Effects of pH on the stress-strain properties of wool fabric

In wool dyeing and finishing processes, fabric is often treated under conditions of different pHs and is subjected to a variety of physical and chemical environments. This work investigates fabric tensile properties at three different fabric pHs. Wool fabric extensibility under a 5 N/cm load was observed to be greatest at the wool isoelectric point of pH 4.8 and lower at both pH 2.1 and pH 7.2. The impact of pH on fabric extensibility was found to be similar to the variation in fabric hygral expansion previously observed. Fabric stress–strain curves at different pHs showed that for a given fabric extension level, the work required to stretch a fabric was less at pH 2.1 than at pH 4.8. These results suggest that the strength of wool fabric is at maximum when the pH of the fibres is close to the wool isoelectric point and that for consistency, the pH of fabric should be adjusted before standard strength tests are carried out.

The effect of low cycle fatigue, ratcheting and mean stress relaxation on stress-strain response and microstructural development in a dual phase steel

This study examines the cyclic plastic deformation behavior and microstructural development of a dual phase steel in both symmetric and asymmetric cycling in strain and stress control modes. The low-cycle fatigue (LCF) and mean stress relaxation (MSR) tests show very similar fatigue lifetimes. However, fatigue lifetimes reduce and prominent accumulation of directional strain was observed in ratcheting. A microstructural analysis has revealed that the type of cyclic test carried out has a noticeable impact on the substructural development, and this has been correlated with differences in accumulated tensile strain. Electron backscatter diffraction investigation has shown larger in-grain misorientation for ratcheting specimen in comparison with LCF and MSR specimens. The orientation of ferrite grains was found to have very little effect on their substructural development, and strain localization commonly occurred in the ferrite at the ferrite/martensite interface.

Prediction of stress-strain behaviors in steels using an integrated constitutive, FEM and ANN model

Austenitic steels with a carbon content of 0.0037 to 0.79 wt% C are torsion tested and modeled using a physically based constitutive model and an Integrated Phenomenological and Artificial neural Network (IPANN) model. The prediction of both the constitutive and IPANN models on steel 0.017 wt% C is then evaluated using a finite element (FEM) code ABAQUS with different reduction in the thickness after rolling through one roll stand. It is found that during the rolling process, the prediction accuracy of the reaction force from FEM simulation for both constitutive and IPANN models depends on the strain achieved (average reduction in thickness). By integrating FEM into IPANN model and introducing the product of strain and stress as an input of the ANN model, the accuracy of this integrated FEM and IPANN model is higher than either the constitutive or IPANN model.

Analytic prediction of structural stress-strain relations of microstructured metal

Nanostructured and ultra-fine grained metals have higher strength but extremely limited ductility compared to coarse grained metals. However, their ductility can be greatly improved by introducing a specific range of grain sizes in the microstructures. In the paper, multiscale unit cell approach (UCA) is developed and applied to predict the averaged stress-strain relations of the multiscale microstructure metals. The unit cell models are three-phase structured at different scale lengths of 100 nm, 1 μm and 10 μm with different volume fractions and periodic boundary conditions. The contributions of multi-scale microstructures to the macroscopic structural properties of metals are also studied using a analytic approach—two-step mean-field method (TSMF), where three microstructural parameters are introduced and thus mechanical properties such as strength and ductility are presented as a function of these parameters. For verification of these proposed numerical and theoretical algorithms, the structural properties of the pure nickel with three-grain microstructures are studied and the results from FEA and the proposed theory have good agreement.

Uniform elongation and the stress-strain flow curve of steels calculated from hardness using empirical correlations

An empirical relationship between the hardness and uniform elongation of non-Austenitic hypoeutectoid steels has been developed. This new hardness-elongation relationship was combined with previously developed correlations of hardness and strength (yield and ultimate tensile strength) to predict the stressstrain flow curve from a single hardness test. The current study considers both power law hardening behavior and exponential hardening behavior. Reasonable agreement was observed between the experimental and predicted flow curves of a high strength, low alloy steel. Additionally, an empirical correlation of the flow strength at instability with hardness is provided. © ASM International.

Data gathered during investigations into the evolution of hot working stress and microstructure in Mg-3Al-1Zn

The data is the result of hot deformation tests conducted on magnesium alloy AZ31. It includes stress strain data for a range of deformation conditions and different initial microstructures. It also includes data for the developed grain size and the degree of dynamic recrystallisation.

Dynamic strain-induced ferrite transformation during hot compression of low carbon Si-Mn steels

The dynamic strain-induced transformation (DSIT) of austenite to ferrite was investigated under different undercooling conditions using three low carbon Si-Mn steels. The undercooling of austenite (ΔT) was controlled by varying the cooling rate between austenitization and deformation temperatures. Uniform DSIT ferrite grains (∼2.3 μm) were produced at a relatively high deformation temperature above 840°C using a low carbon high Si steel (0.077C-0.97Mn-1.35Si, mass%) in connection with a larger ΔT. The critical conditions for DSIT were determined based on the flow stress-strain curves measured during hot compression tests. Influence of deformation temperature on DSIT of low carbon Si-added steel was also discussed.

Multiscale modelling of stress and strain partitioning in high strength dual phase steels

Multiscale modelling of stress and strain partitioning in DP steel was carried out using both realistic microstructure-based RVE models as well as stochastic microstructures generated by Monte Carlo method. The stochastic microstructure models were shown to resemble that of realistic microstructures, enabling research on the specific aspects of the microstructure that could be difficult to control and study during experimental work. One such feature of the realistic microstructures studied in this work was the grain size and microstructure morphology. The microstructures were generated with varying average grain sizes while all other parameters, such as boundary conditions, material properties and volume fractions of martensite and ferrite were kept constant. It is found that the effect of grain size is much more pronounced during the initial localisation of the plastic deformation at and around the interface of the phases. In addition, the decrease in ductility and increase in strength of the DP steels are directly related to the refinement of grain sizes of each phase and the stress-strain partitioning in between them.

On the Bauschinger effect in dual phase steel at high levels of strain

The effect of volume fraction and hardness of martensite on the Bauschinger effect in Dual Phase (DP) steel was investigated for strain levels close to those observed in automotive stamping. Five different grades of DP steel were produced by controlled heat treatment allowing the examination of the Bauschinger effect for three different volume fractions of martensite and three levels of martensite hardness. Compression-tension and shear reversal tests were performed to examine the Bauschinger effect at high levels of forming strain. Good correlation between the shear reversal and the compression-tension test was observed suggesting that for DP steel, shear stress strain data, converted to equivalent stress-strain, may be applied directly to characterize kinematic hardening behavior for numerical simulations. Permanent softening was observed following strain reversal and increased with martensite volume fraction and pre-strain level. While the Bauschinger ratio saturates at 3% pre-strain, the Bauschinger strain increases linearly with forming strain without showing saturation. This suggests that to model material behavior accurately in forming processes involving complex loading paths and high levels of strain, test data generated at high strain is required.

Influence of porosity on shape memory behavior of porous TiNi shape memory alloy

Porous Ti-50.5at.%Ni shape memory alloy (SMA) samples with a range of  porosities were prepared by spacer sintering. The porous structure of the alloy was examined using scanning electron microscopy (SEM). The phase constituents of the porous TiNi alloy were determined by X-ray diffraction (XRD). The shape memory behavior of the porous TiNi alloy was investigated using loading–unloading compression tests. Results indicate that the porous TiNi alloy exhibits superelasticity and the recoverable strain by the superelasticity decreases with the increase of porosity. After a prestrain of 7%, the superelastically recovered strains for the porous TiNi alloy samples with porosities of 46%, 59%, 69% and 77% are 2.0%, 1.8%, 1.5% and 1.3%, respectively. The pores in the TiNi alloy samples cause stress/strain concentration, as well as crack initiation, which adversely affect the shape memory behavior of the porous TiNi alloy.

Predicting the resistance of fired clay bricks to salt attack

The salt attack of Fired Clay Bricks (FCBs) causes surface damage that is aesthetically displeasing and eventually leads to structural damage. Methods for determining the resistances of FCBs to salt weathering have mainly tried to simulate the process by using accelerating aging tests. Most research in this area has concentrated on the types of salt that can cause damage and the damage that occurs during accelerated aging tests. This approach has lead to the use of accelerated aging tests as standard methods for determining resistance. Recently, it has been acknowledged that are not the most reliable way to determine salt attack resistance for all FCBs in all environments. Few researchers have examined FCBs with the aim of determining which material and mechanical properties make a FCB resistant to salt attack. The aim of this study was to identify the properties that were significant to the resistance of FCBs to salt attack. In doing so, this study aids in the development of a better test method to assess the resistance of FCBs to salt attack. The current Australian Standard accelerated aging test was used to measure the resistance of eight FCBs to salt attack using sodium sulfate and sodium chloride. The results of these tests were compared to the water absorption properties and the total porosity of FCBs. An empirical relationship was developed between the twenty-four-hour water absorption value and the number of cycles to failure from sodium sulfate tests. The volume of sodium chloride solution was found to be proportional to the total porosity of FCBs in this study. A phenomenological discussion of results led to a new mechanism being presented to explain the derivation of stress during salt crystallisation of anhydrous and hydratable salts. The mechanical properties of FCBs were measured using compression tests. FCBs were analysed as cellular materials to find that the elastic modules of FCBs was equivalent for extruded FCBs that had been fired a similar temperatures and time. Two samples were found to have significantly different elastic moduli of the solid microstructure. One of these samples was a pressed brick that was stiffer due to the extra bond that is obtained during sintering a closely packed structure. The other sample was an extruded brick that had more firing temperature and time compared with the other samples in this study. A non-destructive method was used to measure the indentation hardness and indentation stress-strain properties of FCBs. The indentation hardness of FCBs was found to be proportional to the uniaxial compression strength. In addition, the indentation hardness had a better linear correlation to the total porosity of FCBs except for those samples that had different elastic moduli of the solid microstructure. Fractography of exfoliated particles during salt cycle tests and compression tests showed there was a similar pattern of fracture during each failure. The results indicate there were inherent properties of a FCB that determines the size and shape of fractured particles during salt attack. The microstructural variables that determined the fracture properties of FCBs were shown to be important variables to include in future models that attempt to estimate the resistance of FCBs to salt attack.

Simulation of Mg sheet press cell materials

Major characteristics of Magnesium alloy are low density (= 1.8 g/cm³) and excellent recyclability; therefore Mg is considered as one of low environmental loading materials. The low-density materials, such as Mg, are suitable for the transportation system to reduce the emission of Co2, save energy resource and increase the safety for accidents like corrosions. In the place, cellular materials like aluminum foams are also low-density materials and can be controlled the stress-strain relation. Combination of Mg alloy and cellular materials, that is Mg cell, is one of the most excellent materials for transportation system, because of its ultra low density. safeties, and recycle ability. To make the Mg cellular materials. there are some problems to solve. One is how to make them uniformly to supply them as same perfonnance materials. One is how to make them inexpensively. Most of cellular materials are very expensive because of there are many processes or special fabrication system to make them. To solve these problems. we investigated the press cell materials. The press cell material consists sheets pressed as cell shape and wall. Therefore, it is very easy to make cellular materials and control validation of the performance of each foam materials. In this paper, we simulated compression tests of this new type of Mg alloy cellular materials under dynamic loading to investigate the relation between the compression speed and the compression behavior to show the shock absorbing capability of this new foam material. It is very important to understand their mechanical properties relatcd with cell shapes and wall to be applied widely.

Strain differences in coping behaviour, novelty seeking behaviour, and susceptibility to socially conditioned fear : a comparison between Wistar and Sprague Dawley rats

The aim of the current study was to generate socially conditioned fear in two different strains of rat (Wistar, W and Sprague Dawley, SD) using social conflict, in order to investigate whether the magnitude of the conditioned fear responses in each strain was related to behaviour exhibited prior to or during fear induction (i.e. social conflict). On day one of the study, all intruders were assessed for exploratory activity in a novel environment. Twenty four hours following the novel environment test the locomotor activity of the intruders was assessed, while they underwent a single familiarisation exposure to the arena in which the conflict was subsequently to occur in. Twenty-four hours following familiarisation, intruders underwent either a 10 min social conflict or sham conflict session. One day later we examined the response of the intruders when they were returned to the vacant resident's cage. Upon return to the conflict context, we examined the intruder's ultrasonic distress vocalisations and the extent to which locomotor activity was inhibited. We found that W rats displayed significantly more immobility (i.e. conditioned fear) upon return to context than did SD rats (p < 0.05). Importantly, we observed that the differences in the two strains behaviour upon return to context appeared to be related to their quite different patterns of coping behaviour. The results of the current study indicate that preclinical between-strain comparisons potentially have much to offer in regard to understanding the basis of resilience to social stress.

Influence of grain size and training temperature on strain of polycrystalline Ni50Mn29Ga21 samples

The alloy Ni-Mn-Ga aroused great interest for application as a magnetic shape memory (MSM) material. This effect is caused by reorientation of twin variants by an external magnetic field. So far, most of the experiments were concentrated on single crystals. But, the MSM effect can also be realised in polycrystals which can be prepared much more efficiently. Here, polycrystalline samples were prepared by directional solidification with a <100> fibre texture of the high temperature cubic austenitic phase parallel to the heat flow. Afterwards, a heat treatment was applied for chemical homogenisation and stress relaxation in the austenitic state. Then the samples were heated up to the austenitic state and cooled down under load. The microstructure was analysed by Electron Back Scatter Diffraction (EBSD) before and after that treatment. Mechanical training at room temperature and 40°C was tracked by recording stress-strain curves. By increasing the number of training cycles the strain also increases. The influence of different training temperatures was investigated on samples with different grain sizes.

A uniaxial tensile stage with tracking capabilities for micro X-ray diffraction applications

First results are presented for a uniaxial tensile stage designed to operate on a scanning micro X-ray diffraction synchrotron beamline. The new tensile stage allows experiments at typical loading cycles used in standard engineering stress–strain tests. Several key features have been implemented to support in situ loading experiments at the intragranular length scale. The physical size and weight of the load cell were minimized to maintain the correct working distance for the X-ray focusing optics and to avoid overloading the high-resolution raster scan translation stages. A high-magnification optical microscope and image correlation code were implemented to enable automated online tracking capabilities during macroscopic elongation of the sample. Preliminary in situ tensile loading experiments conducted on beamline 12.3.2 at the Advanced Light Source using a polycrystalline commercial-purity Ti test piece showed that the elastic–plastic response of individual grains could be measured with submicrometre spatial resolution. The experiments highlight the unique instrumentation capabilities of the tensile stage for direct measurement of deviatoric strain and observation of dislocation patterning on an intragranular length scale as a function of applied load.