Characteristics of the contraction twins formed close to the fracture surface in Mg-3A1-1Zn alloy deformed in tension

Characteristics of the “contraction” twins, formed close to the fracture surface in Mg–3Al–1Zn alloy deformed in tension approximately perpendicular to the grain c-axes, are investigated using transmission electron microscopy. The grain c-axis contractions were largely accommodated by {1011}-{1012} source double-twins in a variant characterized by 38° ⟨1210⟩ source twin/matrix misorientation in conjunction with dislocation slip. A possible interpretation of the observed preference for this variant formation is given and some crystal plasticity modelling is performed to elucidate the matter.

A nanoscale SQUID operating at high magnetic fields

A washer-free Nb nanoSQUID has been developed for measuring magnetization changes from nanoscale objects. The SQUID loop is etched into a 250 nm wide Au/Nb bilayer track and the diameter of the SQUID hole is ~ 70 nm. In the presence of a magnetic field perpendicular to the plane of the SQUID, vortex penetration into the 250 nm wide track can be observed via the critical current–applied field characteristic and the value at which vortex first penetrates is consistent with the theoretical prediction. Upon removing the applied field, the penetrated vortices escape the track and the critical current at zero field is restored.

Numerical modeling and analysis for forming process of dual-phase 980 steel exposed to infrared local heating

A recent experiment confirmed that the infrared (IR) local heating method drastically reduces springback of dual-phase (DP) 980 sheets. In the experiment, only the plastic deformation zone of the sheets was locally heated using condensed IR heating. The heated sheets were then deformed by V-bending or 2D-draw bending. Although the experimental observation proved the merit of using the IR local heating to reduce springback, numerical modeling has not been reported. Numerical modeling has been required to predict springback and improve the understanding of the forming process. This paper presents a numerical modeling for V-bending and 2D-draw bending of DP 980 sheets exposed to the IR local heating with the finite element method (FEM). For describing the thermo-mechanical behavior of the DP 980 sheet, a flow stress model which includes a function of temperature and effective plastic strain was newly implemented into Euler-backward stress integration method. The numerical analysis shows that the IR local heating reduces the level of stress in the deformation zone, although it heats only the limited areas, and then it reduces the springback. The simulation also provides a support that the local heating method has an advantage of shape accuracy over the method to heat the material as a whole in V-bending. The simulated results of the springback in both V-bending and 2D-draw bending also show good predictions.

Numerical modeling of the dynamic tensile behavior of irregular fibers

Most fibers are irregular, and they are often subjected to rapid straining during mechanical processing and end-use applications. In this paper, the effect of fiber dimensional irregularities on the dynamic tensile behavior of irregular fibers is examined, using the finite element method (FEM). Fiber dimensional irregularities are simulated with sine waves of different magnitude (10%, 30% and 50% level of diameter variation). The tensile behavior of irregular fibers is examined at different strain rates (333%/sec, 3,333%/sec and 30,000%/sec). The breaking load and breaking extension of irregular fibers at different strain rates are then calculated from the finite element model. The results indicate that strain rate has a significant effect on the dynamic tensile behavior of an irregular fiber, and that the position of the thinnest segment along the fiber affects the simulation results markedly. Under dynamic conditions, an irregular fiber does not necessarily break at the thinnest segment, which is different from the quasi-static results.

Numerical modeling of dual phase microstructure behavior under deformation conditions on the basis of digital material representation

Development of a digital material representation (DMR) model of dual phase steel is presented within the paper. Subsequent stages involving generation of a reliable representation of microstructure morphology, assignment of material properties to component phases and incorporation of the model into the commercial finite element software are described within the paper. Different approaches used to recreate dual phase morphology in a digital manner are critically assessed. However, particular attention is placed on innovative identification of phase properties at the micro scale by using micro-pillar compression tests. The developed DMR model is finally applied to model influence of micro scale features on failure initiation and propagation under loading conditions.

Numerical modeling of interactions between a macro-crack and a cluster of micro-defects

The interactions between a macro-crack and a cluster of micro-defects are studied numerically by using a series of special finite elements each containing a defect. These special finite elements, which contain defects such as holes, cracks, and inhomogeneities, are developed based on the hybrid displacement, complex potential and conformal mapping techniques. These hybrid-type elements can be used together with the conventional finite elements without any difficulty. Thus, simple finite element models can be devised to study the interactions between a macro-crack and a cluster of micro-defects. In this paper, the mathematical and finite element modeling procedures for the study of the above-mentioned problems are presented.

The structural events approach- A "better" way to understand long-term change in trade union structure: the Australian story (1986-96)

Traditional studies of long-term change in trade union structure have predominantly focused on aggregate trends in union merger activity in constructing explanations of change. Using the Australian trade union movement as an example, this article argues that our understanding of the long-term change in the external structure of trade unions would be better served by a structural events approach (Waddington, 1995) that examines the incidence of union formations, dissolutions, and breakaways, in addition to that of union mergers. In doing so, this article presents new data on structural change in the Australian trade union movement between 1986 and 1996, and explains the additional contribution made by union dissolutions and union formations to the reductionist effects of the merger wave that dominated these years.

Hail to the chief! Leadership and structural change in the level of consensus on the High Court of Australia

This article identifies structural breaks in dissenting and single opinions on the High Court of Australia and uses a recent method proposed by Caporale and Grier (2002) to examine the effect of leadership on variations in the dissent rate between 1904 and 2001. Although there has been much speculation about the effectiveness of different Chief Justices in obtaining consensus on the Court, to this point most of the evidence has been anecdotal. Our main findings are that the structural breaks that we identify coincide with major turning points in the leadership of the Court and that leadership has been important in explaining variations in the proportion of dissenting opinions on the Court.

A non-darcian numerical modeling in domed enclosures filled with heat-generating porous media

Numerical study of the natural-convection flow and heat transfer in a dome-shaped, heat-generating, porous enclosure is considered. The general conic equation for the top dome is used to consider various conical top sections such as circular, elliptical, parabolic, and hyperbolic. The individual effect of fluid Rayleigh, Darcy, and heat-generating parameters on flow patterns and heat transfer rates are analyzed and presented. The predicted results show that the heat-generating parameter has the most significant contribution toward the growth of bicellular core flow. Moreover, there is significant change in temperature distribution in comparison to rectangular enclosures, due to the existence of the domed-shape top adiabatic cover. The results also show that, regardless of Darcy and Rayleigh values, a flat adiabatic top cover tends to yield the highest value of Nusselt number, followed by circular, elliptical, parabolic, and hyperbolic top covers, respectively.

Understanding response surface optimisation to the modeling of Astaxanthin extraction from a novel strain Thraustochytrium sp. S7

A fast growing, highly orange color pigmented strain of Thraustochytrids was isolated from New Zealand marine waters. This strain showed efficient utilization of glycerol as carbon source and produced significant amount of cell dry biomass (2.08gL-1), TFA (30.15% of dry cell weight), DHA (27.83% of TFA) and astaxanthin (131.56μgg-1). Astaxanthin is the dominant constituent in the carotenoid profile of Thraustochytrium sp. S7 and is an important antioxidant. Different cell disruption methods were applied for efficient astaxanthin extraction. Mechanical disruption of cells via ultrasonication resulted in the highest astaxanthin yield, from 26.78±1.25μgg-1 to 156.07±4.16μgg-1. Optimization of ultrasonication process using response surface methodology resulted into significant decrease in lysis time from 30min to 10min. This strain can be used for concurrent production of lipids and high value co-products such as DHA and astaxanthin.

Sensitivity of the final properties of tailored hot stamping components to the process and material parameters

The final mechanical properties of hot stamped components are affected by many process and material parameters due to the multidisciplinary nature of this thermal-mechanical-metallurgical process. The phase transformation, which depends on the temperature field and history, determines the final microstructure and consequently the final mechanical properties. Tailored hot stamping parts - where the cooling rates are locally chosen to achieve structures with graded properties - has been increasingly adopted in the automotive industry. In this case, the robustness of final part properties is more critical than in the conventional hot stamping parts, where the part is fully quenched. In this study, a wide range of input parameters in a generalized hot stamping model have been investigated, examining the effect on the temperature history and resulting final material properties. A generic thermo-mechanical finite element model of hot stamping was created and a modified phase transformation model, based on Scheil's additive principle, has been applied. The comparison between modeling and experiments shows that the modified phase transformation model coupled with the incubation time provides higher accuracy on the simulation of transformation kinetics history. The robustness of four conditions relevant to tailored hot stamping was investigated: heated tooling (with low and high tool conductance), air cooling, and conventional hot stamping. The results show the high robustness of the conventional hot stamping compared to tailored hot stamping, with respect to the stamped component's final material properties (i.e. phase fraction and hardness). Furthermore, tailored hot stamping showed higher robustness when low conductivity tools are used relative to high conductivity tools.

Numerical modeling of vertical earth pipe cooling system for hot and humid subtropical climate

Energy crisis is one of the major problems facing the progress of human society. There are several energy-efficient technologies that can be applied to save energy and make a sustainable environment. Passive air cooling of earth pipe cooling technology is one of them to reduce the energy consumption for hot and humid subtropical climates. The technology works with a long buried pipe with one end for intake air and the other end for providing air cooled by soil to the desired space such as residential, agricultural, or industrial buildings. It can be an attractive economical alternative to conventional cooling since there are no compressors or any customary mechanical unit. This chapter reports the performance of a vertical earth pipe cooling system for a hot and humid subtropical climatic zone in Queensland, Australia. A series of buried pipes were installed in vertical arrangement in order to increase earth pipe cooling performance. To measure the performance of the system, a numerical model was developed and simulated using the CFD software Fluent in ANSYS 15.0. Data were collected from two modeled rooms built from two shipping containers and installed at the Sustainable Precinct at Central Queensland University, Rockhampton, Australia. The impact of air temperature and velocity on room cooling performance has also been assessed. A temperature reduction of 1.82 °C was observed in the room connected to the vertical earth pipe cooling system, which will save the energy cost for thermal cooling in buildings.