were those shown through the author’s previous modelling to result in the lowest life cycle energy demand for each building element. The best performing assemblies for each of the main external building elements were then combined into a best-case scenario to quantify the potential life cycle energy savings possible compared to the original building. The study showed that significant life cycle energy savings are possible through the modelling of individual building elements for the case study building. While these findings relate to a very specific case, this study demonstrates the application of a model for optimising building life cycle energy performance that may be applied more broadly during early-stage building design to optimise life cycle energy performance.

The importance of sand albedo for the thermal conditions on sea turtle nesting beaches

At Ascension Island and Cyprus, major nesting areas for green turtles (Chelonia mydas) in the Atlantic and Mediterranean, respectively, visual inspection shows some beaches are light in colour while others are darker. We objectively measured the albedo of the sand on different beaches, i.e. the percentage of the incident solar radiation that was reflected from the sand surface. At sites where albedo was recorded, we also measured the temperature of the sand at nest depths. At both rookeries, the sand temperature was markedly higher on darker beaches due to greater absorption of the incident solar radiation over the diurnal cycle. Temperature loggers buried at nest depths revealed seasonal changes in temperature on both islands, but showed that the lowest temperatures found on the darker beaches rarely dropped below the highest temperatures on the lighter beaches. Sea turtles exhibit temperature-dependent sex determination. Since sand albedo is a major avenue for the production of a range of incubation temperatures on both islands, it will also have profound implications for hatchling sex ratios. In comparison with both Ascension Island and Cyprus, for samples collected from sea turtle rookeries around the world there was an even greater range in sand albedo values. This suggests that sand albedo, a factor that has previously received little consideration, will have profound implications for nest temperatures, and hence hatchling sex ratios, for other populations and species.

A comprehensive framework for assessing the life-cycle energy of building construction assemblies

Building environmental design typically focuses on improvements to operational efficiencies such as building thermal performance and system efficiency. Often the impacts occurring across the other stages of a building's life are not considered or are seen as insignificant in comparison. However, previous research shows that embodied impacts can be just as important. There is limited consistent and comprehensive information available for building designers to make informed decisions in this area. Often the information that is available is from disparate sources, which makes comparison of alternative solutions unreliable. It is also important to ensure that strategies to reduce environmental impacts from one life cycle stage do not come at the expense of an increase in overall life-cycle impacts. A consistent and comprehensive framework for assessing and specifying building assemblies for enhanced environmental outcomes does not currently exist. This article presents the initial findings of a project that aims to establish a database of life cycle energy requirements for a broad range of construction assemblies, based on a comprehensive assessment framework. Life cycle energy requirements have been calculated for eight residential construction assemblies integrating an innovative embodied energy assessment technique with thermal performance modelling and ranked according to their performance. © #2010 Earthscan ISSN: 0003-8628.