Synthesis of LiFePO4@carbon nanotube core-shell nanowires with a high-energy efficient method for superior lithium ion battery cathodes

A high-energy efficient method is developed for the synthesis of LiFePO4@CNT core-shell nanowire structures. The method consists of two steps: liquid deposition approach to prepare FePO4@CNT core-shell nanowires and solvothermal lithiation to obtain the LiFePO4@CNT core-shell nanowires at a low temperature. The solution phase method can be easily scaled up for commercial application. The performance of the materials produced by this method is evaluated in Li ion batteries. The one-dimensional LiFePO4@CNT nanowires offer a stable and efficient backbone for electron transport. The LiFePO4@CNT core-shell nanowires exhibit a high capacity of 132.8 mAh g^-1 at a rate of 0.2C, as well as high rate capability (64.4 mAh g^-1 at 20C) for Li ion storage.

The metabolic and cognitive energy costs of stabilising a high-energy interlimb coordination task

Kinematic (relative phase error), metabolic (oxygen consumption, heart rate) and attentional (baseline and cycling reaction times) variables were measured while participants practised a high energy-demanding, intrinsically unstable 90° relative phase coordination pattern on independent bicycle ergometers. The variables were found to be strongly inter-correlated, suggesting a link between emerging performance stability with practice and minimal metabolic and attentional cost. The effects of practice of 90° relative phase coordination on the performance of in-phase (0°-phase) and antiphase (180°-phase) coordination were investigated by measuring the relative phase attractor layouts and recording the metabolic and attentional cost of the three coordination patterns before and after practice. The attentional variables did not differ significantly between coordination patterns and did not change with practice. Before practice, the coordination performance was most accurate and stable for in-phase cycling, with antiphase next and 90°-phase the poorest. However, metabolic cost was lower for antiphase than either in-phase or 90°-phase cycling, and the pre-practice attractor layout deviated from that predicted on the basis of dynamic stability as an attractor state, revealing an attraction to antiphase cycling. After practice of 90°-phase cycling, in-phase cycling remained the most accurate and stable, with 90°-phase next and antiphase the poorest, but antiphase retained the lowest metabolic energy cost. The attractor layout had changed, with new attractors formed at the practised 90°-phase pattern and its symmetrical partner of 270°-phase. Considering both the pre- and post-practice results, attractors were formed at either a low metabolic energy cost but less stable (antiphase) pattern or at a more stable but higher metabolic energy cost (90°-phase) pattern, but in neither case at the most stable and accurate (in-phase) pattern. The results suggest that energetic factors affect coordination dynamics and that coordination modes lower in metabolic energy expenditure may compete with dynamically stable modes.

One-dimensional nanomaterials synthesized using high-energy ball milling and annealing process

One-dimensional (1D) nanomaterials including nanotubes, nanowires and nanorods have many new properties, functionalities and a large range of promising applications. A major challenge for these future industrial applications is the large-quantity production. We report that the ball milling and annealing process has the potential to achieve the mass production. Several examples including C, BN nanotubes and SiC, Zn nanowires are presented to demonstrate such capability. In addition, both size and structure of 1D nanomaterials can be controlled by varying processing conditions. New growth mechanisms involved in the process have been investigated and the high-energy ball milling has an important role in the formation of these 1D nanomaterials.

Anomalous evaporation behavior of ZnO powder milled mechanically under high-energy conditions

ZnO powder showed anomalous evaporation behavior after its mechanical milling treatment under high-energy conditions. The amount of generated vapor is about 10 times higher in the first 15 min of annealing at 1300 °C than that of unmilled ZnO powders. The strong ball impacts are responsible for the greatly enhanced evaporation ability. Low-energy ball milling involving shearing actions and rare weak impacts leads only to a small evaporation rate enhancement. The possible explanation of the high evaporation rate of the heavily milled material is the existence of large fraction of weakly bonded atoms in grain boundaries, surface defects and strained areas.

Electrophoretic deposition of YSZ thin-film electrolyte for SOFCs utilizing electrostatic-steric stabilized suspensions obtained via high energy ball milling

This manuscript describes a facile alternative route to make thin-film yttria-stabilized zirconia (YSZ) electrolyte by liquid-phase assisted electrophoretic deposition utilizing electrostatic-steric stabilized YSZ suspension followed by sintering. Very fine YSZ particles in ball-milled suspension facilitate their sustained dispersion through electrostatic mechanism as evidenced by their higher zeta potentials. Binder addition into the ball-milled suspension is also demonstrated to contribute complementary steric hindrance effects on suspension stability. As the consequence, the film quality and sinterability improve in the sequence of film made from non ball-milled suspension, film made from ball-milled suspension and film made from ball-milled suspension with binder addition. The specific deposition mechanisms pertaining to each suspension are also postulated and discussed below. A very thin dense electrolyte layer of ∼10 μm can be achieved via electrophoretic deposition route utilizing ball-milled suspension and binder addition. This in turn, makes the electrolyte resistance a more negligible part of the overall cell resistance. Further on, we also tested the performance of SOFC utilizing as-formed 10 μm YSZ electrolyte i.e. YSZ-NiO|YSZ|LSM (La0.8Sr0.2MnO3-δ), whereby a maximum power density of ∼850 mW cm−2 at 850 °C was demonstrated.

Compressibility of a Ti-based alloy with varying amounts of surfactant prepared by high-energy ball milling

The combined effects of varying amounts of surfactant (ethylene bis-stearamide; EBS) and milling time on the compressibility of ball-milled Ti-10Nb-3Mo (wt.%) alloy were investigated. Ball milling process was performed on the elemental powders with different amounts of EBS (0-3. wt.%) for 5 and 10. h, and the ball-milled powders were consolidated by a uniaxial cold pressing in the range of 500-1100. MPa. Results indicated that the addition of surfactant in ball milling process lead to significant changes in particle packing density. The relative density was higher for powders ball milled with larger amounts of EBS and for the shorter milling time. The compressibility of powders was examined by the compaction equation developed by Panelli and Ambrosio Filho. The densification parameter (A) increased with the increasing amount of EBS, and decreased with increasing milling time.

Simultaneous improvement in the strength and corrosion resistance of Al via high-energy ball milling and Cr alloying

The corrosion resistance and mechanical properties of nanocrystalline aluminium (Al) and Al-20. wt.%Cr alloys, synthesized by high-energy ball milling followed by spark plasma sintering, were investigated. Both alloys exhibited an excellent combination of corrosion resistance and compressive yield strength, which was attributed to the nanocrystalline structure, extended solubility, uniformly distributed fine particles, and homogenous microstructure induced by high-energy ball milling. This work demonstrates the possibilities of developing ultra-high strength Al alloys with excellent corrosion resistance, exploiting conventionally insoluble elements or alloying additions via suitable processing routes.

Wave exposure as a predictor of benthic habitat distribution on high energy temperate reefs

The new found ability to measure physical attributes of the marine environment at high resolution across broad spatial scales has driven the rapid evolution of benthic habitat mapping as a field in its own right. Improvement of the resolution and ecological validity of seafloor habitat distribution models has, for the most part, paralleled developments in new generations of acoustic survey tools such as multibeam echosounders. While sonar methods have been well demonstrated to provide useful proxies of the relatively static geophysical patterns that reflect distribution of benthic species and assemblages, the spatially and temporally variable influence of hydrodynamic energy on habitat distribution have been less well studied. Here we investigate the role of wave exposure on patterns of distribution of near-shore benthic habitats. A high resolution spectral wave model was developed for a 624 km2 site along Cape Otway, a major coastal feature of western Victoria, Australia. Comparison of habitat classifications implemented using the Random Forests algorithm established that significantly more accurate estimations of habitat distribution were obtained by including a fine-scale numerical wave model, extended to the seabed using linear wave theory, than by using depth and seafloor morphology information alone. Variable importance measures and map interpretation indicated that the spatial variation in wave-induced bottom orbital velocity was most influential in discriminating habitat classes containing the canopy forming kelp Ecklonia radiata, a foundation kelp species that affects biodiversity and ecological functioning on shallow reefs across temperate Australasia. We demonstrate that hydrodynamic models reflecting key environmental drivers on wave-exposed coastlines are important in accurately defining distributions of benthic habitats. This study highlights the suitability of exposure measures for predictive habitat modeling on wave-exposed coastlines and provides a basis for continuing work relating patterns of biological distribution to remotely-sensed patterns of the physical environment.

Corrosion behaviour and hardness of in situ consolidated nanostructured Al and Al-Cr alloys produced via high-energy ball milling

This paper presents a hypothesis and its experimental validation that simultaneous improvement in the hardness and corrosion resistance of aluminium can be achieved by the combination of suitable processing route and alloying additions. More specifically, the corrosion resistance and hardness of Al- xCr (x= 0-10 wt.%) alloys as produced via high-energy ball milling were significantly higher than pure Al and AA7075-T651. The improved properties of the Al- xCr alloys were attributed to the Cr addition and high-energy ball milling, which caused nanocrystalline structure, extended solubility of Cr in Al, and uniformly distributed fine intermetallic phases in the Al-Cr matrix.

Effect of thermomechanical processing on the microstructure and retained austenite stability during in situ tensile testing using synchrotron X-Ray diffraction of NbMoAl TRIP steel

In this work we compare and contrast the stability of retained austenite during tensile testing of Nb-Mo-Al transformation-induced plasticity steel subjected to different thermomechanical processing schedules. The obtained microstructures were characterised using optical metallography, transmission electron microscopy and X-ray diffraction. The transformation of retained austenite to martensite under tensile loading was observed by in-situ high energy X-ray diffraction at 1ID / APS. It has been shown that the variations in the microstructure of the steel, such as volume fractions of present phases, their morphology and dimensions, play a critical role in the strain-induced transition of retained austenite to martensite.

In situ synchrotron X-ray diffraction studies of the effect of microstructure on tensile behavior and retained austenite stability of thermo-mechanically processed transformation induced plasticity steel

Transmission electron microscopy and in situ synchrotron high-energy X-ray diffraction were used to investigate the martensitic transformation and lattice strains under uniaxial tensile loading of Fe-Mn-Si-C-Nb-Mo-Al Transformation Induced Plasticity (TRIP) steel subjected to different thermo-mechanical processing schedules. In contrast with most of the diffraction analysis of TRIP steels reported previously, the diffraction peaks from the martensite phase were separated from the peaks of the ferrite-bainite α-matrix. The volume fraction of retained γ-austenite, as well as the lattice strain, were determined from the diffraction patterns recorded during tensile deformation. Although significant austenite to martensite transformation starts around the macroscopic yield stress, some austenite grains had already experienced martensitic transformation. Hooke's Law was used to calculate the phase stress of each phase from their lattice strain. The ferrite-bainite α-matrix was observed to yield earlier than austenite and martensite. The discrepancy between integrated phase stresses and experimental macroscopic stress is about 300 MPa. A small increase in carbon concentration in retained austenite at the early stage of deformation was detected, but with further straining a continuous slight decrease in carbon content occurred, indicating that mechanical stability factors, such as grain size, morphology and orientation of the retained austenite, played an important role during the retained austenite to martensite transformation.

11B nuclear magnetic resonance study of boron nitride nanotubes prepared by mechano-thermal method

We reported ¹¹B nuclear magnetic resonance studies of boron nitride (BN) nanotubes prepared by mechano-thermal route. The NMR lineshape obtained at 192.493 MHz (14.7 T) was fitted with two Gaussian functions, and the ¹¹B nuclear magnetization relaxations were satisfied with the stretched–exponential function, exp[-(tlT₁)^(D+1)/6] (D: space dimension) at all temperatures. In addition, the temperature dependence of spin–lattice relaxation rates was well described by T_i^-1 = aT (a: constant, T: temperature) and could be understood in terms of direct phonon process. All the 11BNMR results were explained by considering the inhomogeneous distribution of the paramagnetic metal catalysts, such as α-Fe, Fe–N, and Fe₂ B, that were incorporated during the process of high-energy ball milling of boron powder and be synthesized during subsequent thermal annealing. X-ray powder diffraction as well as electron paramagnetic resonance (EPR) on BN nanotubes were also conducted and the results obtained supported these conclusions.

Plasma-assisted self-catalytic vapour-liquid-solid growth of β-SiC nanowires

Long and straight β-SiC nanowires are synthesized via the direct current arc discharge method with a mixture of silicon, graphite and silicon dioxide as the precursor. Detailed investigations with x-ray diffraction, scanning electron microscopy, energy dispersive x-ray spectroscopy, Raman scattering spectroscopy, transmission electron microscopy and selected area electron diffraction confirm that the β-SiC nanowires, which are about 100–200 nm in stem diameter and 10–20 µm in length, consist of a solid single-crystalline core along the (1 1 1) direction wrapped with an amorphous SiO_x layer. A broad photoluminescence emission peak with a maximum at about 336 nm is observed at room temperature. A direct current arc plasma-assisted self-catalytic vapour–liquid–solid process is proposed as the growth mechanism of the β-SiC nanowires. This synthesis technique is capable of producing SiC nanowires free of metal contamination with a preferential growth direction and a high aspect ratio, without the designed addition of transition metals as catalysts.

Poly(triazine imide) with intercalation of Lithium and ChlorideiIons [(C3N3)2(NHxLi1−x)3⋅LiCl]: A Crystalline 2D Carbon Nitride network

Poly(triazine imide) with intercalation of lithium and chloride ions (PTI/Li+Cl−) was synthesized by temperature-induced condensation of dicyandiamide in a eutectic mixture of lithium chloride and potassium chloride as solvent. By using this ionothermal approach the well-known problem of insufficient crystallinity of carbon nitride (CN) condensation products could be overcome. The structural characterization of PTI/Li+Cl− resulted from a complementary approach using spectroscopic methods as well as different diffraction techniques. Due to the high crystallinity of PTI/Li+Cl− a structure solution from both powder X-ray and electron diffraction patterns using direct methods was possible; this yielded a triazine-based structure model, in contrast to the proposed fully condensed heptazine-based structure that has been reported recently. Further information from solid-state NMR and FTIR spectroscopy as well as high-resolution TEM investigations was used for Rietveld refinement with a goodness-of-fit (χ2) of 5.035 and wRp=0.05937. PTI/Li+Cl− (P63cm (no. 185); a=846.82(10), c=675.02(9) pm) is a 2D network composed of essentially planar layers made up from imide-bridged triazine units. Voids in these layers are stacked upon each other forming channels running parallel to [001], filled with Li+ and Cl− ions. The presence of salt ions in the nanocrystallites as well as the existence of sp2-hybridized carbon and nitrogen atoms typical of graphitic structures was confirmed by electron energy-loss spectroscopy (EELS) measurements. Solid-state NMR spectroscopy investigations using 15N-labeled PTI/Li+Cl− proved the absence of heptazine building blocks and NH2 groups and corroborated the highly condensed, triazine-based structure model.