Properties of hemp fibre reinforced concrete composites

This research is concerned with the mechanical and physical properties of hemp fibre reinforced concrete (HFRC). An experimental program was developed based on the statistical method of fractional factors design. The variables for the experimental study were: (1) mixing method; (2) fibre content by weight; (3) aggregate size; and (4) fibre length. Their effects on the compressive and flexural performance of HFRC composites were investigated. The specific gravity and water absorption ratio of HFRC were also studied. The results indicate that the compressive and flexural properties can be modelled using a simple empirical linear expression based on statistical analysis and regression, and that hemp fibre content (by weight) is the critical factor affecting the compressive and flexural properties of HFRC.

Experimental study of dynamic compressive behaviour of concrete material reinforced with spiral steel fibres

It has been well demonstrated that the impact loading resistance capacity of the concrete material can be effectively increased by adding fibres. Recent studies proved that compared to other conventional steel fibres, using steel fibres with spiral shape further increases the post-failure energy absorption and crack stopping capacities of concrete because of the better bonds in the concrete matrix and larger deformation ability. The present study conducts high rate impact tests using split Hopkinson pressure bar (SHPB) to further investigate the dynamic compressive properties of spiral fibre reinforced concrete (SFRC). SFRC specimens with different volume fractions of fibres ranging from zero to 1.5% are prepared and tested. The influences of different volume fractions of fibres on strength, stress-strain relation and energy absorption of SFRC specimens under quasi-static and dynamic loadings are studied. In SHPB compression tests, the strain rate achieved ranges from 50 1/s to 200 1/s. Highspeed camera is used to capture the failure processes and failure modes of SFRC specimens with different fibre volume fractions during the tests for comparison. Dynamic stress-strain curves under different strain rates are derived. The energy absorption capacities of the tested specimens are obtained and compared. Strain rate effects on the compressive strength are also discussed. The corresponding empirical DIF (dynamic increase factor) relations for SFRC are proposed.

A simple displacement-based quadrilateral laminated composite plate element - part I : linear analysis

Based on the first-order shear deformation theory (FSDT) and Timoshenko's laminated composite beam functions, a simple displacement-based 4-node, 24-dof quadrilateral laminated plate element is proposed in this paper for linear analysis of thin to moderately thick laminates. The deflection and rotation functions of the element boundary are obtained from the Timoshenko's laminated composite beam functions, hence convergence to the thin plate solution can be achieved theoretically and shear-locking problem is avoided naturally. The in-plane displacement functions of a quadrilateral plane element with drilling degrees of freedom are taken as the in-plane displacements of the proposed quadrilateral element. Some numerical examples of linear analysis of composite laminated plates are calculated, and the results show that the proposed element is convergent, shear-locking free, efficient, accurate and not sensitive to mesh distortion.

A simple displacement-based quadrilateral laminated composite plate element : Part II : linear analysis

The 4-node, 24-dof quadrilateral displacement-based element (Zhang et al. 2004), which have been developed successfully for linear analysis of thin to thick laminated composite plates, is extended further for geometrically nonlinear analysis in this paper. The proposed element is based on the first-order shear deformation theory (FSDT) and von-Karman's large deflection theory, and the total Lagrangian approach is employed to formulate the element. The deflection and rotation functions of the element boundary are obtained from Timoshenko's laminated composite beam functions. The developed element is simple in formulation, free from shear-locking, and include conventional engineering degrees of freedom. Numerical examples demonstrate that the element is accurate and efficient for large deformation, small rotation geometrically nonlinear analysis of thin to moderately thick laminated composite plates.

Transient response analysis of steel in concrete

A new approach is presented for the analysis of galvanostatically induced transients allowing for the rapid evaluation of the corrosion activity of steel in concrete. This method of analysis is based on the iterative fitting of a non-exponential model based on a modified KWW (Kohlrausch–Williams–Watt) formalism. This analysis yields values for the parameters related to corrosion such as the concrete resistance, polarisation resistance, interfacial capacitance and β, the non-ideality exponent.

Integrated health monitoring for reinforced concrete beams: an experimental study

Civil infrastructures begin to deteriorate once they are built and used. Detecting the damages in a structure to maintain its safety is a topic that has received considerable attention in the literature in recent years. In vibration-based methods, the first few modes are used to assess the locations and the amount of damage. However, a small number of the global modes are not sufficient to reliably detect minor damage in the structure. Also, a common limitation of these techniques is that they require a high-fidelity model of the structure to start with, which is usually not available. Recently, guided waves (GW) have been found as an effective and efficient way to detect incipient damages due to its capacity of relatively long propagation range as well as its flexibility in selecting sensitive mode-frequency combinations. In this paper, an integrated structural health monitoring test scheme is developed to detect damages in reinforced concrete (RC) beams. Each beam is loaded at the middle span progressively to damage. During each loading step, acoustic emission (AE) method is used as a passive monitoring method to catch the AE signals caused by the crack opening and propagation. After each loading step, vibration tests and guided wave tests are conducted as a combined active monitoring measure. The modal parameters and wave propagation results are used to derive the damage information. Experimental results show that the integrated method is efficient to detect incipient damages in RC structures.

Monitoring corrosion of reinforced concrete beams in a chloride containing environment under different loading levels

Corrosion has significant adverse effects on the durability of reinforced concrete (RC) structures, especially those exposed to a marine environment and subjected to mechanical stress, such as bridges, jetties, piers and wharfs. Previous studies have been carried out to investigate the corrosion behaviour of steel rebar in various concrete structures, however, few studies have focused on the corrosion monitoring of RC structures that are subjected to both mechanical stress and environmental effects. This paper presents an exploratory study on the development of corrosion monitoring and detection techniques for RC structures under the combined effects of external loadings and corrosive media. Four RC beams were tested in 3% NaCl solutions under different levels of point loads. Corrosion processes occurring on steel bars under different loads and under alternative wetting - drying cycle conditions were monitored. Electrochemical and microscopic methods were utilised to measure corrosion potentials of steel bars; to monitor galvanic currents flowing between different steel bars in each beam; and to observe corrosion patterns, respectively. The results indicated that steel corrosion in RC beams was affected by local stress. The point load caused the increase of galvanic currents, corrosion rates and corrosion areas. Pitting corrosion was found to be the main form of corrosion on the surface of the steel bars for most of the beams, probably due to the local concentration of chloride ions. In addition, visual observation of the samples confirmed that the localities of corrosion were related to the locations of steel bars in beams. It was also demonstrated that electrochemical devices are useful for the detection of RC beam corrosion.

Compressive and flexural properties of hemp fiber reinforced concrete

The compressive and flexural properties of hemp fiber reinforced concretes (FRC) were examined in this paper. Natural hemp fiber was mixed using dry and wet mixing methods to fabricate the FRC. Mechanical properties of the FRC were investigated. The main factors affecting compressive and flexural properties of the FRC materials were evaluated with an orthogonal test design. Fiber content by weight has the largest effect. The method for casting hemp FRC has been optimised. Under the optimum conditions, compressive strength increased by 4 %, flexural strength increased by 9 %, flexural toughness increased by 144 %, and flexural toughness index increased by 214 %.

Concentration monitoring and performance of a migratory corrosion inhibitor in steel-reinforced concrete

Inhibitor concentration depth profiles for concrete samples treated with a proprietary migratory corrosion inhibitor (of the Cortec MCI range) are presented. The treated concrete was cored and these cores were then sectioned and crushed before being immersed in distilled water to extract the available inhibitor. The amine concentrations were quantified using an ammonium-sensing electrode and were then related to the inhibitor concentration present. The inhibitor examined, reported to contain a combination of volatile amines and amino carboxylate compounds, was found to readily diffuse through concrete. The inhibitor was subjected to a 5-year trial and found to be effective in suppressing corrosion of steel reinforcement in the presence of high chloride concentrations. The concentration profiles indicate that only relatively low concentrations of inhibitor were required to achieve inhibition in this case.