Solar energy use for energy savings in dairy processing plants

New Zealand is one of the world’s largest producers of dairy products and has a climate with high levels of solar radiation; however, the use of solar energy in the dairy processing industry has received limited attention. An examination of historical records found that the annual peak in New Zealand milk production and processing occurs at a time when solar radiation levels are increasing markedly. An F-Chart analysis was used to simulate the performance of large-area arrays of solar collectors and to determine their suitability for heating and cooling in a dairy processing environment. For the study four types of solar collectors were analysed: glazed flat plates, evacuated tubes, evacuated tubes with CPC reflectors and a building-integrated solar collector under development at the University of Waikato (UoW). It was found that of these echnologies, both flat plate and evacuated tubes with CPC reflectors could make useful heating and cooling contributions. Furthermore, the solar fraction was determined mainly by the collector area to storage volume ratio. Finally, it was found that the UoW building-integrated solar collector could make a significant contribution to energy use in dairies and may be an attractive future technology for the industry.

Development of a building integrated photovoltaic/thermal solar energy cogeneration system

Using renewable energy sources for onsite cogeneration from structural building elements is a relatively new concept and is gaining considerable interest. In this study the design, development, manufacturing and testing of a novel building integrated photovoltaic/thermal (BIPVT) solar energy cogeneration system is discussed.

Adhesives (ADH), resistance seam welding (RSW) and autoclaving (ATC) were identified as the most appropriate for fabricating BIPVT roofing panels. Of these manufacturing methods ADH was found to be most suitable for low volume production systems due to its low capital cost.

A prototype panel, fabricated using ADH methods, exhibited good thermal performance. It was also shown that BIPVT performance could be theoretically predicted using a one dimensional heat transfer model and showed excellent agreement with experimental data. The model was used to suggest further design improvements. Finally, a transient simulation of the BIPVT was performed in TRNSYS and is used to illustrate the benefits of the system.

Utilising solar energy within conventional coal fired power stations

Although the thermodynamic advantages of using solar energy to replace the bled off steam in the regeneration system of Rankine cycle coal fired power stations has been proven theoretically, the practical techno/economic feasibility of the concept has yet to be confirmed relative to real power station applications. To investigate this concept further, computer modelling software “THERMSOLV” was specifically developed for this project at Deakin University, together with the support of the Victorian power industry and Australian Research Council (ARC). This newly developed software simulates the steam cycle to assess the techno/economic merit of the solar aided concept for various power station structures, locations and local electricity market conditions. Two case studies, one in Victoria Australia and one in Yunnan Province, China, have been carried out with the software. Chapter one of this thesis defines the aims and scope of this study. Chapter two details the literature search in the related areas for this study. The thermodynamic concept of solar aid power generation technology has been described in chapter three. In addition, thermodynamic analysis i.e. exergy/availability has been described in this chapter. The “Thermosolv” software developed in this study is detailed in chapter four with its structure, functions and operation manual included. In chapter five the outcomes of two case studies using the “Thermosolv” software are presented, with discussions and conclusions about the study in chapters 6 and 7 respectfully. The relevant recommendations are then made in chapter eight.

The contribution of residential solar energy systems to the reduction of greenhouse gas emissions in the borough of Queenscliffe

The Borough of Queenscliffe has identified the importance of reducing its greenhouse gas emissions and aims to become a carbon zero municipality by 2020. For a house, suburb or town to become carbon neutral ideally it produces an equivalent amount of energy from renewable resources to that which it consumes. By increasing the number of solar systems, both photovoltaic (PV) and hot water, in the residential sector, greenhouse gas emissions will be reduced. The number of solar systems located in the Borough of Queenscliffe has been estimated and a database of these systems has been created, including the size and panel orientation. The energy generated by each solar system, in addition to the reductions in greenhouse gas emissions, has been calculated for an average year.

A pixel-based approach to estimation of solar energy potential on building roofs

Precise estimation of solar energy on building roofs plays a critical role in sustainable development and renewable energy consumption of high-density human habitats. Conventional solar radiation models based on costly Light Detection and Ranging (LiDAR) data are only adequate for existing buildings, not for future construction areas. In this paper, a pixel-based methodology is constructed for estimating solar energy potential over roofs. Buildings with flat roofs in a newly planned construction area are chosen as a case study. The solar radiation at a certain cell is mathematically formulated in the pixel unit, and its yields over a certain time period are calculated by considering multiple instantaneous solar irradiances and are visually presented by image processing. Significant spatial and temporal variations in solar radiation are measured. Within the study area, the maximum and minimum annual radiation yields are estimated at 4717.72 MJ/m2/year and 342.58 MJ/m2/year respectively. Radiation contour lines are then mapped for outlining installation ranges of various solar devices. For each apartment building, around 20% of roof areas can obtain 4500 MJ/m2/year or more solar radiation yields. This study will benefit energy investors and urban planners in accurately predicting solar radiation potential and identifying regions with high radiation over building roofs. The results can be utilised in government policies and urban planning to raise awareness of the use of renewable energy sources.

Net energy analysis of solar and conventional domestic hot water systems in Melbourne, Australia

It is commonly assumed that solar hot water systems save energy and reduce greenhouse gas emissions. Very rarely has the life-cycle energy requirements of solar hot water systems been analysed, including their embodied energy. The extent to which solar hot water systems save energy compared to conventional systems in Melbourne, Australia, is shown through a comparative net energy analysis. The solar systems provided a net energy saving compared to the conventional systems after 0.5 to 2 years, for electricity and gas systems respectively.

The core of the global warming problem: energy

From the thermodynamic point of view, the global warming problem is an ''energy balance'' problem. The heat (energy) accumulation in the earth and its atmosphere is the cause of the global warming. This accumulation is mainly due to the imbalance of (solar) energy reaching and the energy leaving the earth, caused by ''greenhouse effect'' in which the CO₂ and other greenhouse gases play a critical role; so that balance of the energy entering and leaving the earth should be the key to solve the problem. Currently in the battle of tackling the global warming, we mainly focus on the development of CO₂-related measures, i.e., emission reduction, CO₂ sequestration, and CO₂ recycle technologies. It is right in technical aspect, because they are attempting thinner the CO₂ ''blanket'' around the earth. However, ''Energy'' that is the core of the problem has been overlooked, at least in management/policy aspect. This paper is proposing an ''Energy Credit'' i.e., the energy measure concept as an alternative to the ''CO₂ credit'' that is currently in place in the proposed emission trading scheme. The proposed energy credit concept has the advantages such as covering broad activities related to the global warming and not just direct emissions. Three examples are given in the paper to demonstrate the concept of the energy measure and its advantages over the CO₂ credit concept.

Solar aided power generation from coal fired power stations: THERMSOLV software

Although the thermodynamic advantages of using solar energy to replace the bleed off steam in the regeneration system of Rankine cycle coal fired power stations has been proven theoretically, the practical techno/economic feasibility of the concept has yet to be confirmed relative to real power station applications. To investigate this concept further, a computer modelling software “THERMSOLV” was developed by Deakin University researchers, together with the support of the Victorian power industry and Australian Research Council (ARC). This newly developed software simulates the steam cycle to assess the techno/economic merit of the solar aided concept for various power station structures, locations and local electricity market conditions. Two case studies, one in Victoria Australia and one in Yunnan Province, China, have been carried out to show the application of the software. This paper reports the structure and functions of the software, and the results of the two case studies.

High performance low-energy buildings

The era of legislation and creditable methods towards producing sustainable buildings is upon us. Yet, a major barrier to achieving environmental responsive design is in the lack of available information at the programming or pre-design phases of a project. The review and evaluation of climate as well as energy-efficient strategies could be difficult to consider at these preliminary stages. Until recently, introducing energy simulation tools at the design stage has been difficult and perhaps next to impossible at a pre-design or programming stage. However, analysis of this sort is essential to ‘green building rating’ or performance assessment schemes such as LEED (Leadership in Energy and Environmental Design) and BREEAM (Building Research Establishment Environment Assessment Method). This paper discusses the implementation of a particular tool, ENERGY-10, where ‘basecase’ building defaults are compared to a low-energy case which has applied multiple energy-efficient strategies automatically. An annual hour-by-hour simulation provides a daylighting calculation with a subsequent thermal evaluation. Calculation results provide energy consumption, peak load equipment sizing, a RANK feature of the energy-efficient strategies, reporting of CO2, SO2 and NOx reduction, optimum glazing type as well as excellent graphic output. Consideration is given as to the approach of how such information can be introduced into the building project brief enforcing a low-energy<br />performance target.

Solar adsorption refrigeration : an alternative/auxiliary way for thermal storage for air conditioning

This paper presents an idea of using solar powered adsorption ice making system as an alternative or an auxiliary way for the traditional ice storage air conditioning systems. A simple solar adsorption refrigeration system runs in intermittent cycle. It makes cooling effect at night, and the cooling effect can be stored for the day use. It fits in well with the cycle of the existing off-peak ice storage air conditioning system. On the top of green effect of the solar powered ice making system, the idea is specifically beneficial for places where the price of the off-peak electricity is not significantly lower than peak price. Based on our many years experience on the solar ice making systems, the paper discusses the technical feature of the solar ice making technology and the solutions we are working on to attack the problems which may have potential damage to application of the solar ice making system for air conditioning purposes.

A solar collector with the absorber divided by rectangular slots

A new solar absorber structure has been proposed and studied in this paper. The metal tubes running perpendicular to a set of parallel rectangular metal fins make the solar absorber with rectangular slots. Studies on the collector were theoretically carried out in the aspects of heat transfer, thermodynamics and . hydrodynamics. The calculating methods for calculating fin efficiency F and efficiency factors of the collector F' were obtained. The results showed that the new solar collector would have the higher efficiency and better performance at higher fluid temperature than that of the traditional flat-plate collectors. A collector prototype with the new structure was built and tested. The testing results agree with our theoretical results.

Solar photocatalytic oxidation (PCO) process with a flat-plate reactor

An experimental rig with a flat-plate solar reactor was built to study the effectiveness of degradation using the reactive methylene blue as sensitive objective. The factors that affect the degradation performance, such as dosages of photocatalyst (Ti0₂), initial concentration of reactive methylene blue, flow rate through the flat-plate reactor, solar UV radiation intensity and decolourising efficiency of the solution, have been investigated. The results showed that the solar PCO process with a Flat-plate Reactor could degrade the methylene blue and decolour in methylene blue solution efficiently.

The influence of housing size, style and location on energy and greenhouse gas emissions

Concern about the growth of greenhouse gas emissions in Victoria has prompted the introduction of legislation to improve the thermal performance of the residential building envelope. Unfortunately, the size of the house is not considered in the rating tool that underpins the legislation. The energy embodied in the constructional materials is also not considered although it too is directly related to the size of the house. Another intrinsic factor relating residential housing energy and greenhouse gas emissions is the location of the residence and the travel preferences of the homeowner. The relationship between the operational, embodied and travel energy associated with a typical residential scenario in Melbourne over the last 50 years is examined in this paper. The analysis found that by the year 2000, the energy associated with work-related travel (44%) now exceeds the operational energy (37%). In terms of greenhouse gas emissions, the contribution from travel energy is almost double that from operational energy (28%).