Small-signal stability assessment of active distribution networks with dynamic loads

This paper investigates small-signal stability of a distribution system with distributed generator and induction motor load, as a dynamic element. The analysis is carried out over a distribution test system with different types of induction motor loads. The system is linearised by the perturbation method. Eigenvalues and participation factors are calculated to see the modal interaction of the system. The study indicates that load voltage dynamics significantly influence the damping of a newly identified voltage mode. This mode has frequency of oscillation between the electromechanical and subsynchronous oscillation of power systems. To justify the validity of the modal analysis time domain simulation is also carried out. Finally, significant parameters of the system that affect the damping and frequency of the oscillation are identified.

An alternative LQR-based excitation controller design for power systems to enhance small-signal stability

This paper presents a new approach to design excitation controller for power systems to enhance small-signal stability. Partial feedback linearization scheme is used to design the controller for a linearized power system model which transforms a part of this model into a new system through linear coordinate transformation. In this paper, the excitation control law as a function of state variables is determined from the dynamics of the partly transformed new system provided that the controller stabilizes the remaining dynamics of the system which are not transformed through feedback linearization. The stability of the remaining dynamics is also discussed in this paper. Since the proposed control scheme uses state variables as feedback, it is analogous to a linear quadratic regulator (LQR) based excitation controller. Therefore, the performance of the proposed scheme is evaluated on a single machine infinite bus (SMIB) system and compared to that of an LQR controller.

Impact of high wind penetration on the voltage profile of distribution systems

In this paper, simulation results showing the effect of lower and higher penetration of distributed wind generation on the voltage profile in distribution systems have been presented. The analysis is carried out over two distribution test systems. The detailed mathematical modeling of the system is also presented. It also investigates the small-signal stability of distribution systems using eigenvalue approach. The analyses show that voltage variation problems occur in different nodes of the distribution networks with an increase of penetration level. However, proper selection of dispersion level can improve the voltage profile of the distribution systems

Balanced-budget consumption taxes and aggregate stability in a small open economy

In a small open economy facing a perfect world capital market, this paper shows that if the government follows a balanced-budget fiscal policy based on endogenous consumption tax rates, then the steady state is saddle-path stable and hence beliefs-driven aggregate instability can be ruled out. This result is in contrast to those obtained in some closed economy models, and it suggests that unrestricted world capital mobility can help stabilize the economy under the balanced-budget fiscal policy based on consumption taxation.

Single transferable vote with Borda elimination: proportional representation, moderation, quasi-chaos and stability

Modifying single transferable vote (STV) by removing candidates according to their Borda scores creates a new vote counting system (STV-B) that is not quasi-chaotic, results in proportional representation, and promotes the election of moderate candidates. Dummett, M.A.E. [1997. Principles of Electoral Reform. Oxford University, New York] noted quasi-chaos in STV and proposed the “Quota/Borda system” (QBS) as a solution. STV-B and QBS retain proportional representation from STV, permit some influence on candidate selection to occur between voting blocks thereby promoting moderate results, and are much more stable than STV when subjected to small changes in voter preferences. Under STV-B, and not QBS, a minority that shares some preferences may elect a candidate even if the minority is not a solid coalition.

1-Naphthyl- and mesityltellurium(IV,II) derivatives of small bite chelating organic ligands: effect of steric bulk and intramolecular secondary bonding interaction on molecular geometry and supramolecular association

The synthesis and characterization of unsymmetric diorganotellurium compounds containing a sterically demanding I-naphthyl or
mesitylligand and a small bite chelating organic ligand capable of 1,4-Te···N(O) intramolecular interaction is described. The reaction
of ArTeCl₃ (Ar = I-C_lOH₇, Np; 2,4,6-Me₃C₆H_2' Mes) with (SB)HgCI [SB = the Schiff base, 2-(4,4'-N0₂C₆H₄CH=NC₆H₃-Me)] or a methyl ketone (RCOCH₃) afforded the corresponding dichlorides (SB)ArTeCI₂ (Ar = Np, 1Aa; Mes, 1Ba) or (RCOCH₂)ArTeCl₂ (Ar = Np; R = Ph (2Aa), Me (3Aa), Np (4Aa); Ar = Mes, R = Ph (2Ba)). Reduction of 1Aa and 1Ba by Na₂S₂0₅ readily gave the tellurides (SB)ArTe (Ar = Np (1A), Mes, (1B) but that of dichlorides derived from methylketones was complicated due to partial decomposition to tellurium powder and diarylditelluride (Ar₂Te₂), resulting in poor yields of the corresponding tellurides 2A, 2B and 3A. Oxidation of the isolated tellurides with S0₂Cl₂, Br₂ and I₂ yielded the corresponding dihalides. All the synthesized compounds have been characterized with the help of IR, ¹H, ^l3C, and ¹²⁵Te NMR and in the case of 2Aa, and 2Ba by X-ray crystallography. Appearance of only one ¹²⁵Te signal indicated that the unsymmetric derivatives were stable to disproportionation to symmetric species. Intramolecular 1,4-Te· . ·0 secondary bonding interactions (SBIs) are exhibited in the crystal structures of both the tellurium(IV) dichlorides, 2Aa, and 2Ba. Steric repulsion of the mesityl group in the latter dominates over lone pair-bond pair repulsion, resulting in significant widening of the equatorial C-Te-C angle. This appears to be responsible for the lack of Te· . ·CI involved supramolecular associations in the crystal structure of 2Ba.

Transparent uv-shielding films from organic small molecule-intercalated layered double hydroxide nanoplatelets/polymer composite

In this study, layered double hydroxide (LDH) with nitrate as the interlayer anion has been partially exfoliated in dimethyl sulfoxide (DMSO). Atomic force microscopy (AFM) images showed that both the lateral size and the thickness of the LDH nanoplatelets were decreased after DMSO treatment. Formation of transparent LDH suspension in DMSO was observed. Taking this advantage, we have prepared transparent LDH/ethylene-vinyl alcohol copolymer (EVOH) nanocomposite films using DMSO as the processing solvent. Organic small molecules, UV absorbers, were intercalated into the LDH interlayers to incorporate the UV-shielding property into the transparent composite films. The thermal stability of UV absorbers was considerably improved after intercalation, which was attributed to the electrostatic interaction between the guest UV absorbers and the host LDH layers. The prepared composite films were flexible and exhibited excellent UV-shielding capability, but had transmittance as high as 90% in the visible region. The effect of LDH filler on thermal and mechanical properties of the composite films was also examined.

Ionic liquids and organic ionic plastic crystals utilizing small phosphonium cations

The development of new liquid and solid state electrolytes is paramount for the advancement of electrochemical devices such as lithium batteries and solar cells. Ionic liquids have shown great promise in both these applications. Here we demonstrate the use of phosphonium cations with small alkyl chain substituents, in combination with a range of different anions, to produce a variety of new halide free ionic liquids that are fluid, conductive and with sufficient thermal stability for a range of electrochemical applications. Walden plot analysis of the new phosphonium ionic liquids shows that these can be classed as "good" ionic liquids, with low degrees of ion pairing and/or aggregation, and the lithium deposition and stripping from one of these ionic liquids has been demonstrated. Furthermore, for the first time phosphonium cations have been used to form a range of organic ionic plastic crystals. These materials can show significant ionic conductivity in the solid state and thus are of great interest as potential solid-state electrolyte materials.

Proline residues within spacer peptide p1 are important for human immunodeficiency virus type 1 infectivity, protein processing, and genomic RNA dimer stability

The full-length human immunodeficiency virus type 1 (HIV-1) mRNA encodes two precursor polyproteins, Gag and GagProPol. An infrequent ribosomal frameshifting event allows these proteins to be synthesized from the same mRNA in a predetermined ratio of 20 Gag proteins for each GagProPol. The RNA frameshift signal consists of a slippery sequence and a hairpin stem-loop whose thermodynamic stability has been shown in in vitro translation systems to be critical to frameshifting efficiency. In this study we examined the frameshift region of HIV-1, investigating the effects of altering stem-loop stability in the context of the complete viral genome and assessing the role of the Gag spacer peptide p1 and the GagProPol transframe (TF) protein that are encoded in this region. By creating a series of frameshift region mutants that systematically altered the stability of the frameshift stem-loop and the protein sequences of the p1 spacer peptide and TF protein, we have demonstrated the importance of stem-loop thermodynamic stability in frameshifting efficiency and viral infectivity. Multiple changes to the amino acid sequence of p1 resulted in altered protein processing, reduced genomic RNA dimer stability, and abolished viral infectivity. The role of the two highly conserved proline residues in p1 (position 7 and 13) was also investigated. Replacement of the two proline residues by leucines resulted in mutants with altered protein processing and reduced genomic RNA dimer stability that were also noninfectious. The unique ability of proline to confer conformational constraints on a peptide suggests that the correct folding of p1 may be important for viral function.

The small molecule, genistein, increases hepcidin expression in human hepatocytes

Hepcidin, a peptide hormone that decreases intestinal iron absorption and macrophage iron release, is a potential drug target for patients with iron overload syndromes because its levels are inappropriately low in these individuals. Endogenous stimulants of Hepcidin transcription include bone morphogenic protein 6 (BMP6) and interleukin-6 (IL-6) by effects on mothers against decapentaplegic homolog (Smad)4 or signal transducer and activator of transcription (Stat)3, respectively. We conducted a small-scale chemical screen in zebrafish embryos to identify small molecules that modulate hepcidin expression. We found that treatment with the isoflavone, genistein, from 28-52 hours postfertilization in zebrafish embryos enhanced Hepcidin transcript levels, as assessed by whole-mount in situ hybridization and quantitative real-time reverse-transcriptase polymerase chain reaction. Genistein's stimulatory effect was conserved in human hepatocytes: Genistein treatment of HepG2 cells increased both Hepcidin transcript levels and promoter activity. We found that genistein's effect on Hepcidin expression did not depend on estrogen receptor signaling or increased cellular iron uptake, but was impaired by mutation of either BMP response elements or the Stat3-binding site in the Hepcidin promoter. RNA sequencing of transcripts from genistein-treated hepatocytes indicated that genistein up-regulated 68% of the transcripts that were up-regulated by BMP6; however, genistein raised levels of several transcripts involved in Stat3 signaling that were not up-regulated by BMP6. Chromatin immunoprecipitation and ELISA experiments revealed that genistein enhanced Stat3 binding to the Hepcidin promoter and increased phosphorylation of Stat3 in HepG2 cells. Conclusion: Genistein is the first small-molecule experimental drug that stimulates Hepcidin expression in vivo and in vitro. These experiments demonstrate the feasibility of identifying and characterizing small molecules that increase Hepcidin expression. Genistein and other candidate molecules may subsequently be developed into new therapies for iron overload syndromes.

Improved 2D‐HPLC of red wine by incorporating pre‐process signal‐smoothing algorithms

Twomultidimensional HPLC separations of an Australian red wine are presented, >70% of the available separation space was used. A porous graphitic carbon (PGC) stationary phase was used as the first dimension in both separations with both RP core–shell and hydrophilic interaction chromatography fully porous columns used separately in the second dimension. To overcome peak analysis problems caused by signal noise and low detection limits, the data were pre-processed with penalised least-squares smoothing. The PGC × RP combination separated 85 peaks with a spreading angle of 71 and the PGC × hydrophilic interaction chromatography separated 207 peaks with a spreading angle of 80. Both 2D-HPLC steps were completed in 76 min using a comprehensive stop-and-go approach. A smoothing step was added to peak-picking processes and was able to greatly reduce the number of false peaks present due to noise in the chromatograms. The required thresholds were not able to ignore the noise because of the small magnitude of the peaks; 1874 peaks were located in the non-smoothed PGC × RP separation that reduced to 227 peaks after smoothing was included.

Slope stability analysis for cohesive materials filled on purely cohesive undrained clay

Stability charts for soil slopes were first produced by Taylor in 1937 and they continue to be used extensively as design tools and draw the attention of many investigators. From a review of literature, it was found that there is no convenient solution has been provided for cohesive materials filled on purely cohesive undrained clay. A recent study revealed that the embankment slope which has two-layered clays failed in an undrained state which shows the importance of this study. In order to obtain the solutions for this type of fill slope. A number of numerical method are employed, namely the finite element upper and lower bound limit analysis methods and limit equilibrium method. The numerical upper and lower bound limit analysis method can bracket true solutions within a small range (6%). The solutions of limit equilibrium analysis are used for comparison purpose.

An organic ionic plastic crystal electrolyte for rate capability and stability of ambient temperature lithium batteries

Reliable, safe and high performance solid electrolytes are a critical step in the advancement of high energy density secondary batteries. In the present work we demonstrate a novel solid electrolyte based on the organic ionic plastic crystal (OIPC) triisobutyl(methyl)phosphonium bis(fluorosulfonyl)imide (P1444FSI). With the addition of 4 mol% LiFSI, the OIPC shows a high conductivity of 0.26 mS cm-1 at 22 °C. The ion transport mechanisms have been rationalized by compiling thermal phase behaviour and crystal structure information obtained by variable temperature synchrotron X-ray diffraction. With a large electrochemical window (ca. 6 V) and importantly, the formation of a stable and highly conductive solid electrolyte interphase (SEI), we were able to cycle lithium cells (LiLiFePO4) at 30 °C and 20 °C at rates of up to 1 C with good capacity retention. At the 0.1 C rate, about 160 mA h g-1 discharge capacity was achieved at 20 °C, which is the highest for OIPC based cells to date. It is anticipated that these small phosphonium cation and [FSI] anion based OIPCs will show increasing significance in the field of solid electrolytes.

Enhancing thermal stability and mechanical properties of lyotropic liquid crystals through incorporation of a polymerizable surfactant.

We present a facile method to prepare thermally stable and mechanically robust crosslinked lyotropic liquid crystals (LLCs) through incorporation of a polymerizable amphiphile into a binary LLC system comprising commercially available surfactant Brij 97 and water. Thermal stability and mechanical properties of the polymerized LLCs were significantly enhanced after polymerization of the incorporated polymerizable surfactant. The effect of incorporating a polymerizable amphiphile on the phase behavior of the LLC system was studied in detail. In situ photo-rheology was used to monitor the change in the mechanical properties of the LLCs, namely the storage modulus, loss modulus, and viscosity, upon polymerization. The retention of the LLC nanostructures was evaluated by small angle X-ray scattering (SAXS). The ability to control the thermal stability and mechanical strength of LLCs simply by adding a polymerizable amphiphile, without tedious organic synthesis or harsh polymerization conditions, could prove highly advantageous in the preparation of robust nanomaterials with well-defined periodic structures.