A solar collector with the absorber divided by rectangular slots

A new solar absorber structure has been proposed and studied in this paper. The metal tubes running perpendicular to a set of parallel rectangular metal fins make the solar absorber with rectangular slots. Studies on the collector were theoretically carried out in the aspects of heat transfer, thermodynamics and . hydrodynamics. The calculating methods for calculating fin efficiency F and efficiency factors of the collector F' were obtained. The results showed that the new solar collector would have the higher efficiency and better performance at higher fluid temperature than that of the traditional flat-plate collectors. A collector prototype with the new structure was built and tested. The testing results agree with our theoretical results.

Analysis of the current distribution in an aluminum electrolysis cell with copper collector-bar cathode assembly

Understanding the magneto-hydrodynamic forces generated due to the external magnetic field and current density distribution within the cell (current in cell linings) is important in the optimization of cell dynamics. It is well documented that these factors play a crucial role in establishing the metal-pad stability of the cell. Conventional cells use the cathode-collector-bar assembly to carry the current through molten aluminium, the cathode and the steel collector-bar to nearest external bus. The electrical conductivity of the steel is so poor relative to the molten aluminium that the outer third of the collector bar carries the maximum load, which in turn increases the horizontal components of the current within the cell. Previous studies have modelled improvement in the cell instability through external magnetic compensation by redistributing current in the cathode busbar. Very little to date has been published on work to improve the current distribution within the cell. In this work, the current distribution in an aluminium electrolysis cell with copper collector-bar was predicted using finite element modelling. A 2D cross-section of a commercial cell was used under steady conditions of electrical fields in anode, electrolyte, molten aluminium and copper cathode-assembly. Different shapes and sizes of the cathode assembly are also considered to optimise the distribution of current throughout the cathode lining. The findings indicated that the copper-bar of similar size to steel could save voltage up to 150 mV. There is a reduction of more than 70% in peak current density value due to the copper inserts. The predicted trends of current distribution show a good agreement with previously published data.

Designing a low cost solar collector system for process industry applications

New Zealand is a large producer and processor of primary products and has a climate with high levels of solar radiation. However, the use of solar energy for heating and cooling in the processing industries has received limited attention.
For this study, the design of a low cost solar collector is analysed and discussed. Furthermore, the methods for integrating the collector into water heating and cooling systems in a hypothetical processing environment are examined. An F-Chart analysis is used to simulate the performance of large-area arrays of the solar collector and to determine its potential contribution to heating and cooling loads.
The study shows that for a storage-based system, the contribution of solar energy is determined mainly by the collector area to storage volume ratio. It is suggested that this low cost collector could make a significant contribution to energy use in processing plants and may be an attractive future technology.

re.reading: Pound at the Lenton Parr Library

Catalogue and essays to accompany re.reading - Pound at the Lenton Parr Music, Visual and Performing Arts Library, an exhibition run in conjunction with Melbourne Rare Book Week 2014. Essay. Project Manager Georgina Binns. Essay entitled The Call of Patrick Pound written by Chris Bond.

Spring 1883: Art Fair at the Windsor Hotel

Exhibition of three works by Patrick Pound as part of the Spring 1883 exhibition. Art works entitled: 'Spring Street' a collection of vintage postcards each showing the street the exhibition hotel is located on, the 'Collector' a collection of John Fowles' novel the 'Collector' in numerous editions, and 'The Apartment' a collage of a derelict apartment block. These works were exhibited by Hamish McKay Gallery.The brainchild of Melbourne gallerists Vasili Kaliman (Station), Geoff Newton (Neon Parc), and Vikki McInnes (Sarah Scout Presents), SPRING 1883, the exhibition took place at Melbourne’s historic Hotel Windsor from August 14-17, 2014.The fair drew on the traditions of New York’s hotel-based Gramercy Park Fair and presented the best of contemporary art practice from Australia, New Zealand, Europe, and the United States.“Providing a boutique site for dialogue and interaction between galleries, artists and collectors, the fair will create a new energy for the contemporary art market in Australia”

A medium-temperature solar thermal power system and its efficiency optimisation

This paper firstly expounds that the reheat-regenerative Rankine power cycle is a suitable cycle for the parabolic trough collector, a popular kind of collector in the power industry. In a thermal power cycle, the higher the temperature at which heat is supplied, the higher the efficiency of the cycle. On the other hand, for a given kind of collector at the same exiting temperature, the higher the temperature of the fluid entering the collector, the lower the efficiency of the collector. With the same exiting temperature of the solar field and the same temperature differences at the hottest end of the superheater/reheater and at the pinch points in the heat exchangers (e.g., the boiler) in the cycle, the efficiencies of the system are subject to the temperature of the fluid entering the collector or the saturation temperature at the boiler. This paper also investigates the optimal thermal and exergetic efficiencies for the combined system of the power cycle and collector. To make most advantage of the collector, the exiting fluid is supposed to be at the maximum temperature the collector can harvest. Hence, the thermal and exergetic efficiencies of the system are related to the saturation temperature at the boiler here.

Disk-electrospinning of PVA nanofibres

In this study, we demonstrated that a thin aluminium disk can be used as nozzle to electrospin PVA nanofibres on a large-scale. A schematic of this electrospinning system and a SEM image of as-spun PVA nanofibers are shown in Figure 1. The lower part of the disk is inside a bath containing the polymer solution, which is connected to a high voltage powder supply. During electrospinning, the disk rotates and picks up a thin layer of electrically charged PVA solution. A large number of fibres are then electrospun simultaneously from two sides of tile disk and deposited on the electrode collector.
With the small prototype unit we used, the fibre production rate can be as high as 6.0 which is about 270 times higher than that of a corresponding normal needle electrospinning system (0.022g/hr). The effects of appliedb voltage, the distance between the disk nozzle and collector, and PVA concentration on the fibre morphology were examined. The dependency of fibre diameter on the PVA concentration showed a similar trend to that for a conventional electrospinning system using a syringe needle nozzle, but the diameter distribution was wider for the disk electrospun fibres in this study.
The profiles of electric field strength in disk electrospinning showed considerable dependence on the disk thickness, with a thin disk exhibiting similar electric field profile to
that of a needle electrospinning system, but a thick disk (cylinder) exhibiting levelled electric field between the disk and the collector. PVA nanofibres electrospun from disk electrospinning were compared to that electrospun from syringe needle and metal cylinder nozzles.

Solar energy use for energy savings in dairy processing plants

New Zealand is one of the world’s largest producers of dairy products and has a climate with high levels of solar radiation; however, the use of solar energy in the dairy processing industry has received limited attention. An examination of historical records found that the annual peak in New Zealand milk production and processing occurs at a time when solar radiation levels are increasing markedly. An F-Chart analysis was used to simulate the performance of large-area arrays of solar collectors and to determine their suitability for heating and cooling in a dairy processing environment. For the study four types of solar collectors were analysed: glazed flat plates, evacuated tubes, evacuated tubes with CPC reflectors and a building-integrated solar collector under development at the University of Waikato (UoW). It was found that of these echnologies, both flat plate and evacuated tubes with CPC reflectors could make useful heating and cooling contributions. Furthermore, the solar fraction was determined mainly by the collector area to storage volume ratio. Finally, it was found that the UoW building-integrated solar collector could make a significant contribution to energy use in dairies and may be an attractive future technology for the industry.

Convection suppression in an attic shaped enclosure

In recent times there has been growing interest in the integration of solar collectors, for water heating, into the façade of buildings. However, the design methodology of these devices remains largely the same as typical “stand-alone” collectors. As such it is still common for materials with a high thermal resistance to be used for insulating the rear surface of these collectors.

Unlike a “stand-alone” solar collector that is exposed to the atmosphere at all faces; a building integrated system allows the opportunity for air to act as an insulator at the rear surface of the solar collector. The use of convection suppression devices has been widely discussed in the literature as a means of reducing natural convection heat loss from the front surface of glazed solar collectors. However in this study the use of baffles in an attic was examined as a means of suppressing heat loss by natural convection from the rear surface of a roof-integrated solar collector. The aim of the study was to examine whether the use of baffles would allow the cost of building integrated collectors to be reduced by removing the cost of insulating material.

To determine the effect of baffles in the attic space at the rear surface of the collector, a 3-dimensional triangular cross sectioned enclosure with a vertical aspect ratio of 0.5 and a horizontal aspect ratio of 3.3 was modelled. The flow patterns and heat transfer in the enclosure were determined for Grashof Numbers in the range of 106 to 107 using a commercially available finite volume CFD solver.
It was found that the use of a single adiabatic baffle mounted vertically downwards from the apex, and extending the length of the enclosure, would alter the flow such that the heat transfer due to natural convection was reduced with respect to the length of the baffle.

Furthermore, it was observed that a series of convection cells, not previously reported in the literature, appeared to exist along the length of the enclosure. As such, it may be possible to derive additional benefit in reducing the heat transfer by adding lateral baffles in addition to the single longitudinal baffle modelled in this study.

Needleless electrospinning : developments and performances

Electrospinning technique has attracted a lot of interests recently, although it was invented in as early as 1934 by Anton (Anton, 1934). A basic electrospinning setup normally comprises a high voltage power supply, a syringe needle connected to power supply, and a counter-electrode collector as shown in Fig. 1. During electrospinning, a high electric voltage is applied to the polymer solution, which highly electrifies the solution droplet at the needle tip (Li & Xia, 2004). As a result, the solution droplet at the needle tip receives electric forces, drawing itself toward the opposite electrode, thus deforming into a conical shape (also known as “Taylor cone” (Taylor, 1969)). When the electric force overcomes the surface tension of the polymer solution, the polymer solution ejects off the tip of the “Taylor cone” to form a polymer jet. The charged jet is stretched by the strong electric force into a fine filament. Randomly deposited dry fibers can be obtained on the collector due to the evaporation of solvent in the filament. There are many factors affecting the electrospinning process and fiber properties, including polymer materials (e.g. polymer structure, molecular weight, solubility), solvent (e.g. boiling point, dielectric properties), solution properties (e.g. viscosity, concentration, conductivity, surface tension), operating conditions (e.g. applied voltage, collecting distance, flow rate), and ambient environment (e.g. temperature, gas environment, humidity).

Effect of nozzle polarity and connection on electrospinning of polyacrylonitrile nanofibers

In this study, two power supplies having positive/ground and negative/ground electrode output ends were used separately for electrospinning of polyacrylonitrile nanofibers. Depending on type of power supply and electrode connection, electrospinning led to different fiber diameters and deposition areas. The nozzle was connected to a high voltage end while the collector was grounded. Regardless of power supply used, finer fibers with a larger deposition area were obtained, compared to that using the same setup but with a reverse electrode connection. With an increase in the applied voltage, fiber deposition area, and productivity increased for all electrode connections. Grounded nozzles provide much better control over fiber deposition than the reverse electrode connections. Finite element modeling was used to analyze the electric field profile in the electrospinning zone. It was revealed that high electric intensity was mainly located in the part that was charged with a high voltage electrode, which could explain the differences in fiber diameter and deposition area.

Effects of baffles on flow distribution in an electrostatic precipitator (ESP) of a coal based power plant

Electrostatic Precipitators (ESP) are the most reliable and industrially used control devices to capture fine particles for reducing exhaust emission. Its efficiency is 99% or more. However, capturing submicron particles which are hazardous is still a problem as it involves complex flow phenomena and ESP design limitations. In this study, the effect of baffles on flow distribution inside the ESP is investigated computationally. Baffles are expected to increase the residence time of flue gas which helps to collect more particles into the collector plates, and hence increase the collection efficiency of an ESP. Besides, the placement of a baffle is likely to cause swirling of flue gas and hence sub-micron particles move towards the collector plate due to eccentric and electrostatic force. Therefore, the effects of position, shape and thickness of the baffles on collection efficiency which are also important for ESP design are reported in this study. The fluid flow distribution has been modelled using computational fluid dynamics (CFD) software Fluent and the result and outcome are presented and discussed. The result shows that baffles have significant influence on fluid flow pattern and the efficiency of ESP.

Application of the Hottel-Whillier equations to the analysis of a building integrated photovoltaic/thermal solar collector

The idea of combining photovoltaic and solar thermal collectors (PVT collectors) to provide electrical and heat energy is not new, however it is an area that has received only limited attention. With concern growing over energy sources and their usage, PVTs have become an area receiving more attention. Although PVTs are not as prevalent as solar thermal systems, the integration of photovoltaic and solar thermal collectors into the walls or roofing structure of a building could provide greater opportunity for the use of renewable solar energy technologies in domestic, commercial and industrial applications. As such, the design of a novel building integrated photovoltaic/thermal (BIPVT) solar collector is theoretically analysed through the use of a modified Hottel-Whillier model. The thermal and electrical efficiency under a range of conditions are subsequently determined and results showing how key design parameters influence the performance of the BIPVT system are presented.

The rising prevalence of diabetes and impaired glucose tolerance : the Australian diabetes, obesity and lifestyle study

OBJECTIVE—To determine the population-based prevalence of diabetes and other categories of glucose intolerance (impaired glucose tolerance [IGT] and impaired fasting glucose [IFG]) in Australia and to compare the prevalence with previous Australian data.

RESEARCH DESIGN AND METHODS—A national sample involving 11,247 participants aged >=25 years living in 42 randomly selected areas from the six states and the Northern Territory were examined in a cross-sectional survey using the 75-g oral glucose tolerance test to assess fasting and 2-h plasma glucose concentrations. The World Health Organization diagnostic criteria were used to determine the prevalence of abnormal glucose tolerance.

RESULTS—The prevalence of diabetes in Australia was 8.0% in men and 6.8% in women, and an additional 17.4% of men and 15.4% of women had IGT or IFG. Even in the youngest age group (25–34 years), 5.7% of subjects had abnormal glucose tolerance. The overall diabetes prevalence in Australia was 7.4%, and an additional 16.4% had IGT or IFG. Diabetes prevalence has more than doubled since 1981, and this is only partially explained by changes in age profile and obesity.

CONCLUSIONS—Australia has a rapidly rising prevalence of diabetes and other categories of abnormal glucose tolerance. The prevalence of abnormal glucose tolerance in Australia is one of the highest yet reported from a developed nation with a predominantly Europid background.

Abbreviations: 2hPG, 2-h plasma glucose • AusDiab, Australian Diabetes, Obesity and Lifestyle Study • CD, Census Collector District • FPG, fasting plasma glucose • IFG, impaired fasting glucose • IGT, impaired glucose tolerance • KDM, known diabetes mellitus • NDM, newly diagnosed diabetes mellitus • OGTT, oral glucose tolerance test • WHO, World Health Organization

The effect of colour on the thermal performance of building integrated solar collectors

The use of solar collectors with coloured absorbers for water heating is an area of particular interest when considering their integration with buildings. By matching the absorber colour with that of the roof or façade of the building, it is possible to achieve an architecturally and visually pleasing result. Despite the potential for the use of coloured absorbers, very little work has been undertaken in the field.

In this study, the thermal performance of a series of coloured (ranging from white to black), building integrated solar collectors for water heating was examined both theoretically and experimentally. Subsequently, the annual solar fraction for typical water heating systems with coloured absorbers was calculated. The results showed that coloured solar collector absorbers can make noticeable contributions to heating loads. Furthermore, although their thermal efficiency is lower than highly developed selective coating absorbers, they offer the advantage of improved aesthetic integration with buildings.