Seasonal storage for solar thermal systems in Australia?

Seasonal storage systems have been operating in various European countries since 1985. Combined with solar collectors, these systems are known as ‘central solar heating plants with seasonal storage’ (CSHPSS). While these systems have been shown to be technically feasible, their cost is still too high to make them competitive with fossil fuels.

In Australia, we have quite different conditions to those countries where CSHPSS have been trialled. In general, we experience higher radiation levels, ambient temperatures and cooling loads. Our heating loads and energy prices are also usually lower. As a result, any evaluation of CSPSS operating in a European context may not be valid for Australian conditions. To the authors’ knowledge, no evaluation of these systems has been carried out for Australia.

This paper therefore attempts an initial assessment of these systems and their viability for Australia. The paper first describes the various types of CSHPSS and then reviews their current status. The performance of one type of CSHPSS operating in several locations of Australia has been predicted using a TRNSYS model. The simulations indicated that the design guidelines for Europe are inappropriate for Australia and would result in greatly over-sized systems.

An indication of the financial viability of the system was determined by calculating a simple payback period for a variety of fossil fuels. This type of seasonal storage systems appears to be financially attractive in areas of southern Australia where the solar system is displacing LPG.

The contribution of residential solar energy systems to the reduction of greenhouse gas emissions in the borough of Queenscliffe

The Borough of Queenscliffe has identified the importance of reducing its greenhouse gas emissions and aims to become a carbon zero municipality by 2020. For a house, suburb or town to become carbon neutral ideally it produces an equivalent amount of energy from renewable resources to that which it consumes. By increasing the number of solar systems, both photovoltaic (PV) and hot water, in the residential sector, greenhouse gas emissions will be reduced. The number of solar systems located in the Borough of Queenscliffe has been estimated and a database of these systems has been created, including the size and panel orientation. The energy generated by each solar system, in addition to the reductions in greenhouse gas emissions, has been calculated for an average year.

Analytical modeling of partially shaded photovoltaic systems

As of today, the considerable influence of select environmental variables, especially irradiance intensity, must still be accounted for whenever discussing the performance of a solar system. Therefore, an extensive, dependable modeling method is required in investigating the most suitable Maximum Power Point Tracking (MPPT) method under different conditions. Following these requirements, MATLAB-programmed modeling and simulation of photovoltaic systems is presented here, by focusing on the effects of partial shading on the output of the photovoltaic (PV) systems. End results prove the reliability of the proposed model in replicating the aforementioned output characteristics in the prescribed setting. The proposed model is chosen because it can, conveniently, simulate the behavior of different ranges of PV systems from a single PV module through the multidimensional PV structure.

The telescopic eye: aqua optica

The Telescopic Eye: Aqua Optica was an installation work which explores concepts and philosophies related to instrumental, lens based observations of heavens as experienced when seeing through a telescope. In particular it considers how the eye of the observer and the lens of the telescope must act in unison to extend both the perception and conception of that which is remote and beyond direct naked eye sensing - an act of transcendence. A series of projected images (the video) of celestial objects are observed by the viewer through a large spherical aquatic lens which is mounted on a large wooden tripod. These images slowly dissolve and morph into each other. The sequence in which these images are presented is based on approximate chronological order in which these celestial objects were historically observed through the telescope – such as the local bodies of our the solar system starting with the Moon, Jupiter and Saturn (as first observed by Galileo in 1610) and eventually extending out to distant nebula, star clusters and galaxies. For the Transduction exhibition the Telescopic Eye: Aqua Optica was installed outside in a small quadrangle next to the Tech Bar and as the night drew darker it was able to also embody the lighting and other visual elements from the surrounding buildings and streets. The Aqua Optica system often encompasses such local lighting and images as a added layer to the video projection work. In this case (at night and outside at Federation Square) the extent of the layering was very successful and increased dramatically as the night became darker. This multi layering of images invokes (for the viewer) a connection between the immediate environment of the Federation square and cityscape with the vastly distant images of the cosmos. For me such a multilayered imaging represents how scientific instruments of observation can generate a complex and augmented visualisation of reality, one which has historically come to re-define our conception of the cosmos and our place in it both spatially and temporally.

A medium-temperature solar thermal power system and its efficiency optimisation

This paper firstly expounds that the reheat-regenerative Rankine power cycle is a suitable cycle for the parabolic trough collector, a popular kind of collector in the power industry. In a thermal power cycle, the higher the temperature at which heat is supplied, the higher the efficiency of the cycle. On the other hand, for a given kind of collector at the same exiting temperature, the higher the temperature of the fluid entering the collector, the lower the efficiency of the collector. With the same exiting temperature of the solar field and the same temperature differences at the hottest end of the superheater/reheater and at the pinch points in the heat exchangers (e.g., the boiler) in the cycle, the efficiencies of the system are subject to the temperature of the fluid entering the collector or the saturation temperature at the boiler. This paper also investigates the optimal thermal and exergetic efficiencies for the combined system of the power cycle and collector. To make most advantage of the collector, the exiting fluid is supposed to be at the maximum temperature the collector can harvest. Hence, the thermal and exergetic efficiencies of the system are related to the saturation temperature at the boiler here.

Development of a building integrated photovoltaic/thermal solar energy cogeneration system

Using renewable energy sources for onsite cogeneration from structural building elements is a relatively new concept and is gaining considerable interest. In this study the design, development, manufacturing and testing of a novel building integrated photovoltaic/thermal (BIPVT) solar energy cogeneration system is discussed.

Adhesives (ADH), resistance seam welding (RSW) and autoclaving (ATC) were identified as the most appropriate for fabricating BIPVT roofing panels. Of these manufacturing methods ADH was found to be most suitable for low volume production systems due to its low capital cost.

A prototype panel, fabricated using ADH methods, exhibited good thermal performance. It was also shown that BIPVT performance could be theoretically predicted using a one dimensional heat transfer model and showed excellent agreement with experimental data. The model was used to suggest further design improvements. Finally, a transient simulation of the BIPVT was performed in TRNSYS and is used to illustrate the benefits of the system.

Designing a low cost solar collector system for process industry applications

New Zealand is a large producer and processor of primary products and has a climate with high levels of solar radiation. However, the use of solar energy for heating and cooling in the processing industries has received limited attention.
For this study, the design of a low cost solar collector is analysed and discussed. Furthermore, the methods for integrating the collector into water heating and cooling systems in a hypothetical processing environment are examined. An F-Chart analysis is used to simulate the performance of large-area arrays of the solar collector and to determine its potential contribution to heating and cooling loads.
The study shows that for a storage-based system, the contribution of solar energy is determined mainly by the collector area to storage volume ratio. It is suggested that this low cost collector could make a significant contribution to energy use in processing plants and may be an attractive future technology.

Solar photocatalytic oxidation system for colour removal in dyeing effluent

The effectiveness of various photocatalysts including titanium dioxide and other oxidants was investigated in a solar powered UV photocatalytic oxidation system for colour removal in dyeing effluent. A semi-empirical constant model and guidelines were developed to assist the design and to evaluate the full scale of the system.

A simple-to-use calculator for determining the total solar heat gain of a glazing system

Architects and designers could readily use a quick and easy tool to determine the solar heat gains of their selected glazing systems for particular orientations, tilts and climate data. Speedy results under variable solar angles and degree of irradiance would be welcomed by most. Furthermore, a newly proposed program should utilise the outputs of existing glazing tools and their standard information, such as the use of U-values and Solar Heat Gain Coefficients (SHGC’s) as generated for numerous glazing configurations by the well-known program WINDOW 6.0 (LBNL, 2001). The results of this tool provide interior glass surface temperature and transmitted solar radiation which link into comfort analysis inputs required by the ASHRAE Thermal Comfort Tool –V2 (ASHRAE, 2011). This tool is a simple-to-use calculator providing the total solar heat gain of a glazing system exposed to various angles of solar incidence. Given basic climate (solar) data, as well as the orientation of the glazing under consideration the solar heat gain can be calculated. The calculation incorporates the Solar Heat Gain Coefficient function produced for the glazing system under various angles of solar incidence WINDOW 6.0 (LBNL, 2001). The significance of this work rests in providing an orientation-based heat transfer calculator through an easy-to-use tool (using Microsoft EXCEL) for user inputs of climate and Solar Heat Gain Coefficient (WINDOW-6) data. We address the factors to be considered such as solar position and the incident angles to the horizontal and the window surface, and the fact that the solar heat gain coefficient is a function of the angle of incidence. We also discuss the effect of the diffuse components of radiation from the sky and those from ground surface reflection, which require refinement of the calculation methods. The calculator is implemented in an Excel workbook allowing the user to input a dataset and immediately produce the resulting solar gain. We compare this calculated total solar heat gain with measurements from a test facility described elsewhere in this conference (Luther et.al., 2012).

Modelling and power quality analysis of a grid-connected solar PV system

Increased concern about global warming coupled with the escalating demand of energy has driven the conventional power system to be more reliable one by integrating Renewable Energies (RE) in to grid. Over the recent years, integration of solar PV forming a gridconnected PV is considered as one of the most promisingtechnologies to the developed countries like Australia to meet the growing demand of energy. This rapid increase in grid connected photovoltaic (PV) systems has made the supply utilities concerned about the drastic effects that have to be considered on the distribution network in particular voltage fluctuations, harmonic distortions and the Power factor for sustainable power generation. However, irrespective of thefact that the utility grid can accommodate the variability of load or irregular solar irradiance, it is essential to study the impact of grid connected PV systems during higher penetration levels as the intermittent nature of solar PV adversely effects the grid characteristics in meeting the load demand. Hence, keeping this in track, this paper examines the grid-connected PV system considering a residential network of Geelong region (38◦.09' S and 144◦.21’ E) and explores the level of impacts considering summer load profile with a change in the level of integrations. Initially, a PV power system network model is developed in Matlab-Simulink environment and the simulations are carried out to explore the impacts of solar PV penetration at low voltage distribution network considering power quality (PQ) issues such as voltage fluctuations, harmonics distortion at different load conditions.

Impact analysis study in a typical solar PV microgrid power system

Microgrid (MG) power system with Distributed Generation (DG) plays an important role to provide reliable, secure, and low carbon emission energy supply for communities, in case of any failure or disturbance of energy supply from the main grid. At the same time, DG also contributes to several technical issues in the MG distribution network. Power quality (PQ) issues are one of the main technical challenges when integrating Renewable Energy (RE) sources in MG network. In this paper, the PQ issues like; power variation, voltage deviation, and Total Harmonic Distortion (THD) have been addressed by an impact analysis study on a typical solar PV MG power system in both on-grid and off-grid mode of operation. Analysis results from the study will be helpful in developing an independent MG power system with improved PQ conditions.