Effect of bulk microstructure of commercially pure titanium on surface characteristics and fatigue properties after surface modification by sand blasting and acid-etching

Surface modification techniques are widely used to enhance the biological response to the implant materials. These techniques generally create a roughened surface, effectively increasing the surface area thus promoting cell adhesion. However, a negative side effect is a higher susceptibility of a roughened surface to failure due to the presence of multiple stress concentrators. The purpose of the study reported here was to examine the effects of surface modification by sand blasting and acid-etching (SLA) on the microstructure and fatigue performance of coarse-grained and ultrafine-grained (UFG) commercially pure titanium. Finer grain sizes, produced by equal channel angular pressing, resulted in lower values of surface roughness in SLA-processed material. This effect was associated with greater resistance of the UFG structure to plastic deformation. The fatigue properties of UFG Ti were found to be superior to those of coarse-grained Ti and conventional Ti-6Al-4V, both before and after SLA-treatment.

Microstructure and mechanical properties of Ti-15Zr alloy used as dental implant material

Ti-Zr alloys have recently started to receive a considerable amount of attention as promising materials for dental applications. This work compares mechanical properties of a new Ti-15Zr alloy to those of commercially pure titanium Grade4 in two surface conditions - machined and modified by sand-blasting and etching (SLA). As a result of significantly smaller grain size in the initial condition (1-2µm), the strength of Ti-15Zr alloy was found to be 10-15% higher than that of Grade4 titanium without reduction in the tensile elongation or compromising the fracture toughness. The fatigue endurance limit of the alloy was increased by around 30% (560MPa vs. 435MPa and 500MPa vs. 380MPa for machined and SLA-treated surfaces, respectively). Additional implant fatigue tests showed enhanced fatigue performance of Ti-15Zr over Ti-Grade4.

Comparative study of ni effect on the corrosion behavior of low alloy steels in FGD and acid rain environments

The alloying effect of a small amount of nickel on low alloy steel for application to flue gas desulfurization(FGD) systems was studied. The structural characteristics of the rust layer were investigated by scanning electron microscopy(SEM). The electrochemical properties were examined by means of potentiostatic polarization test, potentiodynamic polarization test, and electrochemical impedance spectroscopy(EIS) in a modified green death solution of 16.9 vol.% H2SO4+0.35 vol.% HC1 at 60°C and an acid rain solution of 6.25 X 10-5 M H2S04+5.5 X 10-3 M NaCl at room temperature. It was found that as the amount of nickel increased, the corrosion rate increased in the modified green death solution, which seemed to result from micro-galvanic corrosion between NiS and alloy matrix. In acid rain solution, the corrosion rate decreased as the amount of nickel increased due to the repulsive force of NiFe204 rust against Cl-ions by electronegativity.

The facet selectivity of inorganic ions on silver nanocrystals in etching reactions

The facet selectivity of the halide ions and chlorauric acid for several shaped silver nanocrystals is presented in this paper. Two inorganic ions show different representations when they are used for etching silver nanocrystals in the self-sacrificial template reaction. The morphological changes of the silver nanocrystals indicate that the halide ions prefer to etch the (110) facets of silver nanocrystals, while in the chlorauric acid etching reaction, gold first modifies the (110) facets and then lets chlorauric acid etch the (111) facets instead. The selective facet etching on individual nanoparticles in the solution phase has crucial significance in the control-synthesis of nanocrystals and the facet asymmetric reaction.

Electrochemical etching of aluminium alloy in ionic liquids

AA5083 aluminium alloy has been shown to be partially passivated by a 2-step anodic pre-treatment in Trihexyl(tetradecyl)phosphonium bis(trifluoromethylsulfonyl)amide ([P6,6,6,14][NTf2]) ionic liquid. Surface characterisation revealed that an electrochemical etching process had occurred, comparable to acid etching of aluminium. Scanning electron microscopy/energy dispersive x-ray spectroscopy results have established that magnesium dealloyed from the Mg2Si intermetallic particles and metal fluorides were deposited onto the remaining Mg2Si sites, which subsequently led to decreased anodic corrosion kinetics (to one third of the control) as well as an increase in the corrosion and pitting potentials. This unique electrochemical etching process offers a simple and quick method to improve the corrosion resistance of an aluminium alloy as it leads to a more uniform surface, in terms of defect size and distribution, compared to conventional acid etching. This process has the potential to be used as a pre-treatment to inhibit corrosion of AA5083 alloy.

Sulfur-doped porous reduced graphene oxide hollow nanosphere frameworks as metal-free electrocatalysts for oxygen reduction reaction and as supercapacitor electrode materials.

Chemical doping with foreign atoms is an effective approach to significantly enhance the electrochemical performance of the carbon materials. Herein, sulfur-doped three-dimensional (3D) porous reduced graphene oxide (RGO) hollow nanosphere frameworks (S-PGHS) are fabricated by directly annealing graphene oxide (GO)-encapsulated amino-modified SiO2 nanoparticles with dibenzyl disulfide (DBDS), followed by hydrofluoric acid etching. The XPS and Raman spectra confirmed that sulfur atoms were successfully introduced into the PGHS framework via covalent bonds. The as-prepared S-PGHS has been demonstrated to be an efficient metal-free electrocatalyst for oxygen reduction reaction (ORR) with the activity comparable to that of commercial Pt/C (40%) and much better methanol tolerance and durability, and to be a supercapacitor electrode material with a high specific capacitance of 343 F g(-1), good rate capability and excellent cycling stability in aqueous electrolytes. The impressive performance for ORR and supercapacitors is believed to be due to the synergistic effect caused by sulfur-doping enhancing the electrochemical activity and 3D porous hollow nanosphere framework structures facilitating ion diffusion and electronic transfer.

Wettability investigation of UV/oand acid functionalized MWCNT and MWCNT/PMMA nanocomposites by contact angle measurement

The dispersion state of individual MWCNT in the polymer matrix influences the mechanical, thermal, and electrical properties of the resulting composite. One method of obtaining a good dispersion state of MWCNT in a polymer matrix is to functionalize the surface of MWCNT using various treatments to enhance the surface energy and increase the dispersibility of MWCNT. In this study, wettability and surface energy of UV/Oand acid-treated multiwall carbon nanotubes (MWCNTs) and its polymethyl methacrylate (PMMA) polymer nanocomposites were measured using contact angle analysis in various solvent media. Contact angle analysis was based on ethylene glycol-water-glycerol probe liquid set and data was further fitted into geometric mean (Fowkes), van Oss-Chaudhury-Good (GvOC), and Chang-Qing-Chen (CQC) models to determine both nonpolar and acid base surface energy components. Analysis was conducted on MWCNT thin films subjected to different levels of UV/Oand acid treatments as well as their resulting MWCNT/PMMA nanocomposites. Contact angle analysis of thin films and nanocomposites revealed that the total surface energy of all samples was well fitted with each other. In addition, CQC model was able to determine the surface nature and polarity of MWCNT and its nanocomposites. Results indicated that the wettability changes in the thin film and its nanocomposites are due to the change in surface chemistry. Finally, electrical properties of nanocomposites were measured to investigate the effect of surface functionality (acid or basic) on the MWCNT surfaces.

The mitochondrial rhomboid protease PSARL is a new candidate gene for type 2 diabetes

Aims/hypothesis This study aimed to identify genes that are expressed in skeletal muscle, encode proteins with functional significance in mitochondria, and are associated with type 2 diabetes.
Methods We screened for differentially expressed genes in skeletal muscle of Psammomys obesus (Israeli sand rats), and prioritised these on the basis of genomic localisation and bioinformatics analysis for proteins with likely mitochondrial functions.
Results We identified a mitochondrial intramembrane protease, known as presenilins-associated rhomboid-like protein (PSARL) that is associated with insulin resistance and type 2 diabetes. Expression of PSARL was reduced in skeletal muscle of diabetic Psammomys obesus, and restored after exercise training to successfully treat the diabetes. PSARL gene expression in human skeletal muscle was correlated with insulin sensitivity as assessed by glucose disposal during a hyperinsulinaemic–euglycaemic clamp. In 1,031 human subjects, an amino acid substitution (Leu262Val) in PSARL was associated with increased plasma insulin concentration, a key risk factor for diabetes. Furthermore, this variant interacted strongly with age to affect insulin levels, accounting for 5% of the variation in plasma insulin in elderly subjects.
Conclusions/interpretation Variation in PSARL sequence and/or expression may be an important new risk factor for type 2 diabetes and other components of the metabolic syndrome.

Microscopic nature and elemental composition of brown coal fly ash particles from a large coal fired power station

In this study, Australian brown coal fly ash particles have been collected from power station and analysed by scanning electron microscopy to obtain morphological information and elemental composition of individual particles. The most common particles found to be the irregular shape particle aggregates. Other shapes include ball shape with smooth surface and with some attachments; and crystal shape fine particles. The X-ray spectra of each fly ash particle revealed five groups of elemental composition, they are Si-rich particles; Ca-rich particles; Fe-rich particles; particles with Mg-Ca Matrix and particles with Si-Ca matrix. A particle sire distribution analysis has been conducted using particle size analyser and found to have a mean particle size of 21fim. The sample then was separated into fine and coarse fractions using aerodynamic classifier, and the elemental composition of both fractions were determined by ICP-AES. Borate fusion and acid dissolution method was used for sample preparation. It is found that some environmental sensitive elements such as Zn, Pb, Ni, K and Cu are enriched in fine fly ash particles. Ca has much higher contents in fine particles as well. Si and Mg have higher concentrations in coarse particles.

An in vivo cytotoxicity threshold for influenza A virus-specific effector and memory CD8+ T cells

Influenza A virus infection of C57BL/6 (B6) mice is characterized by prominent CD8 T cell responses to H2Db complexed with peptides from the viral nucleoprotein (NP366, ASNENMETM) and acid polymerase (PA224, SSLENFRAYV). An in vivo cytotoxicity assay that depends on the adoptive transfer of peptide-pulsed, syngeneic targets was used in this study to quantitate the cytotoxic potential of DbNP366- and DbPA224-specific acute and memory CD8 T cells following primary or secondary virus challenge. Both T cell populations displayed equivalent levels of in vivo effector function when comparable numbers were transferred into naive B6 hosts. Cytotoxic activity following primary infection clearly correlated with the frequency of tetramer-stained CD8 T cells. This relationship looked, however, to be less direct following secondary exposure, partly because the numbers of CD8DbNP366 T cells were greatly in excess. However, calculating the in vivo E:T ratios indicated that in vivo lysis, like many other biological functions, is threshold dependent. Furthermore, the capacity to eliminate peptide-pulsed targets was independent of the differentiation state (i.e., primary or secondary effectors) and was comparable for the two T cell specificities that were analyzed. These experiments provide insights that may be of value for adoptive immunotherapy, where careful consideration of both the activation state and the number of effector cells is required.

Protection and compensation in the influenza virus-specific CD8+ T cell response.

Influenza virus-specific CD8+ T cells generally recognize peptides derived from conserved, internal proteins that are not subject to antibody-mediated selection pressure. Prior exposure to any one influenza A virus (H1N1) can prime for a secondary CD8+ T cell response to a serologically different influenza A virus (H3N2). The protection afforded by this recall of established CD8+ T cell memory, although limited, is not negligible. Key characteristics of primary and secondary influenza-specific host responses are probed here with recombinant viruses expressing modified nucleoprotein (NP) and acid polymerase (PA) genes. Point mutations were introduced into the epitopes derived from the NP and PA such that they no longer bound the presenting H2Db MHC class I glycoprotein, and reassortant H1N1 and H3N2 viruses were made by reverse genetics. Conventional (C57BL/6J, H2b, and Ig+/+) and Ig-/- (muMT) mice were more susceptible to challenge with the single NP [HKx31 influenza A virus (HK)-NP] and PA (HK-PA) mutants, but unlike the Ig-/- mice, Ig+/+ mice were surprisingly resistant to the HK-NP/-PA double mutant. This virus was found to promote an enhanced IgG response resulting, perhaps, from the delayed elimination of antigen-presenting cells. Antigen persistence also could explain the increase in size of the minor KbPB1703 CD8+ T cell population in mice infected with the mutant viruses. The extent of such compensation was always partial, giving the impression that any virus-specific CD8+ T cell response operates within constrained limits. It seems that the relationship between protective humoral and cellular immunity is neither simple nor readily predicted.

Alkalosis increases muscle K+ release, but lowers plasma [K+] and delays fatigue during dynamic forearm exercise

Alkalosis enhances human exercise performance, and reduces K⁺ loss in contracting rat muscle. We investigated alkalosis effects on K⁺ regulation, ionic regulation and fatigue during intense exercise in nine untrained volunteers. Concentric finger flexions were conducted at 75% peak work rate (-3 W) until fatigue, under alkalosis (Alk, NaHCO₃, 0.3 g kg⁻¹) and control (Con, CaCO₃) conditions, 1 month apart in a randomised, double-blind, crossover design. Deep antecubital venous (v) and radial arterial (a) blood was drawn at rest, during exercise and recovery, to determine arterio-venous differences for electrolytes, fluid shifts, acid–base and gas exchange. Finger flexion exercise barely perturbed arterial plasma ions and acid–base status, but induced marked arterio-venous changes. Alk elevated [HCO₃⁻] and P^CO2, and lowered [H+] (P < 0.05). Time to fatigue increased substantially during Alk (25 ± 8%, P < 0.05), whilst both [K⁺]_a and [K⁺]_v were reduced (P < 0.01) and [K⁺]_a-v during exercise tended to be greater (P= 0.056, n= 8). Muscle K⁺ efflux at fatigue was greater in Alk (21.2 ± 7.6 µmol min⁻¹, 32 ± 7%, P < 0.05, n= 6), but peak K⁺ uptake rate was elevated during recovery (15 ± 7%, P < 0.05) suggesting increased muscle Na⁺,K^+-ATPase activity. Alk induced greater [Na⁺]_a, [Cl⁻]_v, muscle Cl⁻ influx and muscle lactate concentration ([Lac⁻]) efflux during exercise and recovery (P < 0.05). The lower circulating [K⁺] and greater muscle K⁺ uptake, Na⁺ delivery and Cl⁻ uptake with Alk, are all consistent with preservation of membrane excitability during exercise. This suggests that lesser exercise-induced membrane depolarization may be an important mechanism underlying enhanced exercise performance with Alk. Thus Alk was associated with improved regulation of K⁺, Na⁺, Cl⁻ and Lac⁻.

Influence of atmospheric helium plasma on the surface energy of jute fibres and the performance of resulting composites

In this work, an atmospheric pressure glow discharge helium plasma treatment was employed to modify the surface properties of jute fibres. The resulting bio-composites showed an increase in flexural properties and interlaminar shear strength (ILSS) compared to composites produced using untreated jute fibres. To understand the reason behind the ILSS improvement, the acid–base properties of jute fibres were determined by contact angle analysis using the capillary rise method. The results were fitted further to van Oss–Chaudhury–Good (vOCG) and Chang–Qin–Chen (CQC) models to determine the Lifshitz–van der Waals (LW) and acid–base components of surface energy. Surface energy determined by the vOCG model revealed that plasma treatment of jute fibre resulted in a 22% increase in total surface energy, a 19% increase in the LW component and a 24% increase in the acid–base component of surface energy. The increase in the acid–base component is due to the significant increase (69%) in the electron-accepting (γ+S) parameter. On the other hand, the CQC model clearly indicates an amphoteric nature of the fibre surface based on opposite signs of the acid and base principal values (PSa and PSb). Overall, the results indicated that increases in both LW and acid–base components were responsible for improvement in the properties of the composites.

Activity patterns of insectivorous bats and birds in northern Scandinavia (69° N), during continuous midsummer daylight

Previous studies suggest that many species of insectivorous bats are nocturnal, despite the relatively low availability of their insect prey at night, because of the risk of predation by diurnal predatory birds. We hypothesised that if this was the case bats living above the arctic circle would alter their feeding behaviour during midsummer because there would no longer be any benefit to restricting their activity to the period when their prey are least abundant. Alternatively, if bats were more influenced by competition from aerial insectivorous birds they would continue to feed at ‘night’ to avoid such competition. In northern Norway (69° N), during continuous midsummer daylight, insectivorous sand martins (Riparia riparia) concentrated their aerial feeding activity when aerial insects were most abundant. The birds stopped feeding between 23:00 and 07:00 when aerial insects were least abundant. In contrast, northern bats (Eptesicus nilssonii), fed mostly between 22:00 and 02:00, coinciding with the lowest aerial insect availability, and with the period when light levels were lowest (ca 1000 lux). Bat activity patterns were closest to those predicted by the avian competition hypothesis. The low densities of both sand martins and Northern bats in the study area, however, were less consistent with this hypothesis. Possibly populations of both species were higher historically and the observed patterns reflected historical competition. Bat activity was most closely correlated to ambient light levels. This raised two alternative explanations that we could not eliminate. Perhaps there was differential predation risk, between the brightest and darkest parts of the day, because the visual capacities of falcons are strongly dependent on luminance. Alternatively the bats may have been entrained to emerge at given light levels by their behaviour at other times of year.