Characterization of microstructures and tensile properties of TRIP-aided steels with different matrix microstructure

Three different heat treatment processes have been proposed as a fundamental method to produce three kinds of TRIP-aided steels with polygonal ferritic matrix (F-TRIP), bainitic matrix (B-TRIP) and martensitic matrix (M-TRIP) in a newly designed low alloy carbon steel. By means of dilatometry study and detailed characterization, the relationships among transformation, microstructure and the resulting mechanical behavior were compared and analyzed for the three cases. The work hardening of the samples was evaluated by calculating the instantaneous n value as a function of strain. The M-TRIP sample exhibits the highest strength with the highest work hardening rate at low strains and subsequent rapid descending at high strains. In contrast, the B-TRIP sample has relatively high continuously constant work hardening behavior over strain levels greater than 0.067. The difference in work hardening behavior corresponds directly to the rate of the retained austenite-martensitic transformation during straining, which can be attributed to the carbon content, the morphology of the retained austenite and the matrix microstructure in the respective TRIP-aided samples. © 2014 Elsevier B.V.

Improving wool/polyester yarn quality by transposal spinning with movable balloon control ring

To improve yarn quality in ring spinning frame, this paper examines transposal spinning with the movable balloon control ring. The left-transposal spinning and the right-transposal spinning were experimented to spin two yarns; after installing the movable balloon control ring, the two methods were respectively used to spin two other yarns again. All the experiments were on the same ring frame and the raw material was wool/polyester blend roving with a ration of 30/70. The main quality indexes of the four yarns were tested and analyzed, including hairiness, tensile property, evenness and usual faults. The results show that the yarn spun by the left-transposal spinning has a better quality than the right-transposal spinning, and after adding the movable balloon control ring, the improvement of yarn hairiness strength and evenness, as well usual faults, is very obvious. So, in the advantage of transposal spinning, the method of installing the movable balloon control ring can improve some deteriorative problems and make yarn quality better. In addition, the method gives new insight into energy efficiency. The research in this field in on the way and the result is in accord with the Low-carbon Economy.

Functionalised roving for structural health monitoring of composites

Here, we investigated photochromic glass fibre threads produced with the sol-gel coating technique and used it as sewing threads to produce stitched glass-polypropylene composites. The possibility of making sol-gel photochromic glass fibre threads, the morphology of the glass fibre thread and the tensile property of glass fibre sewing threads before and after sol-gel treatment have been studied in this work. The photochromic glass fibre thread was successfully stitched into glass-polypropylene composites as sewing threads and showed an efficient and effective response to UV light. Our results indicate that sol-gel coating is an efficient way to produce photochromic glass fibre. In addition, the sol-gel coating does not significantly affect the tensile performance of the glass fibre.

Microstructure-property relationship of the high strength low alloy steels during tensile testing at high strain rates

Positive The influence of strain-rate on the room temperature mechanical properties of the Dual-Phase and Transformation Induced Plasticity (TRIP) steels was investigated.The results showed that both the plastic strain, and strength properties increased with increasing strain rates at high strain rates.At strain rates lower than approximateil 1s ~ (-1) the properties no longer have an advantageous proportionality to strain rate and remain strain rate neutral.Possible explanations are offered for trends exhibited, in terms of thermal and athermal considerations, in relation to the respective microstructures of the two steels

Effect of initial processing on the microstructure-property relationships in bake-hardened C-Mn-Si TRIP steels

The effect of pre-straining (PS) and bake-hardening (BH) on the microstructure and mechanical properties has been studied in C-Mn-Si TRansformation Induced Plasticity (TRIP) steels after: (i) thermomechanically processing (TMP) and (ii) intercritical annealing. The steels were characterised before and after PS/BH by transmission electron microscopy (TEM), X-ray diffraction (XRD), and tensile tests. The main microstructural differences were the higher volume fraction of bainite and more stable retained austenite in the TMP steel. This led to a difference in the strain-hardening behavior before and after BH treatment. The higher dislocation density in ferrite and formation of microbands in the TMP steel after PS and the formation of Fe3C carbides between the bainitic ferrite laths during BH for both steels also affected the strain-hardening behavior. However, both steels after PS/BH treatment demonstrated an increase in the yield and tensile strength.

Effect of alloying elements on the microstructure property relationship in thermomechanically processed C-Mn-Si TRIP steels

The effect of additions of Nb, Al and Mo to Fe-C-Mn-Si TRIP steel on the final microstructure and mechanical properties after simulated  thermomechanical processing (TMP) has been studied. The laboratory simulations of discontinuous cooling during TMP were performed using a hot rolling mill. All samples were characterised using optical microscopy and image analysis. The volume fraction of retained austenite was ascertained using a heat tinting technique and X-ray diffraction measurements. Room temperature mechanical properties were determined by a tensile test. From this a comprehensive understanding of the structural aspect of the bainite transformation in these types of TRIP steels has been developed. The  results have shown that the final microstructures of thermomechanically processed TRIP steels comprise 50 % of polygonal ferrite, 7 - 12 % of retained austenite, non-carbide bainitic structure and martensite. All steels exhibited a good combination of ultimate tensile strength and total elongation. The microstructure-property examination revealed the relationship between the composition of TRIP steels and their mechanical properties. It has been shown that the addition of Mo to the C-Si-Mn-Nb TRIP steel increases the ultimate tensile strength up to 1020 MPa. The stability of the retained austenite of the Nb-Mo steel was degraded, which led to a decrease in the elongation (24 %). The results have demonstrated that the addition of Al to C-Si-Mn-Nb steel leads to a good combination of strength (∼ 940 MPa) and elongation (∼ 30 %) due to the formation of refined acicular ferrite and granular bainite structure with ∼7 - 8 % of stable retained austenite. Furthermore, it has been found that the addition of Al increases the volume fraction of bainitic ferrite laths. The investigations have shown an interesting result that, in the Nb-Mo-Al steel, Al has a more pronounced effect on the microstructure in comparison with Mo. It has been found that the bainitic structure of the Nb-Mo-Al steel appears to be more granular than in the Nb-Mo steel. Moreover, the volume fraction of the retained austenite increased (12 %) with decreasing bainitic ferrite content. The results have demonstrated that this steel has the best mechanical properties (1100 MPa and 28 % elongation). It has been concluded that the combined effect of Nb, Mo, and Al addition on the dispersion of the bainite, martensite and retained austenite in the ferrite matrix and the morphology of these phases is different than effect of Nb, Mo and Al, separately.

Effect of alloying elements on the microstructure-property relationship in thermomechanically processed C-Mn-Si TRIP steels

The effect of additions of Nb, Al and Mo to Fe-C-Mn-Si TRIP steel on the final microstructure and mechanical properties after simulated thermomechanical processing (TMP) has been studied. The laboratory simulations of discontinuous cooling during TMP were performed using a hot rolling mill. All samples were characterised using optical microscopy and image analysis. The volume fraction of retained austenite was ascertained using a heat tinting technique and X-ray diffraction measurements. Room temperature mechanical properties were determined by a tensile test. From this a comprehensive understanding of the structural aspect of the bainite transformation in these types of TRIP steels has been developed. The results have shown that the final microstructures of thermomechanically processed TRIP steels comprise 50 % of polygonal ferrite, 7 - 12 % of retained austenite, non-carbide bainitic structure and martensite. All steels exhibited a good combination of ultimate tensile strength and total elongation. The microstructure-property examination revealed the relationship between the composition of TRIP steels and their mechanical properties. It has been shown that the addition of Mo to the C-Si-Mn-Nb TRIP steel increases the ultimate tensile strength up to 1020 MPa. The stability of the retained austenite of the Nb-Mo steel was degraded, which led to a decrease in the elongation (24 %). The results have demonstrated that the addition of Al to C-Si-Mn-Nb steel leads to a good combination of strength (∼ 940 MPa) and elongation (∼ 30 %) due to the formation of refined acicular ferrite and granular bainite structure with ∼7 - 8 % of stable retained austenite. Furthermore, it has been found that the addition of Al increases the volume fraction of bainitic ferrite laths. The investigations have shown an interesting result that, in the Nb-Mo-Al steel, Al has a more pronounced effect on the microstructure in comparison with Mo. It has been found that the bainitic structure of the Nb-Mo-Al steel appears to be more granular than in the Nb-Mo steel. Moreover, the volume fraction of the retained austenite increased (12 %) with decreasing bainitic ferrite content. The results have demonstrated that this steel has the best mechanical properties (1100 MPa and 28 % elongation). It has been concluded that the combined effect of Nb, Mo, and Al addition on the dispersion of the bainite, martensite and retained austenite in the ferrite matrix and the morphology of these phases is different than effect of Nb, Mo and Al, separately.

Electrospun single-walled carbon nanotube/polyvinyl alcohol composite nanofibers : structure-property relationships

Polyvinyl alcohol (PVA) nanofibers and single-walled carbon nanotube (SWNT)/PVA composite nanofibers have been produced by electrospinning. An apparent increase in the PVA crystallinity with a concomitant change in its main crystalline phase and a reduction in the crystalline domain size were observed in the SWNT/PVA composite nanofibers, indicating the occurrence of a SWNT-induced nucleation crystallization of the PVA phase. Both the pure PVA and SWNT/PVA composite nanofibers were subjected to the following post-electrospinning treatments: (i) soaking in methanol to increase the PVA crystallinity, and (ii) cross-linking with glutaric dialdehyde to control the PVA morphology. Effects of the PVA morphology on the tensile properties of the resultant electrospun nanofibers were examined. Dynamic mechanical thermal analyses of both pure PVA and SWNT/PVA composite electrospun nanofibers indicated that SWNT–polymer interaction facilitated the formation of crystalline domains, which can be further enhanced by soaking the nanofiber in methanol and/or cross-linking the polymer with glutaric dialdehyde.

Tensile behaviour of wool fabric as a function of fabric pH

Wool fabric extensibility under a 5 N/cm load was observed to be greatest at the wool isoelectric point of pH 4.8 and lower at both pH 2.1 and pH 7.2. The impact of pH on fabric extensibility is similar to the variation in fabric hygral expansion previously observed. Fabric stress-strain curves at different pHs show that for a given fabric extension level, the work required to stretch a fabric was less at pH 2.1 than at pH 4.8. These results confirm the fact that the strength of wool fabric is at a maximum when the pH of the fibres is close to the isoelectric point.

Effect of tensile pre-strain on bending and unloading of automotive steels

In recent years, advanced high strength steels (AHSS) have been used in a wide range of automotive applications; they may have property variations through the thickness and the properties may also be dependent of prior processing including pre-straining. In order to model forming processes precisely using, for example, finite element analysis, it is important that material input data should adequately reflect these effects. It is known that shape defects in roll forming are related to small strains in material that has undergone prior deformation in a different strain path. Much research has already been performed on the change in the Young’s Modulus once a steel sheet has been plastically deformed,however many of these tests have only been conducted using tensile testing, and therefore may not take into account differences in compressive and tensile unloading. This research investigates the effect of tensile pre-straining on bending behaviour for various types of material;in bending, one half of the sheet will load and unload in compression and hence experience deformation under a reversed stress. Four different materials were pre-strained in tension with 1%, 3%, 7%, 11% and 25% elongation. Using a free bending test, moment curvature diagrams were obtained for bending and unloading. The results showed that the characteristics of the moment curvature diagram depended on the degree of pre-straining; more highly strained samples showed an earlier elastic-plastic transformation and a decreased Young's Modulus during unloading. This was compared to previous literature results using only tensile tests. Our results could influence the modeling of springback in low tension sheet operations, such as roll forming.

Structure-property relationships in nylon 6 nanocomposites based on octaphenyl-, dodecaphenyl-POSS, montmorillonite, and their combinations

Binary and ternary nanocomposites were produced by incorporating, via melt compounding, two types of octa-and dodecaphenyl substituted polyhedral oligomeric silsesquioxanes (POSS), montmorillonite (MMT), and combinations of POSS with MMT into nylon 6. The tensile, flexural, and dynamic thermo-mechanical properties of these materials were characterized and their structure-property relationships discussed. The results show that the losses in ductility and toughness experienced after inclusion of MMT into nylon 6 can be balanced out by co-mixing MMT with the dodecaphenyl- POSS to produce a ternary nanocomposite. This trend however was less pronounced in the ternary MMT/octaphenyl-POSS system. Analysis of the microstructure organization in these materials using XRD and SEM sheds some light on understanding the differences in behavior. Both types of POSS particles mixed alone in nylon 6 were found to be polydisperse (500 nm to a few microns in size) and locally aggregated, yielding materials with similar mechanical performance. The co-mixing of MMT with the octaphenyl- POSS served to break down the POSS crystal aggregates, enhancing their micro-mechanical reinforcing action. On the other hand, the POSS crystals were not affected in the MMT/dodecaphenyl-POSS system, which led to improving their toughening ability.