FTIR and thermal analysis of cashmere and other animal fibres

In this paper, sereval varieties of animal fibres including cashmere and Australian fine Merino wool have been analysed by Fourier transform infrared microscope and differential scanning calorimeter. The results showed that both Chinese and Australian cashmere fibres started absorbing heat at a relatively higher temperature but were thermally degraded quicker than other animal fibres tested. However, the mass changes (within the temperature range of 200oC to 350oC) and associated onset temperatures varied among fibre varieties. From the attenuated total reflectance spectra, the Chinese cashmere was clearly different from Australian cashmere and wool in a peak near 1040 cm-1 wavelength for S-O stretching of cysteic acid residues. The Chinese cashmere presented a stronger absorption at 1019 cm-1 wavelength, while Australian cashmere and wool peaked at 1079 cm-1 wavelength and had a weaker absorption. Combined with thermal analysis, the normalised R-SO3 - content of cysteic acid residues to the amide II peak of the protein backbone may have potential use in identifying Australian fine Merino wool from Chinese cashmere.

Computational thermal analysis of a continuous flow micro Polymerase Chain Reaction (PCR) chip

The first continuous flow micro PCR introduced in 1998 has attracted considerable attention for the past several years because of its ability to amplify DNA at much faster rate than the conventional PCR and micro chamber PCR method. The amplification is obtained by moving the sample through 3 different fixed temperature zones. In this paper, the thermal behavior of a continuous flow PCR chip is studied using commercially available finite element software. We study the temperature uniformity and temperature gradient on the chip’s top surface, the cover plate and the interface of the two layers. The material for the chip body and cover plate is glass. The duration for the PCR chip to achieve equilibrium temperature is also studied.

A study on the formation of MgAl2O4 and MgO crystals in Al-Mg/quartz composite by differential thermal analysis

The present study has examined the thermodynamics of MgAl₂O₄ and MgO formations in Al–Mg alloy/quartz (>99% crystalline silica) through differential thermal analysis (DTA). The formation of MgAl₂O₄ and MgO is detected as exothermic peaks in the heat flow curve and the reaction is confirmed by the Si dissolution peaks observed during the reheating of samples and SEM analysis of the reacted sample. The presence of MgAl₂O₄ and MgO is confirmed in the XRD analysis of the reacted sample. The study has enabled the production of nano sized MgAl₂O₄ and MgO crystals at the interface of Al–Mg alloy and quartz. The reaction between them is found to be influenced by the oxidation of Mg, which is reduced by increasing heating rates.

High-performance composite from epoxy and glass fibers : morphology, mechanical, dynamic mechanical, and thermal analysis

Diglycidyl ether of bisphenol-A type epoxy resin cured with diamino diphenyl sulfone was used as the matrix for fiber-reinforced composites to get improved mechanical and thermal properties for the resulting composites. E-glass fiber was used for fiber reinforcement. The morphology, tensile, flexural, impact, dynamic mechanical, and thermal properties of the composites were analyzed. The tensile, flexural, and impact properties showed dramatic improvement with the addition of glass fibers. Dynamic mechanical analysis was performed to obtain the Tg of the cured matrix as well as the composites. The improved thermal stability of the composites was clear from the thermogravimetric analysis. Scanning electron micrographs were taken to understand the interfacial adhesion between the fiber and the matrix. The values of mechanical properties were compared with modified epoxy resin composite system. Predictive models were applied using various equations to compare the mechanical data obtained theoretically and experimentally.

Dynamic mechanical thermal analysis studies of factors influencing relaxation in polyetherurethane based solid electrolytes

Dynamic mechanical thermal analysis (DMTA) has been used to study the effects of plasticizers on the mobility and homogeneity of a series of solid polymer electrolytes (SPEs). With reference to previously published results on similar systems containing LiClO₄ salts and tetraglyme as plasticizer, the effects of propylene carbonate (PC) on the glass transition temperature (T_g) of the SPE and on the distribution of relaxation times within the sample are discussed; at low plasticizer concentration PC has little effect on T_g as measured by DMTA in comparison with tetraglyme, and at higher plasticizer concentrations PC significantly broadens the mechanical relaxation behaviour indicating a greater degree of dynamical heterogeneity within the sample. A second low temperature relaxation is evident at lower PC contents indicating that some regions of this plasticized SPE are distinctly more mobile than others or perhaps, on this length scale, that some degree of phase separation is present. Activation energies for the mechanical relaxation were also determined as a function of PC concentration and are significantly greater than those determined from conductivity measurements.

Thermal analysis of nanofluids in microfluidics using an infrared camera

We present the thermal analysis of liquid containing Al2O3 nanoparticles in a microfluidic platform using an infrared camera. The small dimensions of the microchannel along with the low flow rates (less than 120 μl min−1) provide very low Reynolds numbers of less than 17.5, reflecting practical parameters for a microfluidic cooling platform. The heat analysis of nanofluids has never been investigated in such a regime, due to the deficiencies of conventional thermal measurement systems. The infrared camera allows non-contact, three dimensional and high resolution capability for temperature profiling. The system was studied at different w/w concentrations of thermally conductive Al2O3 nanoparticles and the experiments were in excellent agreement with the computational fluid dynamics (CFD) simulations.

Different thermal analysis technique application in determination of fold surface-free energy

In this work, the crystallization rates and spherulitic growth rate of miscible blends of poly(vinylidene fluoride) (PVDF) and acrylic rubber (ACM) were determined using differential scanning calorimetry (DSC), real-time FTIR, and optical microscopy. FTIR results suggest that blending does not induce the creation of polymorphic crystalline forms of PVDF. SAXS data demonstrate the formation of interlamellar structure after blending. The fold surface-free energy (σ e) was analyzed and compared using different thermal analysis techniques. The isothermal crystallization curves obtained using real-time FTIR and DSC explored in two different methods: t 1/2 or Avrami equation. While the Avrami equation is more widespread and precise, both analytical methods gave similar free energy of folding values. However, it was found that the direct optical method of measuring spherulitic growth rate yields σ e values 30-50 % lower than those obtained from the overall crystallization rate data. Conversely, the σ e values were found to increase with increasing amorphous ACM phase content regardless of the analytical methods.

Studies on the properties and the thermal decomposition kinetics of natural rubber prepared with calcium chloride

To evaluate calcium chloride coagulation technology, two kinds of raw natural rubber samples were produced by calcium chloride and acetic acid respectively. Plasticity retention index (PRI), thermal degradation process, thermal degradation kinetics and differential thermal analysis of two samples studied. Furthermore, thermal degradation activation energy, pre-exponential factor and rate constant were calculated. The results show that natural rubber produced by calcium chloride possesses good mechanical property and poor thermo-stability in comparison to natural rubber produced by acetic acid.

Thermal degradation kinetics and mechanism of epoxidized natural rubber

Thermal resistance is one of the most dominative properties for polymer materials. Thermal degradation mechanisms of epoxidized natural rubber (ENR) and NR are studied by thermogravimetric analysis (TGA) and differential thermal analysis (DTA). The results show that, the introduction of epoxy groups into the NR molecular main chain leads to a remarkable change in the degradation mechanism. The thermal stability of ENR is worse than that of NR. For the first thermooxidative degradation stage, the thermal decomposition mechanism of ENR is similar to that of NR, which corresponds to a mechanism involving one-dimensional diffusion. For the second stage, the thermal decomposition mechanism of ENR is a three-dimensional diffusion, which is more complex than that of NR. Kinetic analysis showed that activation energy (E?), activation entropy (?H) and activation Gibbs energy (?G) values are all positive, indicating that the thermooxidative degradation process of ENR is non-spontaneous.

Rapid composite tube manufacture utilizing the quickstep™ process

In this study, a novel method for manufacturing composite tubes utilizing the Quickstep^TM process has been developed. Tubes manufactured from `quick-cure' Toray G83C prepreg have demonstrated highly repeatable axial crush behavior with an average specific energy absorption (SEA) of 86 kJ/kg. The cure cycle is optimized by comparing the results from compression, dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC), and porosity testing. The tube lay-up is optimized using compression and porosity test results. The effect of changes in fiber-orientation on SEA is also investigated. Process development has resulted in a robust manufacturing method capable of producing fully cured, high performance composite tubes with a cure cycle of 7 min. This corresponds to a 95% reduction in time compared to an equivalent autoclave cycle.

Effect of crystallization on corrosion resistance of Cu52.5Ti30Zr11.5Ni6 bulk amorphous alloy

The effects of crystallization on the corrosion resistance of a  Cu52.5Ti30Zr11.5Ni6 bulk amorphous alloy in 1 mol/L HCl, and 6 mol/L NaOH solutions were studied. The amorphous alloy was identified by  differential thermal analysis(DSC) and by X-ray diffraction(XRD). The partially and fully crystallized alloys were prepared by controlling the annealing  temperatures at 738 and 873 K for 1 and 12 min, respectively, and the corrosion resistances of those annealed alloys were compared with that of the amorphous alloy by immersion test and potentiodynamic measurements in 1 mol/L HCl and 6 mol/L NaOH solutions. The results show that the  partially crystallized alloy exhibits high corrosion resistance, whereas full crystallization results in deteriorated corrosion resistance compared with that of the as-cast amorphous alloy.

Inorganic-organic hybrids of the p,p'-diphenylmethylenediphosphinate ligand with bivalent metals: a new 2D-layered phenylphosphinate zinc(II) complex

By reaction of Zn(CH₃COO)₂ with p,p′-diphenylmethylenediphosphinic acid in water a new inorganic–organic polymeric hybrid of formula [Zn(CH₂(P(Ph)O₂)₂)] has been synthesized and completely characterized. The X-ray analysis established that the structure consists of 2D-layered polymeric array, the 2D-sheets being built up through strong covalent linkages between the zinc metal and the oxygen donors of the phenylphosphinate ligand. The 2D-layers, which are featuring a mesh-net fashion, present voids of various dimensionality, up to 24-membered rings. The organic parts of the hybrid ligand, namely the phenyl rings, are shielding the inorganic skeleton of the layers, preventing the propagation of the polymer in the third dimension. No water molecules are present in the lattice, both of coordination and crystallization. Crystal data are: monoclinic, P2₁Ic, a=11.840(2), b=9.646(9), c=12.516(5) Å, β=95.03(2), V=1423.9(15) ų, Z=4. The solid material has been characterized by ³¹P MAS NMR spectroscopy and thermogravimetric analysis.

Modification of wool fiber using steam explosion

Wool fiber was modified by steam explosion in this study. SEM results show that some scales on the fiber surface were cleaved and tiny grooves generated during the explosion. FTIR results suggest no evident changes in the chemical composition of the fiber after the explosion treatment. However, the crystallinity of the fiber decreased slightly as the steam pressure increased based on the X-ray results. In the thermal analysis, DSC results show that the temperature corresponding to vaporization of absorbed water and cleavage of disulfide bonds respectively decreased as the steam pressure increased. The reduction in thermal decomposition energy of the treated fiber indicates that steam explosion might have destroyed some crystals and crosslinks of macromolecular chains in the fiber. The treatment also led to some alterations of the fiber properties, including reduction in strength, moisture regain and solubility in caustic solution.