Modelling and testing of long range battery electric vehicle performance

There are two significant issues facing road transport in the medium to long term: the depletion of cheap oil reserves and the need to reduce carbon emissions. A long term solution for passenger cars could be the introduction of battery electric vehicles (BEVs). However, one of the main problems associated with the current generation of BEVs is their short range relative to conventional internal combustion engine (ICE) cars.

To investigate this issue, a long range battery electric vehicle, the UltraCommuter (UC), was constructed by the University of Waikato in partnership with HybridAuto Ltd. This paper describes the development, modelling and testing of the UC and its performance in the 2007 World Solar Challenge.

Expansion of congested railway capacity using triple-track line operation based on hourly passenger demand

This paper proposes a method of improving level of service in congested urban railways by means of a triple-track line operation for a highly dense urban area with special travel demand characteristics. Where the future travel demand forecasts show sluggish growth or no growth at all, there is little to no incentives for heavy railway investments like quadruple-track extension and construction of new railway routes to alleviate current railway congestion problems. In such a situation, triple-track line operation can be the best alternative due to its moderate investment cost and ease in land acquisition for just an additional single track along the existing tracks. Our simulation investigation in one of the congested railway lines in Tokyo showed that triple track line operation increases railway capacity by 26% and shortens travel time by 38% in peak direction during morning peak hours. These results are encouraging and are useful for removing current railways problems in Tokyo and in similar urban situations elsewhere.

At home on the road? Can drivers' relationships with their cars be associated with territoriality?

The current research explores the relationship between people and their cars within the framework of Altman's theory of human territoriality. It further develops the research of Sandqvist by examining the descriptions given by people with differing ownership and uses of their cars and exploring the congruence between these and the characteristics used to describe human territories. Thirteen focus groups were held with young drivers between the ages of 18 and 25 years, drivers over the age of 25 who are parents of pre-license age children, drivers over the age of 25 who do not regularly transport children, and drivers of work vehicles. Analyses of discussions revealed that drivers’ descriptions of the relationship with their car could be matched with Brown and Altman's descriptions of territory types. However, variations existed both between and within individuals as to the application of the labels ‘primary’, ‘secondary’ and ‘public’ territory to the car. Implications for the understanding of road user behaviour and the further development of theory on the car as a place or an object in terms of territoriality are discussed.

The feasibility of a sustainable energy, driver-only electric commuter vehicle for New Zealand

This paper investigates whether low technology driver-only, battery electric commuter vehicles are feasible for New Zealand. Personal passenger transport faces several challenges in the coming decades: depletion of cheap oil reserves, increasing congestion, localised pollution, the need for reduced carbon emissions and the long term goal of sustainability. One way of solving some of these problems could be to introduce low cost, comfortable, energy efficient, driver-only electric vehicles. These would still give the driver a weatherproof, safe and comfortable means of commuting, but at a fraction of the energy and running costs of conventional petrol/diesel cars. To help assess their viability, the performance and energy use of the E-POD electric commuter vehicle is used as a benchmark. The work shows that such a vehicle could be made cheaply, using readily available technology with a range of 180km and a top speed of over 90km/h. The chassis could be made from natural fibre composite materials that might reduce significantly the embedded energy required for its manufacture. The electricity taken from the grid to charge the batteries could be replaced by electricity generated from grid connected photovoltaic panels mounted on the garage roof of the vehicle owner.

Comparison of static and dynamic engine models on the transient performance of a passenger vehicle powertrain

This paper presents experimental and computational results obtained on the Ford Barra 190 4.0 litres I6 gasoline engine and on the Ford Falcon car equipped with this engine. Measurements of steady engine performance, fuel consumption and exhaust emissions were first collected using an automated test facility for a wide range of cam and spark timings vs. throttle position and engine speed. Simulations were performed for a significant number of measured operating points at full and part load by using a coupled Gamma Technologies GT-POWER/GT-COOL engine model for gas exchange, combustion and heat transfer. The fluid model was made up of intake and exhaust systems, oil circuit, coolant circuit and radiator cooling air circuit. The thermal model was made up of finite element components for cylinder head, cylinder, piston, valves and ports and wall thermal masses for pipes. The model was validated versus measured steady state air and fuel flow rates, cylinder pressure parameters, indicated and brake mean effective pressures, and temperature of metal, oil and coolant in selected locations. Computational results agree well with experiments, demonstrating the ability of the approach to produce fairly accurate steady state maps of BMEP and BSFC, as well as to optimize engine operation changing geometry, throttle position, cam and spark timing. Measurements of the transient performance and fuel consumption of the full vehicle were then collected over the NEDC cycle. Simulations were performed by using a coupled Gamma Technologies GT-POWER/GT-COOL/GT-DRIVE model for instantaneous engine gas exchange, combustion and heat transfer and vehicle motion. The full vehicle model is made up of transmission, driveshaft, axles, and car components and the previous engine model. The model was validated with measured fuel flow rates through the engine, engine throttle position, and engine speed and oil and coolant temperatures in selected locations. Instantaneous engine states following a time dependent demand for torque and speed differ from those obtained by interpolating steady state maps of BSFC vs. BMEP and speed. Computational results agree well with experiments, demonstrating the utility of the approach in providing a more accurate prediction of the fuel consumption over test cycles.

Why do people buy hybrid cars?

This article reports on the underlying dimensions used by petrol-electric hybrid and conventional car buyers when evaluating a vehicle with the intent to purchase. Buyers of conventionally fuelled vehicles reported that they considered quality and performance as the most important determinants of choice. They rated as least important, the image they derive from driving a particular car and social influence. On the other hand, petrol-electric hybrid car buyers reported that social influence and projecting a “green” image were most important considerations and quality and appeal were least important. These findings provide social marketers with a crucial understanding that helps in the selection of an appropriate model to promote the diffusion of eco-friendly vehicles.

Timing and frequency data for passenger divesting at Melbourne domestic airport

The data covers the timing and frequency for divesting in the passenger screening process at Melbourne Airport, Victoria. Divesting is defined as the process of removing items from one's person before going through the screening process and placing them and cabin luggage onto the X-ray conveyor. This may also include removing items from bags to assist in the screening process.

Timing and frequency data for passenger divesting at Sydney domestic airport

The data covers the timing and frequency for divesting in the passenger screening process at Sydney Airport, New South Wales. Divesting is defined as the process of removing items from one's person before going through the screening process and placing them and cabin luggage onto the X-ray conveyor. This may also include removing items from bags to assist in the screening process.

Timing and frequency data for passenger divesting at Adelaide domestic airport

The data covers the timing and frequency for divesting in the passenger screening process at Adelaide Airport, South Australia. Divesting is defined as the process of removing items from one's person before going through the screening process and placing them and cabin luggage onto the X-ray conveyor. This may also include removing items from bags to assist in the screening process.

Timing and frequency data for passenger composing at Melbourne domestic airport

The data covers the timing and frequency for composing in the passenger screening process at Melbourne Airport, Victoria. Composing is defined as the process of collecting personal items after the screening process.