Highly crumpled boron nitride nanosheets as adsorbents: scalable solvent-less production

Boron nitride nanosheets (BNNSs), so-called “white graphene”, have recently received increasing attention, both theoretically and experimentally. Although many synthetic procedures have been proposed for the synthesis of BNNSs, finding a simple, solvent-less, catalyst-free, and large-scale production route is still a challenge. Here, a facile, solvent-less, low cost, and high yield process is developed, in which mechanical solid-state exfoliation allows scalable production of crumple BNNSs from commercial BN powders with a high surface area. Importantly, these BNNSs show unprecedentedly high adsorption of proteins described by various adsorption isotherms and kinetics models. In addition, the saturated BNNSs exhibit excellent recyclability, and maintain a high sorption capacity even after five cycles through simply regeneration process of heating in air. This easy recyclability route further demonstrates the great potential of BNNSs for water cleaning application.

Fibroblast growth factor-2 over-rides insulin-like growth factor-I induced proliferation and cell survival in human neuroblastoma cells

The insulin-like growth factor (IGF) system is a key regulator of cell growth, survival and differentiation, and these functions are co-modulated by other growth factors including fibroblast growth factor-2 (FGF-2). To investigate IGF/FGF interactions in neuronal cells, we employed neuroblastoma cells (SK-N-MC). In serum free conditions proliferation of the SK-N-MC cells was promoted by IGF-I (25 ng/ml), but blunted by FGF-2 (50 ng/ml). IGF-I-induced proliferation was abolished in the presence of FGF-2 even when IGF-I was used at 100 ng/ml. In addition to our previously described FGF-2 induced proteolytic cleavage of IGFBP-2, we found that FGF-2 increased IGFBP-6 levels in conditioned medium (CM) without affecting IGFBP-6 mRNA abundance. Modulation of IGFBP-2 and -6 levels were not significant mechanisms involved in the blockade of IGF-I action since the potent IGF-I analogues [QAYL]IGF-I and des(1-3)IGF-I (minimal IGFBP affinity) were unable to overcome FGF-2 inhibition of cell proliferation. FGF-2 treated cells showed morphological differentiation expressing the TUJ1 neuronal marker while cells treated with IGF-I alone showed no morphological change. When IGF-I was combined with FGF-2, however, cell morphology was indistinguishable from that seen with FGF-2 alone. FGF-2 inhibited proliferation and enhanced differentiation was also associated with a 70% increase in cell death. Although IGF-I alone was potently anti-apoptotic (60% decreased), IGF-I was unable to prevent apoptosis when administrated in combination with FGF-2. Gene-array analysis confirmed FGF-2 activation of the intrinsic and extrinsic apoptotic pathways and blockade of IGF anti-apoptotic signaling. FGF-2, directly and indirectly, overcomes the proliferative and anti-apoptotic activity of IGF-I by complex mechanisms, including enhancement of differentiation and apoptotic pathways, and inhibition of IGF-I induced anti-apoptotic signalling. Modulation of IGF binding protein abundance by FGF-2 does not play a significant role in inhibition of IGF-I induced mitogenesis.

Lithium ion mobility in poly(vinyl alcohol) based polymer electrolytes as determined by 7Li NMR spectroscopy

Solvent-free polymer electrolytes based on poly(vinyl alcohol) (PVA) and LiCF₃SO₃ have shown relatively high conductivities (10⁻⁸-10⁻⁴ S cm⁻¹), with Arrhenius temperature dependence below the differential scanning calorimeter (DSC) glass transition temperature (343 K). This behaviour is in stark contrast to traditional polymer electrolytes in which the conductivity reflects VTF behaviour. ⁷Li nuclear magnetic resonance (NMR) spectroscopy has been employed to develop a better understanding of the conduction mechanism. Variable temperature NMR has indicated that, unlike traditional polymer electrolytes where the linewidth reaches a rigid lattice limit near T_g, the lithium linewidths show an exponential decrease with increasing temperature between 260 and 360 K. The rigid lattice limit appears to be below 260 K. Consequently, the mechanism for ion conduction appears to be decoupled from the main segmental motions of the PVA. Possible mechanisms include ion hopping, proton conduction or ionic motion assisted by secondary polymer relaxations.

Ion conductivity in amorphous polymer/salt mixtures

Amorphous polymer/salt mixtures based on polyvinyl alcohol and poly(hydroxyethylacrylate) and poly(hydroxyethylmethacrylate) are described. The polyvinylalcohol materials have been prepared by a solvent free hot pressing technique as well as the traditional solvent casting method. The hot pressing technique allows the production of samples which are genuinely free of solvents and thereby has allowed an assessment in this work of the effect of residual solvent on conductivity. The acrylate materials were prepared by direct polymerization of monomer/salt mixtures, thus avoiding the need for solvents. These materials have glass transitions around or well above room temperature, but nonetheless have conductivities as high as 10⁻⁷ S/cm at room temperature. The temperature and composition dependence of conductivity are also presented.

Cryo-electron microscopy and single molecule fluorescent microscopy detect CD4 receptor induced HIV size expansion prior to cell entry

Viruses are often thought to have static structure, and they only remodel after the viruses have entered target cells. Here, we detected a size expansion of virus particles prior to viral entry using cryo-electron microscopy (cryo-EM) and single molecule fluorescence imaging. HIV expanded both under cell-free conditions with soluble receptor CD4 (sCD4) targeting the CD4 binding site on the HIV-1 envelope protein (Env) and when HIV binds to receptor on cellular membrane. We have shown that the HIV Env is needed to facilitate receptor induced virus size expansions, showing that the 'lynchpin' for size expansion is highly specific. We demonstrate that the size expansion required maturation of HIV and an internal capsid core with wild type stability, suggesting that different HIV compartments are linked and are involved in remodelling. Our work reveals a previously unknown event in HIV entry, and we propose that this pre-entry priming process enables HIV particles to facilitate the subsequent steps in infection.

Enhancement of ‘dry’ proton conductivity by self-assembled nanochannels in all-solid polyelectrolytes

Proton transport has been recognized as an essential process in many biological systems, as well as electrochemical devices including fuel cells and redox flow batteries. In the present study, we address the pressing need for solvent-free proton conducting polymer electrolytes for high-temperature PEM fuel cell applications by developing a novel all-solid polyelectrolyte membrane with a self-assembled proton-channel structure. We show that this self-assembled nanostructure endows the material with exciting ‘dry’ proton conductivity at elevated temperatures, as high as 0.3 mS cm−1 at 120 °C, making it an attractive candidate for high-temperature PEM fuel cell applications. Based on the combined investigation of solid-state NMR, FTIR and conductivity measurements, we propose that both molecular design and nano-scale structures are essential for obtaining highly conductive anhydrous proton conductors.

Sexual conflict and polyspermy under sperm-limited conditions : in situ evidence from field simulations with the free-spawning marine echinoid Evechinus chloroticus

For free‐spawning organisms that release gametes into the sea, sperm limitation (too few sperm to fertilize all eggs) is a major factor limiting reproductive success. Given such circumstances, the presence of several mechanisms to prevent polyspermy (too many sperm) may seem paradoxical; however, a growing body of data suggests that natural fertilization levels, though variable, can routinely be high. Under such conditions, polyspermy is much more likely. The tension between sperm limitation and polyspermy represents sexual conflict because males, in competing to fertilize as many eggs as possible, can impose lethal costs on eggs if multiple sperm gain entry. Here we present data for a marine invertebrate indicating high levels of polyspermy under sperm‐limited conditions. When the sea urchin Evechinus chloroticus was induced to spawn in situ, mean rates of polyspermy were 17.3% ±3.4%, and polyspermy was recorded at rates as high as 62.7%. Polyspermy was nearly always present, even when fertilization rates were <50%, confirming predictions that it should be present under sperm‐limited conditions. Both sperm limitation and polyspermy imposed substantial reproductive costs, and we conclude that both sexual conflict related to polyspermy and sperm limitation have been simultaneous strong selective forces shaping the evolution of reproductive traits in the sea.

Influence of processing conditions on polymorphic behavior, crystallinity, and morphology of electrospun poly(VInylidene fluoride) nanofibers

The polymorphism and crystallinity of poly(vinylidene fluoride) (PVDF) membranes, made from electrospinning of the PVDF in pure N,N-dimethylformamide (DMF) and DMF/acetone mixture solutions are studied. Influence of the processing and solution parameters such as flow rate, applied voltage, solvent system, and mixture ratio, on nanofiber morphology, total crystallinity, and crystal phase content of the nanofibers are investigated using scanning electron microscopy, wide-angle X-ray scattering, differential scanning calorimetric, and Fourier transform infrared spectroscopy. The results show that solutions of 20% w/w PVDF in two solvent systems of DMF and DMF/acetone (with volume ratios of 3/1 and 1/1) are electrospinnable; however, using DMF/acetone volume ratio of 1/3 led to blockage of the needle and spinning process was stopped. Very high fraction of β-phase (∼79%-85%) was obtained for investigated nanofiber, while degree of crystallinity increased to 59% which is quite high due to the strong influence of electrospinning on ordering the microstructure. Interestingly, ultrafine fibers with the diameter of 12 and 15 nm were obtained in this work. Uniform and bead free nanofiber was formed when a certain amount of acetone was added in to the electrospinning solution.

Single enatiomer free-radical chemistry - Lewis acid-mediated reductions of racemic halides using chiral non-racemic stannanes

Additions of one to two equivalents of Lewis acids that include magnesium salts to free-radical reduction reactions involving ester functionalized radicals and (1R,2S,5R)-menthyldiphenyltin hydride 4, bis((1R,2S,5R)-menthyl)phenyltin hydride 5, tris((1R,2S,5R)-menthyl)tin hydride 6, bis((1R,2S,5R)-menthyl)-[8-(N,N-dimethylamino)naphthyl]tin hydride 12, bis((1R,2S,5R)-menthyl)-[1-((S)-N,N-dimethylaminoethyl)phenyl]tin hydride 13 or 3α-dimethylstannyl-5α-cholestane 14 result in remarkable enantioselectivities. Examples include (S)-naproxen ethyl ester 16, produced in 74% yield and greater than 99% ee at −78°C from the bromide and 5 in the presence of MgBr₂, and ethyl (R)-N-trifluoroacetyl-_D-phenylglycinate 18, obtained in 78% yield and 99% ee under identical conditions. Kinetic and computational studies provide insight into the origins of these observations.

Static and metadynamic recrystallization of interstitial free steels during hot deformation

A rapid method was used to identify kinetics of the recrystallization for two IF (Interstitial Free) steels which have different phosphorous and boron contents. The static and metadynamic softening behaviour of the materials for a range of strain rates and temperatures were quantified. The critical strain for initiation of strain independent softening was estimated for the IF steels in respect to the time for 50 percent softening after deformation. The results showed that the strain for the initiation of strain independent softening (often referred to as metadynamic recrystallization) varies with the Zener Hollomon parameter. Classic static recrystallization was observed at strains below the strain independent softening for all processing conditions and the strain rate had a strong effect on the time for strain independent softening. Results also revealed that static and metadynamic recrystallization was delayed owing to the phosphorous and boron alloying elements. Hence, the large strain at above no-recrystallization temperature may be required for the early stage of Finishing Stands Unit (FSU) in hot strip rolling mills to initiate austenite grain refinement of phosphorous and boron added IF steels.

Dielectric characterization of conducting textiles using free space transmission measurements: accuracy and methods for improvement

The dielectric behaviour of in-situ polymerized thin polypyrrole (PPy) films on synthetic textile substrates were obtained in the 1–18 GHz region using free space transmission and reflection methods. The PPy/para-toluene-2-sulphonic acid (pTSA) coated fabrics exhibited an absorption dominated total shielding effectiveness (SE) of up to −7.34 dB, which corresponds to more than 80% of incident radiation. The permittivity response is significantly influenced by the changes in ambient conditions, sample size and diffraction around the sample. Mathematical diffraction removal, time-gating tools and high gain horns were utilized to improve the permittivity response. A narrow time-gate of 0.15 ns produced accurate response for frequencies above 6.7 GHz and the high gain horns further improved the response in the 7.5–18 GHz range. Errors between calculated and measured values of reflection were most commonly within 2%, indicating good accuracy of the method.

Diacetone alcohol, a dispersant solvent, contributes to acute toxicity of a fipronil-based insecticide in a passerine bird

Fipronil, a phenyl pyrazole pesticide, is aerially applied in eastern Australia to control locust outbreaks, usually as “Adonis 3UL Insecticide^®” (BASF), an ultra low (UL) volume formulation containing 0.3% active pesticide. We tested the toxicities of technical-grade fipronil, the Adonis 3UL formulation and its components in zebra finch, a native bird at risk of exposure in locust control regions. We estimated oral-dose LD50 by the Up-and-Down method. Under laboratory conditions, we identified unexpectedly high toxicities due exclusively to diacetone alcohol (DAA), a solvent making up 12.5% of the Adonis 3UL formulation. In contrast, finches were asymptomatic when exposed to 0.3% technical grade fipronil dissolved in a minimum amount of acetone. Depending upon the behaviour and persistence of DAA under field conditions, this formulation of Adonis 3UL may pose a far greater threat to the health of small birds and possibly other vertebrates than expected for fipronil alone.

Thermodynamics of lipophilic drug binding to intestinal fatty acid binding protein and permeation across membranes

Intestinal fatty acid binding protein (I-FABP) is present at high levels in the absorptive cells of the intestine (enterocytes), where it plays a role in the intracellular solubilization of fatty acids (FA). However, I-FABP has also been shown to bind to a range of non-FA ligands, including some lipophilic drug molecules. Thus, in addition to its central role in FA trafficking, I-FABP potentially serves as an important intracellular carrier of lipophilic drugs. In this study we provide a detailed thermodynamic analysis of the binding and stability properties of I-FABP in complex with a series of fibrate and fenamate drugs to provide an insight into the forces driving drug binding to I-FABP. Drug binding and selectivity for I-FABP are driven by the interplay of protein−ligand interactions and solvent processes. The Gibbs free energies (ΔG°) determined from dissociation constants at 25 °C ranged from −6.2 to −10 kcal/mol. The reaction energetics indicate that drug binding to I-FABP is an enthalpy−entropy driven process. The relationship between I-FABP stability and drug binding affinity was examined by pulse proteolysis. There is a strong coupling between drug binding and I-FABP stability. The effect of an I-FABP protein sink on the kinetics and thermodynamics of tolfenamic acid permeation across an artificial phospholipid membrane were investigated. I-FABP significantly decreased the energy barrier for desorption of tolfenamic acid from the membrane into the acceptor compartment. Taken together, these data suggest that the formation of stable drug−I-FABP complexes is thermodynamically viable under conditions simulating the reactant concentrations likely observed in vivo and maybe a significant biochemical process that serves as a driving force for passive intestinal absorption of lipophilic drugs.