The determination of the local conditions for void initiation in front of a crack tip for materials with second-phase particles

A procedure is proposed to determine, for second-phase particles near a crack tip, the maximum particle stresses at the moment of void initiation by either particle fracture or particle/matrix interface separation. A digital image analysis system is applied to perform a quantitative analysis of corresponding fracture surface regions from stereo image pairs taken in the scanning electron microscope. The fracture surface analysis is used to measure, for individual particles, the crack tip opening displacement at the moment of void initiation and the particle location with respect to the crack tip. From these data, the stress tensor at the moment of void initiation is calculated from the Hutchinson–Rice–Rosengren (HRR) field theory. The corresponding average local stresses within the particle are evaluated by a non-linear Mori–Tanaka-type approach. These stresses are compared to estimates according to the models by Argon et al. [A.S. Argon, J. Im, R. Safoglu, Metall. Trans. 6 (1975) 825] and Beremin [F.M. Beremin, Metall. Trans. 12 (1981) 723]. The procedure is demonstrated on an Al6061–10% Al2O3 metal matrix composite.

Effect of second-phase particles on shape memory in Fe-Mn-Si-based alloys

The shape memory behaviour of two Fe–Mn–Si-based alloys has been investigated. One alloy was a reference alloy, and the other alloy was
similar in composition except that it contained 0.55 wt% Ti. Following solution treatment and quenching, strip samples were subjected to three types
of treatments; isothermal holding, cold rolling followed by isothermal holding, and hot rolling followed by isothermal holding. These treatments
resulted in the formation of intermetallic precipitates in the Ti-containing alloy, while the reference alloy remained precipitate-free. In comparing
the shape memory of the reference and the particle-containing alloy after identical heat treatments, it was found that the formation of precipitates
had a beneficial effect on the shape memory in all cases. In general, the larger precipitates caused a larger increase in the shape memory. The effect
of particle size on shape memory has been analysed using the current data and published results for a range of precipitate types.

On the impact of second phase particles on twinning in magnesium alloys

Deformation twinning is an important deformation mode in magnesium alloys. Despite this, little is known on the extent to which the stress for twinning can be altered by a dispersion of second phase particles. The current paper presents a series of findings on the role of differently shaped particles on both the stress required for twinning and the characteristics of the twins that form. It is shown that plate shaped particles are, as one might expect, an effective strengthener to {10-12} twinning. When precipitate plates form on the basal planes, the relative hardening of basal slip is minor in comparison to that seen for twinning. This provides opportunity for the alloy designer to control the apparent critical resolved shear stresses (CRSS) for the different deformation modes. Possible sources for the hardening of twins are discussed.

Structural phase transformations of Mg3N2 at high pressure : experimental and theoretical studies

The structural behavior of Mg₃N₂ has been investigated up to 40.7 GPa at room temperature by means of angle-dispersive X-ray diffraction. A reversible, first-order structural phase transition from the ambient cubic phase (Ia3̅) to a high-pressure monoclinic phase (C2/m) is found to start at ~ 20.6 GPa and complete at ~ 32.5 GPa for the first time. The equation of state determined from our experiments yields bulk moduli of 110.7(2) and 171.5(1) GPa for the cubic and monoclinic phases, respectively, indicating higher incompressibility of the high-pressure phase of Mg₃N₂. First-principles calculations reproduced the phase stability and transition pressure determined in our experiment. In addition, a second phase transition from the monoclinic phase to a hexagonal phase (P3̅m₁) was predicted around 67 GPa for Mg₃N₂. The electronic band structures of three phases of Mg₃N₂ are also calculated and discussed.

Phase dissolution of γ-Mg17Al12 during homogenization of As-Cast AZ80 magnesium alloy and its effect on room temperature mechanical properties

As-cast AZ80 Mg alloy contains α-Mg, partially divorce eutectic of α and γ (Mg 17Al 12), fully divorce eutectic of α and γ, and lamellar eutectic of α and γ phases. During homogenization, second phase (γ-Mg 17Al 12) gets dissolved can change the mechanical properties. Therefore, the aim of the present work is to bring out the kinetics of dissolution of γ phase and evaluate its effect on mechanical properties. Microstructure evolution during homogenization was investigated as a function of time for 0.5 to 100 h and at the temperatures of 400° and 439°C. In as-cast state, this material was found to contain 70% α-Mg and 30% eutectic phase. With increasing homogenization time, dissolution of lamellar eutectic occurs first which is followed by dissolution of fully divorce eutectic and partially divorce eutectic. The dissolution kinetics of γ phase was analyzed based on the decrease in its volume fraction as a function of time. The time exponent for dissolution was found to be 0.38 and the activation energy for the dissolution of γ phase was found to be 84.1 kJ/mol. This dissolution of γ phase leads to decrease in hardness and tensile strength with increase in homogenization time.

A study of phase behavior and conductivity of mixtures of the organic ionic plastic crystal N-methyl-N-methyl-pyrrolidinium dicyanamide with sodium dicyanamide

We report on the thermal, structural and conductivity properties of the organic ionic plastic crystal (OIPC) N-methyl-N-methyl-pyrrolidinium dicyanamide [C1mpyr][N(CN)2] mixed with the sodium salt Na[N(CN)2]. The DSC thermal traces indicate that an isothermal transition, which may be a eutectic melting, occurs at ~ 89 °C, below which all compositions are entirely in the solid phase. At 20 mol% Na[N(CN)2], this transition is the final melt for this mixture, and a new liquidus peak grows beyond 20 mol% Na[N(CN)2]. The III- > II solid-solid phase transition continues to be evident at ~- 2 °C. The microstructure for all the mixtures indicated a phase separated morphology where precipitates can be clearly observed. Most likely, these precipitates consist of a Na-rich second phase. This was also suggested from the vibrational spectroscopy and the 23Na NMR spectra. The lower concentrations of Na[N(CN)2] present complex 23Na MAS spectra, suggesting more than one sodium ion environment is present in these mixtures consistent with complex phase behavior. Unlike other OIPCs where the ionic conductivity usually increases upon doping or mixing in a second component, the conductivity of these mixtures remains relatively constant and above 10- 4 S cm- 1 at ∼ 80 °C, even in the solid state. Such high conductivities suggest these materials may be promising to be used for all solid-state electrochemical devices.

Effects of Mg17Sr2 Phase on the bio-corrosion behavior of Mg-Zr-Sr alloys

The effect of the second phase Mg17Sr2 on the biocorrosion behavior of Mg5ZrxSr (x = 0, 2, 5 wt%) alloys before and after solution treatment was investigated. Electrochemical impedance spectroscopy, cathodic polarization and hydrogen evolution were used to evaluate the biocorrosion of Mg5ZrxSr. We found that Mg17Sr2 precipitated on boundary zones and enhanced the galvanic effect, leading to a severer corrosion of the Mg matrix adjacent to Mg17Sr2. The corrosion subsequently spread gradually from the regions adjacent to the Mg17Sr2 to the central Mg matrix. However, a high volume fraction of Mg17Sr2 could also form a continuous network, isolate the Mg matrix and act as a barrier of corrosion.

The development of a screening questionnaire for childhood cruelty to animals

Childhood cruelty to animals may be a marker of poor prognosis amongst conduct disordered children. However, other than semistructured interviews with parents or children, there are no screening instruments for this behavior. The aim of this study was to develop such an instrument. In the first phase of the study, a parent-report questionnaire, Children's Attitudes and Behaviors Towards Animals (CABTA) was designed and piloted on 360 elementary school children, enabling community norms and a factor structure for the instrument to be derived. In the second phase, the questionnaire was completed by the parents of a small sample of children (N= 17) to establish its test-retest reliability. In the third phase of the study, the CABTA was completed by the parents of 19 children who had been diagnosed with either a Disruptive Behavioral Disorder or Attention Deficit Hyperactivity Disorder, and the results were compared with the outcome of a semistructured interview with parents regarding their child's behavior toward animals. The results of the various phases of the study indicated that the CABTA consists of two factors, Typical and Malicious Cruelty to animals, and is a reliable and valid tool for detecting childhood cruelty to animals. Possible use and adaptations of the CABTA as a screening instrument in clinical and community samples are discussed.

Laboratory model studies of flushing of trapped salt water from a blocked tidal estuary

Results are presented from a series of laboratory model studies of the flushing of saline water from a partially- or fully-closed estuary. Experiments have been carried out to determine quantitatively the response of the trapped saline volume to fresh water flushing discharges Q for different values of the estuary bed slope α and the density difference (∆ρ)_o between the saline and fresh water. The trapped saline water forms a wedge within the estuary and for maintained steady discharges, flow visualisation and density profile data confirm that its response to the imposition of the freshwater purging flow occurs in two stages, namely (i) an initial phase characterised by intense shear-induced mixing at the nose of the wedge and (ii) a relatively quiescent second phase where the mixing is significantly reduced and the wedge is forced relatively slowly down and along the bed slope. Scalings based upon simple energy balance considerations are shown to be successful in (i) describing the time-dependent wedge behaviour and (ii) quantifying the proportion of input kinetic energy converted into increasing the potential energy of the wedge/river system. Measurements show that the asymptotic value of the energy conversion factor increases with increasing value of the river Froude number Fr_o at small values of Fr_o, thereafter reaching a maximum value and a gradual decrease at the highest values of Fr_o. Dimensional analysis considerations indicate that the normalised, time-dependent wedge position (x_w)³(g')o/q² can be represented empirically by a power-law relationship of the form (x_w)[(g')_o/q²]^1/3 =C [(t)[(g')_o²/q]^1/3]"where the proportionality coefficient C is a function of both Fr_o and the slope angle α and the exponent n has a value of 0.24. Successful attempts are made to relate the model data to existing field observations from a microtidal estuary.

Experiments with multiple, intermittent periodic flushing flows confirm the importance of the starting phase of each flushing event for the time dependent behaviour of the saline wedge after reaching equilibrium in the intervals between such events. For the parameter ranges investigated and for otherwise-identical external conditions, no significant differences are found in the position of the wedge between cases of sequential multiple flushing flows and steady single discharges of the same total duration.

The role of human resource management (HRM) in Australian-Malaysian joint ventures

This article examines human resource management (HRM) for successful Australian-Malaysian joint ventures (JVs), on the basis of survey data and case studies. The findings suggest that each phase of JV development had its own pattern of HR practices. Three phases of development were distinguished - initiation, transitional, and maturational. The first phase involved selecting, recruiting and training a skilled workforce and formulating rudimentary human resource policies. Cultural differences were most marked in this phase. The second phase, after three years of operation, involved evolution of human resource policies better suited to local conditions, and more polycentric management staffing. The final phase, after six years of operation, saw the development of a distinctive human resources system, and the minimisation of cultural differences as an operational issue. In this phase there was also a move to more geocentric management staffing.

Effect of thermomechanical parameters on the critical strain for ultrafine ferrite formation through hot torsion testing

A C–Mn–V steel was used to study ultrafine ferrite formation (1–3 μm) through dynamic strain-induced transformation (DSIT) using hot torsion experiments. A systematic study determined the critical strain for the start of DSIT (C,DSIT), although this may not lead to a fully ultrafine microstructure. Therefore, the strain to produce an ultrafine ferrite (UFF) as final microstructure (C,UFF) during deformation was also determined. In addition, the effect of thermomechanical parameters such as deformation temperature, prior austenite grain size, strain rate and cooling rate on C,DSIT and C,UFF has been evaluated. DSIT ferrite nucleated on prior austenite grain boundaries at an early stage of straining followed by intragranular nucleation at higher strains. The prior austenite grain size affected the distribution of DSIT ferrite nucleation sites at an early stage of transformation and the subsequent coarsening behaviour of the grain boundary and intragranular ferrite grains during post-deformation cooling. Also, C,DSIT and C,UFF increased with an increase in the prior austenite grain size and deformation temperature. The post-deformation cooling had a strong effect not only on C,UFF but also the UFF microstructure (i.e. final ferrite grain size and second phase characteristics).

Grain refinement in steels through thermomechanical processing

The development of ultrafine grained microstructures in steels has received considerable attention in recent times. In many cases the aim is to produce high strength structural steels with minimal alloying. It is well established that for an equiaxed ferrite with a uniform dispersion of second phase, both the strength and toughness will be markedly improved if the grain size can be reduced to 1-2 μm, from the typical range of 5-10 μm. Means of achieving this through dynamic strain induced transformation are examined here, following a brief overview of some of the key issues encountered when attempting to refine the austenite in existing mill configurations. A number of deformation microstructure maps are developed to aid the discussion.

Making decisions: nursing practices in critical care

This article reports the types and complexity level of decisions made in everyday clinical practice by critical care nurses. It also reports factors that influence the complexity of those decisions. A combination of methods were chosen for the two phase study. In the first phase, 12 qualified critical care nurses documented decisions (over a 2 hour period) on a clinical decision recording form designed by the researcher. In the second phase, participants attended a semi-structured focus group.

From the analysis, five types of decisions were identified; assessment, intervention, organisation, communication and education. In addition to these documented decisions, three factors that influenced decision complexity were identified from a thematic analysis of the transcribed interviews; communication, patient related and properties of the decision. Nurses reported that communication decisions were the most difficult to make. However, the concept of nurses knowing the patient reduced the level of decision complexity. It is suggested that this has important implications for decision making practices of nurses working in the area of critical care and potentially for patient outcomes.

Students perceptions of learning outcomes from group-based, problem-based teaching and learning activities

Objective: A study aimed at exploring the variation in perceptions of learning outcomes reported by undergraduate nursing students enrolled in a problem-based learning subject in a pre-registration Bachelor of Nursing course (BN).
Method: Students were asked to respond to four open-ended questions which focussed on their learning outcomes in the different teaching/learning modalities of the subject. Data were analysed in two phases using a modified phenomenographic analysis. In the first phase a set of categories of description were developed from the student responses to questions related to the learning modalities. In the second phase the individual responses were classified in terms of the categories. Finally, correlations between the learning modalities were identified. In this paper the approach to analysis, the process of category identification and the correlations between the learning modalities will be described and the implications for further research and teaching will be discussed.
Results: The findings indicated that there were two distinct groups of student responses. Inward focussed students who described outcomes in terms of their own learning and students whose focus was outward i.e. describing learning in terms of patient care and how learning relates to that care. Another important result shows the relationship between the learning modalities and outcomes. From the students' perspective, the most sophisticated outcomes of the lectures and laboratories were ideas and skills to be used and applied in clinical settings. Whereas, the group-based activities in which clinical problems were presented to the students in the form of Situation Improvement Packages (SIPS) focussed their attention on the clinical setting which constituted a preparation for the realities of clinical practice.
Conclusion: The findings from this study indicate that students perceive their learning in the group based teaching/learning modality (SIPS) as effective in focussing them on the reality of their role in the clinical practice environment while lectures and laboratories provided the skills and knowledge required for this setting.

Deformation behavior of nanostructured aluminum alloy processed by severe plastic deformation

Microstructure and deformation behavior of the commercial aluminum-based Al7.5%Zn–2.7%Mg–2.3%Cu–0.15%Zr alloy subjected to high pressure torsion (HPT) were studied in the present work. A small grain size less than 100 nm, high level of internal stresses and presence of second phase nanoparticles were revealed by transmission electron microscopy (TEM) and X-ray diffraction (XRD). The nanostructured alloy processed by HPT exhibits tensile strength of 800 MPa and ductility of 20% at optimal temperature-strain rate conditions. Unusual influence of a short pre-annealing on tensile strength and ductility of as-processed alloy is discussed.