The influence of solute carbon in cold-rolled steels on shear band formation and recrystallization texture

Two experiments were conducted to clarify the roles of grain size, solute carbon and strain in determining the recrystallization textures of cold-rolled and annealed steels. In the first experiment, samples of coarse-grained low-carbon (LC) and interstitial-free (IF) steels were cold-rolled to a 75% reduction in thickness. One sample from each steel was polished and cold-rolled an additional 5%, while the remaining samples were annealed for various times at 650°C. In the second experiment, three samples from a commercial LC steel sheet were rolled 70% at 300°C. Two of the samples were given a further rolling reduction of 5% of the original thickness, with one of the samples being given this additional reduction at 300°C and the other at room temperature. Goss recrystallization textures are strengthened by coarse initial grain sizes, the presence of solute carbon and rolling at a temperature where dynamic strain ageing occurs, but are weakened by additional rolling beyond a reduction of 70%, especially when this extra rolling is conducted at a temperature where dynamic strain ageing does not occur. Characterization of key features of the deformed and recrystallized steels using optical microscopy, scanning electron microscopy (SEM) and electron back-scatter diffraction (EBSD) supports a rationale for these effects based on the repeated activation and deactivation of shear bands and the influence of solute carbon and dynamic strain ageing on the operating life of the bands and the accumulation of strain within them.

Development of adiabatic shear band in cold-rolled titanium

The evolution of adiabatic shear localization in commercial titanium subjected to heavy cold rolling was investigated. The evolution of the morphology, microhardness, local shear strain, and local temperature increments were systematically studied and estimated. A shear band with about 25m in width was formed and fine nanograins with a range of dimensions varying from 20 to 160nm and had a mean size of about 70nm were observed inside the centre of shear band after 83% cold-rolling. Microhardness test shows that hardness within the shear band is markedly higher than that of the surrounding matrix. The calculated shear strain and maximum temperature increase within the shear band are much higher than that of the overall deformed sample. The initiation of shear localization may depend on geometric perturbation instead of thermal ones.

Effect of relaxation on pressure sensitivity index in a Zr-based metallic glass

Shear-banding features of as-cast and annealed Zr_41.2Ti_13.8Cu_12.5Ni₁₀Be_22.5 bulk metallic glass were investigated through Rockwell indentation tests. Isothermal annealing of the as-cast samples was conducted at temperatures below its glass transition temperature, Tg. The exothermal enthalpy during continuous heating below Tg decreases with increasing annealing temperature, indicating the gradual reduction of free-volume upon annealing. The observation on the morphology of shear-banding pattern around the indents implies a reduced shear bands activity in the annealed samples. The included angles (2θ) between two families of shear bands emanating from the edge of Rockwell indent decrease from 88° for the as-cast sample to 79° for the sample annealed at 633 K for 1 h, indicating a pressure sensitive plasticity. By Mohr–Coulomb criterion, the pressure sensitive index can be obtained on the basis of the measured 2θ, which increases with increasing annealing temperature, indicating an increase of “atomistic friction” due to the reduction of the free volume upon annealing.

Transmission electron microscopy characterization of the bake-hardening behavior of transformation-induced plasticity and dual-phase steels

The effect of prestraining (PS) and bake hardening (BH) on the microstructures and mechanical properties has been studied in transformation-induced plasticity (TRIP) and dual-phase (DP) steels after intercritical annealing. The DP steel showed an increase in the yield strength and the appearance of the upper and lower yield points after a single BH treatment as compared with the as-received condition, whereas the mechanical properties of the TRIP steel remained unchanged. This difference appears to be because of the formation of plastic deformation zones with high dislocation density around the “as-quenched” martensite in the DP steel, which allowed carbon to pin these dislocations, which, in turn, increased the yield strength. It was found for both steels that the BH behavior depends on the dislocation rearrangement in ferrite with the formation of cell, microbands, and shear band structures after PS. The strain-induced transformation of retained austenite to martensite in the TRIP steel contributes to the formation of a complex dislocation structure.

Indentation study on the pressure sensitivity of a ZR-based bulk metallic glass

Spherical indentation test was conducted on as-cast and annealed Zr_41.2Ti_13.8Cu_12.5Ni₁₀Be_22.5 bulk metallic glass, and the evolution of the morphology of the deformation zone of indents upon annealing was investigated. The DSC traces of the as-cast and annealed samples show that the enthalpy change at the glass transition, ΔH, decreases with the increasing of annealing temperature, indicating the reduction of the free volume upon annealing. The morphology of the indents implies a reduced shear band activity in the annealed samples. The included angles (2θ) between two families of shear bands emanating from the edge of spherical indent in the as-cast and the annealed samples were measured to be in the range of 88-79°, which decrease with the increasing of annealing temperature, indicating pressure sensitive plasticity in the as-cast and annealed samples. By Mohr–Coulomb criterion, the pressure sensitive index, α, can be obtained on the basis of the measured 2θ. The sensitivity index increases with increasing temperature, implying an increase of 'atomistic friction' due to the reduction of the free volume upon annealing.

Plastic deformation in Zr41 Ti14 Cu12.5 Ni10 Be22.5 bulk metal glass under vickers indenter

Vickers indentation was conducted on an as-cast Zr41Ti14Cu12.5Ni10Be22.5 bulk metal glass (BMG) to study shear band formation using a bonded interface technique. The results indicate that the plastic deformation in the BMG is accommodated by the semi-circular (primary) and radial (secondary) shear bands. The inter-band spacing of the semi-circular shear bands is found to be independent of the applied load. The measured size of the deformation zone is in good agreement with the prediction of the theoretical model proposed by Zhang et al.

Effect of structure relaxation on the plastic deformation behaviour in a Zr-based BMG under indenter

Vickers and nano indentations were performed on a structurally relaxed Zr₄₁Ti₁₄Cu_12.5Ni₁₀Be_22.5 bulk metallic glass (BMG), and the evolution of the shear bands in the relaxed BMG was investigated and compared to that in the as-cast alloy. Results indicate that the plastic deformation in the BMG with structure relaxation is accommodated by the semicircular (primary) and radial (secondary) as well as tertiary shear bands. Quantitatively, the shear band density in the relaxed alloy was much lower than that in the as-cast alloy. The annihilation of free volume caused by the annealing was responsible for the embrittlement of the sample with structure relaxation.

Plastic deformation in the annealed Zr41Ti14Cu12.5Ni10Be22.5 bulk metal glass under indenter

Vickers and nanoindentationswere carried out on an annealed Zr₄₁Ti₁₄Cu_12.5Ni₁₀Be_22.5 bulk metallic glass (BMG), and the evolution of the shear bands in the annealed BMG was investigated and compared to that in the as-cast alloy. Results indicate that the plastic deformation in the BMG with the structure relaxation is accommodated by the semicircular (primary) and radial (secondary) as well as tertiary shear bands. Quantitatively, the shear band density in the annealed alloywas much lower than that in the as-cast alloy. The load-displacement curve of nanoindentation test for the annealed alloy exhibited a more flat serrated flow. The annihilation of free volume caused by the annealing was responsible for the embrittlement of the annealed sample.

Plastic deformation in a partially crystallized Zr-based BMG under Vickers indenter

Vickers indentations were carried out on an anneal-introduced partially crystallized Zr₄₁Ti₁₄Cu_12.5 Ni₁₀Be_22.5 bulk metallic glass (BMG), and the evolution of the shear bands in this samplewas investigated and compared to the as-cast, aswell as the structurally relaxed counterparts. The results indicate that the plastic deformation in the partially crystallized BMG was accommodated by the semi-circular (primary) and radial (secondary) shear bands. A full crack or flake that was produced due to the spring back during the load removal was observed. The shear band density in the annealed alloy which was dispersed with crystalliteswas significantly lower than that of the as-cast alloy. The difference of the shear band features among the three kinds of alloy status, i.e., partially crystallized, structurally relaxed and as-cast alloys was discussed in terms of the free volume in the BMGs and the characteristics of nano-composites. It has been demonstrated that the plasticity for the three statuses of alloys queues in the descending order as the as-cast, annealed with partial crystallization, and annealed without crystallization.

Microstructural and magnetic properties of Nd-Fe-B alloys processed by equal-channel angular pressing

Equal-channel angular pressing (ECAP) is a well-established thermo-mechanical processing technique. This technique allows virtually unlimited strain and manipulation of texture by processing route, while the cross-section of the sample remains unchanged during processing. In order to clarify the effectiveness of ECAP on preparing anisotropic permanent magnets, the microstructure and magnetic properties of a melt-spun Nd13.5Fe73.8Co6.7B5.6Ga0.4 alloy processed at 773-K for 300-s by ECAP were investigated. Macrotexture analysis carried out for the exit channel of ECAP shows that the basal plane of the tetragonal Nd2Fe14B crystal aligns parallel to the shear band, i.e., the c-axis texture formation normal to the shear band induced by the ECAP process. Due to this texture formation, the technical magnetization behaviour becomes anisotropic, and the remanent magnetization is clearly enhanced along the direction perpendicular to the shear band. This anisotropic microstructure is realized at a relatively low processing temperature of 773-K, well below the melting point of the Nd-rich intergranular phase. As a consequence of this lower processing temperature, the nanostructure of the melt-spun alloy remains approximately 20 to 30-nm, considerably smaller than the typical grain size obtained after conventional die-upsetting. Our study demonstrates that equal-channel angular pressing has a potential for realising anisotropic nanostructured magnets.

Machining of coarse grained and ultra fine grained titanium

Machining of titanium is quite difficult and expensive. Heat generated in the process of cutting does not dissipate quickly, which affects tool life. In the last decade ultra fine grained (UFG) titanium has emerged as an option for substitution for more expensive titanium alloys. Extreme grain refinement can be readily performed by severe plastic deformation techniques. Grain refinement of a material achieved in this way was shown to change its mechanical and physical properties. In the present study, the microstructure evolution and the shear band formation in chips of coarse grained and UFG titanium machined to three different depths and three different feeding rates was investigated. A change in thermal characteristics of commercial purity Ti with grain refinement was studied by comparing heating/cooling measurements with an analytical solution of the heat transfer boundary problem. It was demonstrated that an improvement in the machinability can be expected for UFG titanium. © 2012 Springer Science+Business Media, LLC.

Strain localisation patterns under equal-channel angular pressing

Instabilities of plastic flow in the form of localised shear bands were experimentally observed to result from equal-channel angular pressing (ECAP) of magnesium alloy AZ31. The appearance of shear bands and their spacing were dependent on velocity of the pressing and applied back-pressure. A generic gradient plasticity theory involving second-order strain gradient terms in a constitutive model was applied to the case of AZ31 deformed by ECAP. Linear stability analysis was applied to the set of equations describing the deformation behaviour in the process zone idealised as a planar shear zone. A full analytical solution providing a dispersion relation between the rate of growth of a perturbation and the wave number was obtained. It was shown that the pattern of incipient localised shear bands exhibits a spectrum of characteristic lengths corresponding to admissible wave numbers. The interval of the spectrum of wave numbers of viable, i.e. growing, perturbations predicted by linear stability analysis was shown to be in good agreement with the experimentally observed spectrum. The effect of back-pressure applied during ECAP was also considered. The predicted displacement of the shear band spectrum towards lower wave numbers, shown to be a result of the decreased shear strain rate in the shear zone, was consistent with the experimentally observed increase of the band spacing with increased back-pressure. A good predictive capability of the general modelling frame used in conjunction with linear stability analysis was thus demonstrated in the instance of the particular alloy system and the specific processing conditions considered.