Biomimetic coating on pure titanium submitted to different surface treatments

Titanium (Ti) plates were firstly treated to form various types of oxide layers on the surface and then immersed into simulated body fluid (SBF) to evaluate the apatite forming ability. The surface morphology and roughness of the different oxide layers were measured by atomic force microscopy (AFM), and the surface energies were determined based on the Owens-Wendt (OW) methods. It was found that Ti samples after Alkali-Heat treatment (AH) achieved the best apatite formation after soaking in SBF for 3 weeks, compared to those without treatment, thermal or H₂O₂ oxidation. Furthermore, contact angle measurement revealed that the oxide layer on the alkali-heat treated Ti samples possessed the highest surface energy. The results indicate that the apatite inducing ability of a titanium oxide layer is linked to its surface energy. Apatite nucleation is easier on a surface with a higher surface energy.

Double-layer and hydration forces measured between silica sheets subjected to various surface treatments

Force measurements between silica surfaces in aqueous solutions of NaCl are reported. Silica is prepared with one of three surface treatments: (i) flaming, (ii) exposure to steam for 150 h, and (iii) brief exposure to ammonia vapor. Analysis of electrical double-layer interactions indicates that the surface density of silanol groups increases with steam treatment, and that exposure to ammonia etches the surface slightly and renders it porous. The force at short range is dominated by a strong repulsion which is attributed to hydration of the surface. The hydration component of the force is not significantly affected by the surface treatments, nor by electrolyte concentration over the range investigated (up to 0.1 M).

Flexural characteristics of coir fiber reinforced cementitious composites

This study has examined the flexural properties of natural and chemically modified coir fiber reinforced cementitious composites (CFRCC). Coir fibers of two different average lengths were used, and the longer coir fibers were also treated with a 1 % NaOH solution for comparison. The fibers were combined with cementitious materials and chemical agents (dispersant, defoamer or wetting agent) to form CFRCC. The flexural properties of the composites, including elastic stress, flexural strength, toughness and toughness index, were measured. The effects of fiber treatments, addition of chemical agents and accelerated ageing of composites on the composites’ flexural properties were examined. The results showed that the CFRCC samples were 5–12 % lighter than the conventional mortar, and that the addition of coir fibers improved the flexural strength of the CFRCC materials. Toughness and toughness index, which were associated with the work of fracture, were increased more than ten times. For the alkalized long coir fiber composites, a higher immediate and long-term toughness index was achieved. SEM microstructure images revealed improved physicochemical bonding in the treated CFRCC.

An electrochemical impedance study of ionic liquid film formation and aqueous corrosion of magnesium alloy ZE41

Ionic liquid surface treatments are proposed as a method of controlling corrosion processes on magnesium alloys. An important magnesium alloy, ZE41 (nominally 4% Zn and 1% rare earth), was treated with the ionic liquid trihexyl(tetradecyl)phosphonium diphenylphosphate (P₆₆₆₁₄DPP). Impedance spectra were acquired at intervals during the treatment, indicating the development of a film and allowing a measure of the film formation process to be obtained over time. Mechanically polished and electro-polished surfaces were prepared; these surfaces, treated and untreated, were subsequently exposed to 0.1 M NaCl aqueous solutions. The corrosion behavior of the prepared surfaces were assessed using impedance spectroscopy and optical microscopy. The results indicated a significant role for the method of surface preparation used and, in both cases, the ionic liquid treatment produced a more corrosion-resistant surface.

Oil-spill cleanup: the influence of acetylated curaua fibers on the oil-removal capability of magnetic composites

A magnetic resin based on cardanol, furfural, and curaua fibers was prepared and characterized. The material could be used in oil-spill cleanup processes, because of its aromatic/aliphatic balance. The resin was prepared through bulk polycondensation of cardanol and furfural in the presence of curaua fibers and maghemite nanoparticles. Hydrophobicity of the curaua fibers was improved by acetylation, increasing the oil-absorbing capability of the composites. The obtained magnetic composites were studied by Fourier-transform infrared spectroscopy, X-ray diffraction, and thermogravimetric analysis. Degree of cure, magnetic force, and oil-removal capability tests were also performed. The results show that the composites possess an elevated cure degree in addition to a considerable magnetic force. The materials exhibit a good oil removal capability in the presence of a magnetic field, which is improved by the use of acetylated curaua. In the best case, the composite filled with maghemite and curaua can remove 12 parts of oil from water.

Galling reduction through die surface treatment - testing three treatments for sheet metal stamping

This brief article describes how tool galling occurs in stamping and describes results of tests on how TiCN, Hard-Cr, and CrCN were used on sample parts to help reduce galling.

Exploring molecular changes at the surface of polypropylene after accelerated thermomolecular adhesion treatments

A central composite rotatable design (CCRD) method was used to investigate the performance of the accelerated thermomolecular adhesion process (ATmaP), at different operating conditions. ATmaP is a modified flame-treatment process that features the injection of a coupling agent into the flame to impart a tailored molecular surface chemistry on the work piece. In this study, the surface properties of treated polypropylene were evaluated using X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). All samples showed a significant increase in the relative concentration of oxygen (up to 12.2%) and nitrogen (up to 2.4%) at the surface in comparison with the untreated sample (0.7% oxygen and no detectable nitrogen) as measured by XPS. ToF-SIMS and principal components analysis (PCA) showed that ATmaP induced multiple reactions at the polypropylene surface such as chain scission, oxidation, nitration, condensation, and molecular loss, as indicated by changes in the relative intensities of the hydrocarbon (C₃H₇⁺ , C₃H₅⁺ , C₄H₇⁺, and C₅H₉⁺), nitrogen and oxygen-containing secondary ions (C₂H₃O⁺, C₃H₈N⁺, C₂H₅NO⁺, C₃H₆NO⁺, and C₃H₇NO⁺). The increase in relative intensity of the nitrogen oxide ions (C₂H₅NO⁺ and C₃H₇NO⁺) correlates with the process of incorporating oxides of nitrogen into the surface as a result of the injection of the ATmaP coupling agent.

Achieving a chromium rich surface upon steels via FBR-CVD chromising treatments

Surface alloying via fluidised bed reactor (FBR) chemical vapour deposition (CVD) can be used to produce adherent and highly corrosion resistant surface layers. In this work, 304, 316, and 409 stainless steels and 1020 steel were chromised, producing distinct surface layers tens of micrometres thick. The composition and surface of these layers was characterised using microscopy, GDOES, and XPS. Surfaces were highly enriched in Cr and displayed improved corrosion resistance as determined by electrochemical evaluations. This work demonstrates that it is possible to form continuous, functional and corrosion resistant Cr-rich surface layers via FBR-CVD on a variety of steels.

Electrostatically confined plasma in segmented hollow cathode geometries for surface engineering

A segmented hollow cathode (SHC) geometry was used for electrostatic confinement of plasma, and surface engineering treatments were conducted in this arrangement. The assessed processes included plasma nitriding, reactive deposition of sputtered material, and deposition of carbonaceous films by plasma-enhanced chemical vapor deposition with a bipolar pulsed-dc power supply on steel substrates. The treated specimens exhibited uniform surface morphology and deposition layers. Characterization techniques included optical microscopy, scanning electron microscopy with energy dispersive X-ray capability, and X-ray diffraction. The advantages and potential applications of the SHC arrangement are discussed in view of these results.

Mitigation of N₂O emissions from surface-irrigated cropping systems using water management and the nitrification inhibitor DMPP

Soils under irrigated agriculture are a significant source of nitrous oxide (N2O) owing to high inputs of nitrogen (N) fertiliser and water. This study investigated the potential for N2O mitigation by manipulating the soil moisture deficit through irrigation scheduling in combination with, and in comparison to, using the nitrification inhibitor, 3,4-dimethylpyrazole phosphate (DMPP). Lysimeter cores planted with wheat were fitted with automated chambers for continuous measurements of N2O fluxes. Treatments included conventional irrigation (CONV), reduced deficit irrigation (RED), CONV-DMPP and RED-DMPP. The total seasonal volume of irrigation water applied was constant for all treatments but the timing and quantity in individual irrigation applications varied among treatments. 15N-labelled urea was used to track the source of N2O emissions and plant N uptake. The majority of N2O emissions occurred immediately after irrigations began on 1 September 2014. Applying RED and DMPP individually slightly decreased N2O emissions but when applied in combination (RED-DMPP) the greatest reductions in N2O emissions were observed. There was no effect of treatments on plant N uptake, 15N recovery or yield possibly because the system was not N limited. Half of the plant N and 53% to 87% of N2O was derived from non-fertiliser sources in soil, highlighting the opportunity to further exploit this valuable N pool.