Quantifying rubber degradation using NMR

Ageing can lead to the degradation of the tensile properties of natural rubber. The ageing process causes changes in the polymer segmental motion as well as the chemical structure, both of which can be monitored using nuclear magnetic resonance (NMR) spectroscopy. This work demonstrates that NMR can quantify rubber degradation due to ageing, and also that relatively simple NMR equipment can be used. This simpler equipment can be made portable and so could give a simple and fast indication of the condition of rubber in service. The 1H NMR transverse relaxation time, T2, and the 13C NMR spectrum using cross polarization and magic angle spinning (CP MAS) for samples taken at various levels of a degraded natural rubber liner were compared. These experiments showed that, as the level of degradation increased, the 1H NMR transverse relaxation time decreased. The 13C spectra showed considerable peak broadening, indicative of decreased mobility with increased level of degradation as well as the presence of degradation products. Further investigations using lower powered NMR equipment to measure the 1H NMR transverse relaxation times of two different series of natural rubbers were also performed. This work has shown that this simpler method is also sensitive to structural and mechanical property changes in the rubber. This method of monitoring rubber degradation could lead to the non-destructive use of NMR to determine the condition of a part in service.

Thermal degradation of natural rubber/ZNO nanocomposites

Nanoparticies have been widely used to enhance the properties of natural rubber (NR). In the present paper a novel nanocomposite was developed by blending nano-ZnO slurry with prevulcanized NR latex, and the thermal degradation process of pure NR and NR/ZnO nanocomposites with different nano-ZnO loading was studied with a Perkin Elemer TGA-7 thermogravimetric analyzer. The thermal degradation parameters of NR/ZnO (2 parts ZnO per hundred dlY rubber) at different heating rates (Bs) were studied. The results show that the thermal degradation of pure NR and NR/ZnO nanocomposites in nitrogen is a one-step reaction. The degradation temperatures of NR/ZnO nanocomposite increase with an increasing B. The peak height (R_p) on the differential thermogravimetric curve increases with the increase of B. The degradation rates are not affected significantly by B, and the average values of thermal degradation rate C_p and C_f are 44.42 % and 81.04 %, respectively. The thermal degradation kinetic parameters are calculated with Ozawa-Flynn-Wall method. The activation energy (E) and the frequency factor (A) vary with ecomposition degree, and can be divided into three phases corresponding to the volatilization of low-molecular-weight materials, the thermal degradation ofNR main chains and the decomposition of residual carbon.

Thermal degradation kinetics and morphology of natural rubber/silica nanocomposites

A novel natural rubber/silica (NR/SiO₂) nanocomposite with a SiO₂ loading of 4 wt% is developed by incorporating latex compounding with self-assembly techniques. The SiO₂ nanoparticles are homogenouslydistributed throughout the NR matrix as spherical nano-clusters with an average size of 75 nm. In comparison with the host NR, the thermal resistance of the nanocomposite is significantly improved. The degradation temperatures (T), reaction activation energy(E), and reaction order (n) of the nanocomposite are markedly higher than those of the pure NR, due to significant retardant effect of the SiO₂ nanoparticles.

Thermal degradation kinetics and mechanism of epoxidized natural rubber

Thermal resistance is one of the most dominative properties for polymer materials. Thermal degradation mechanisms of epoxidized natural rubber (ENR) and NR are studied by thermogravimetric analysis (TGA) and differential thermal analysis (DTA). The results show that, the introduction of epoxy groups into the NR molecular main chain leads to a remarkable change in the degradation mechanism. The thermal stability of ENR is worse than that of NR. For the first thermooxidative degradation stage, the thermal decomposition mechanism of ENR is similar to that of NR, which corresponds to a mechanism involving one-dimensional diffusion. For the second stage, the thermal decomposition mechanism of ENR is a three-dimensional diffusion, which is more complex than that of NR. Kinetic analysis showed that activation energy (E?), activation entropy (?H) and activation Gibbs energy (?G) values are all positive, indicating that the thermooxidative degradation process of ENR is non-spontaneous.

Studies on the properties and the thermal decomposition kinetics of natural rubber prepared with calcium chloride

To evaluate calcium chloride coagulation technology, two kinds of raw natural rubber samples were produced by calcium chloride and acetic acid respectively. Plasticity retention index (PRI), thermal degradation process, thermal degradation kinetics and differential thermal analysis of two samples studied. Furthermore, thermal degradation activation energy, pre-exponential factor and rate constant were calculated. The results show that natural rubber produced by calcium chloride possesses good mechanical property and poor thermo-stability in comparison to natural rubber produced by acetic acid.

Crystalline polymorph transition in poly(vinylidene fluoride) (PVDF)/acrylic rubber(ACM)/clay partially miscible hybrid

This study investigates the intercalation of nanoclay in partially miscible blends of poly(vinylidene fluoride) (PVDF) and acrylic rubber(ACM). Transmission electron microscopy and X-ray diffraction technique were used to investigate the formation of nanoscale polymer blend/clay hybrids. Using Infrared spectroscopy and X-ray analysis, the different polymorph formation in PVDF nanocomposite and conjugated phases of partially miscible nanocomposite was studied. Nanoclay was found to induce β and γ polymorphs while ACM tend to induce α phase in this polymer system. It was shown that PVDF chains in ACM-rich phase of partially miscible nanocomposites interact with ACM chains which in return form α polymorph in the presence of ACM. Further observations revealed that nanoclay in α polymorph is wrapped by ACM molecules.

Kinetic model for thermal dehydrochlorination of chlorinated natural rubber with different chlorine content

A novel model for calculating dehydrochlorination kinetics at a lower temperature of chlorinated natural rubber (CNR) is presented. It has been observed that dehydrochlorination is complex and involves three different stages. A model that accounts for dehydrochlorination at lower temperature is proposed. The kinetic parameters are obtained from dehydrochlorination experiments at 60-90 °C. The results of the kinetic calculation show that the apparent activation energy decreases with an increment of chlorine content. Higher chlorine content CNR makes it easier to remove hydrochloric acid when heated, but its dehydrochlorination rate affected by temperature is significantly less than that of the sample with a lower chlorine content. The thermogravimetric/derivative thermogravimetry results show that the beginning temperature of thermo-oxidative degradation rises with the increment of chlorine content. During the heating process, the higher chlorine content CNR is more stable than the lower one. The results suggest the storage conditions and basis for selection of appropriate temperature for the preparation of CNR from latex.

Experimental study of the degradation of volatile organic compounds by photocatalytic oxidation using TiO2 pellets

A fixed bed photocatalytic reactor has been designed and built with a UV
radiation source. Ti02 pellets were placed on the three fixed beds within the
reactor. Acetone was used as an indicator of volatile organic compounds (VOCs) during the experiment. Under the flow rate of 12.75 l/min, the oxidation efficiencies were obtained at four different concentrations of acetone laden gas streams ranged from 40ppm to 250ppm. It was found that the lower the acetone concentration of the untreated inlet gas, the higher the oxidation efficiency; the obtained oxidation efficiency was in the range of 40-70% for various concentrations of untreated gases.

Basic Needs, Property Rights and Degradation Of Commons

A major problem in many developing countries is the degradation of commons. This degradation has occurred on account of the lack of fulfilment of the basic needs of the poor, free riding and ill–defined property rights. As these goods are essential for the survival of these people, they have to access these items from commons. This results in regular raids to common land for resources and also to private houses (for example, in New Delhi) which are not guarded for water. A variant of the agricultural household model is used to analyse the above problem. Several propositions are established and it is demonstrated that degradation can occur at both a low and high price of basic needs. This result has important policy implications as it demonstrates that land or common degradation cannot be solved by just using the price system. Properly defined property rights and provision of basic goods in kind may resolve the problem of degradation of commons.

Anaerobic degradation of organic materials - significance of the substrate surface area

In anaerobic degradation of substrates containing mainly particulate organic matter, solids hydrolysis is rate-limiting. In these investigations, the particle size of various substrates was reduced by comminution to support hydrolysis. Two positive effects of comminution were observed. For substrates with high fibre content, which are particularly resistant to biodegradation, a significant improvement of the degradation degree was observed as a result of comminution. Secondly, for all substrates tested, and particularly for those rich in fibres, the degradation rate of comminuted samples was significantly higher. The first reason for both effects is an increase of the sample surface area. Several methods for measuring the specific surface area of organic materials, including particle size analysis, Nitrogen-adsorption and enzyme adsorption, were used and compared for the purpose of this study, where the surface area accessible to microbial enzymes is critical. The significance of the surface area in anaerobic degradation of particulate substrates was investigated through a kinetic model where the hydrolysis rate was based on the sample surface area. Good agreements were obtained between model and experiments carried out with samples of various specific surface areas. These results reinforced the significance of the sample surface area in anaerobic degradation processes. However, other effects of comminution responsible for the increased degradation degree and degradation rate were identified and discussed. These include: the increase of dissolved compounds due to cell rupture, exposition of surface areas previously inaccessible for microbial degradation, and alteration of the sample structure such as the lignin-cellulose arrangements.

Photocatalytic degradation of dye effluent by titanium dioxide pillar pellets in aqueous solution

Photocatalytic oxidation (PCO) process is an effective way to deal with organic pollutants in wastewater which could be difficult to be degraded by conventional biological treatment methods. Normally the TiO2 powder in nanometre size range was directly used as photocatalyst for dye degradation in wastewater. However the titanium dioxide powder was arduous to be recovered from the solution after treatment. In this application, a new form of TiO2 (i.e. pillar pellets ranging from 2.5 to 5.3 mm long and with a diameter of 3.7 mm) was used and investigated for photocatalytic degradation of textile dye effluent. A test system was built with a flat plate reactor (FPR) and UV light source (blacklight and solar simulator as light source respectively) for investigating the effectiveness of the new form of TiO2. It was found that the photocatalytic process under this configuration could efficiently remove colours from textile dyeing effluent. Comparing with the TiO2 powder, the pellet was very easy to recovered from the treated solution and can be reused in multiple times without the significant change on the photocatalytic property. The results also showed that to achieve the same photocatalytic performance, the FPR area by pellets was about 91% smaller than required by TiO2 powder. At least TiO2 pellet could be used as an alternative form of photocatalyst in applications for textile effluent treatment process, also other wastewater treatment processes.

Degradation of VOCs by phototcatalytic oxidation reactor using TiO2 pellets

Volatile Organic Compounds (VOCs) are air pollutants that come from burning fossil fuels and industrial emissions. They have potentially adverse health effects being carcinogenic and highly persistent in the environment. The use of photocatalytic oxidation to remove VOCs has the potential to be applied in indoor air quality improvement and industrial emission control. A fixed bed photocatalytic reactor was designed and built. UV black light lamps were installed in the reactor to provide a source of UV radiation. A non-film titania media as pellets were placed on the three fixed beds within the reactor. Toluene and acetone were used as indicators of VOCs during the experiment. With a flow rate of 12.75l/min, the oxidation efficiencies were obtained at four different concentrations of acetone laden gas streams ranging from 40ppm to 250ppm. It was found that the lower the acetone concentration of the untreated inlet gas, the higher the oxidation efficiency. The oxidation efficiency was in the range of 40–70% for various concentrations of untreated gases. Two concentrations of toluene laden gas stream were also tested using the same reactor. The oxidation efficiencies were found as 50% for 120ppm toluene gas and 45% for 300ppm toluene gas. It was found that the times required for toluene to reach oxidization equilibrium have been halved than for acetone gas stream. Other parameters such as flow rate and UV intensity were also altered to see their effects on the oxidation efficiency. A full spectrum scan was carried out using a Bio-rad Infrared spectrometer. It was found that the main components of the treated gas stream from the outlet of the reactor were CO2 and water along with small amount of untreated acetone. The suspected intermediates of aliphatic hydrocarbons and CO were found in very minimal amounts or undetectable. The research experiments supported that the TiO2 pellets can work effectively in a fixed bed photocatalytic reactor and achieve significant oxidation efficiencies for degradation of toluene and acetone as indicators of VOCs.

Enhanced degradation efficiency of toluene using titania/silica photocatalysis as a regeneration process

Three kinds of titania/silica pellets were prepared using the sol-gel method with surface areas of 50.4m² g-1, 421.1m².g^-1 and 89.1m².g^-1. An annular reactor was designed and built to determine the degradation efficiency of toluene and to investigate the relationship between the adsorption and desorption-photocatalytic processes. Surface area is an important factor influencing the adsorption-photocatalytic efficiency. Higher surface areas of pellets contribute to high rates of conversion of toluene. Un-reacted toluene and reaction intermediates accumulating on their surface deactivated the titania/silica catalyst. To overcome this problem, the adsorption and regeneration process were alternated in a dual reactor system. Connecting or disconnecting the toluene feed gas enabled one reactor to adsorb toluene, while the second reactor was regenerated by photocatalysis. Using UV irradiation and titania/silica pellets with high BET surface area (421.1 m².g^-1), the alternating adsorption/regeneration processes kept the degradation efficiency of toluene at 90% after 8 hours operation. By improving the adsorption-photocatalysis efficiency, and minimising the generation and accumulation of intermediate on the surface of pellets, the method extended catalyst life and maintained a high degradation efficiency of toluene.

A `Rubber-hand` illusion reveals a relationship between perceptual body image and unhealthy body change

The ‘rubber-hand’ illusion, in which individuals misattribute tactile sensations felt by their hand to a rubber prosthetic hand that they see being stimulated, was employed to examine the relationship between perceptual body image and unhealthy body change in 128 volunteers. Variance in unhealthy body development in males (22%) and in bulimic symptomatology in both females and males (10%), was explained by susceptibility to the illusion. The illusion, which is relatively free from cognitive and emotional ‘contamination’, could be used to identify individuals most responsive to therapies designed to correct inaccurate body perceptions–individuals whose perceptual body image is malleable.