48 resultados para Radio frequency modulation.
em Deakin Research Online - Australia
Resumo:
In this chapter the authors discuss the physical insight of the role of wireless communication in RFID systems. In this respect, this chapter gives a brief introduction on the wireless communication model followed by various communication schemes. The chapter also discusses various channel impairments and the statistical modeling of fading channels based on the environment in which the RFID tag and reader may be present. The chapter deals with the fact that the signal attenuations can be dealt with up to some level by using multiple antennas at the reader transmitter and receiver to improve the performance. Thus, this chapter discusses the use of transmit diversity at the reader transmitter to transmit multiple copies of the signal. Following the above, the use of receiver combining techniques are discussed, which shows how the multiple copies of the signal arriving at the reader receiver from the tag are combined to reduce the effects of fading. The chapter then discusses various modulation techniques required to modulate the signal before transmitting over the channel. It then presents a few channel estimation algorithms, according to which, by estimating the channel state information of the channel paths through which transmission takes place, performance of the wireless system can be further increased. Finally, the Antenna selection techniques are presented, which further helps in improving the system performance.
Resumo:
Radio Frequency Identification Technology (RFIO) has been explored for various process enhancements in clinical contexts, particularly hospitals, for asset tracking. The technology has been accepted in such environments, as it is inexpensive and, in principle, uncomplicated to integrate with other clinical support systems. It is perceived to offer many benefits to currently resource critical/strained clinical environments. This research investigation focuses on the exploitation of the potential of the technology, to enhance processes in clinical environments. In this paper, the researchers aimed to uncover if the technology, as presently deployed, has been able to achieve its potential and, in particular, if it has been fully integrated into processes in a way that maximises the benefits that were perceived. This research is part of a larger investigation that aims to develop a meta-model for integration of RFIO into processes in a form that will maximise benefits that may be achievable in clinical environments. As the first phase of the investigation, the key learning from a clinical context (hospital), which has deployed RFIO and attempted to integrate it into the processes, to enable better efficiencies, is presented in this paper. The case method has been used as a methodological framework. Two clinical contexts (hospitals) are involved in the larger project, which constitutes two phases. In Phase 1, semi structured interviews were conducted with a selected number of participants involved with the RFIO deployment project, before and after, in clinical context 1 (hereinafter named as CCl). The results were then synthesised drawing a set of key learning, from different viewpoints (implementers and users), as reported in this paper. These results outline a linear conduit for a new proposed implementation (CC2). On completion of the phase II, the researchers aim to construct a meta-model for maximising the potential of RFIO in clinical contexts. This paper is limited to the first phase that aims to draw key learning to inform the linear conduit.
Resumo:
Radio Frequency Identification is a radical technology that is being experimented in hospitals commonly for tracking high value equipment, in order to maximize the efficiency of processes. RFID deployment and integration is mostly vendor and business driven, and hence its potential is not maximized. In this chapter, we propose a strategic framework to develop a process model, that will assist in maximizing the potential of RFID in hospitals.
Resumo:
Improvement of the binding of polypyrrole with PVDF (polyvinylidene fluoride) thin film using low pressure plasma was studied. The effects of various plasma gases i.e., Ar, O2 and Ar + O2 gases on surface roughness, surface chemistry and hydrophilicity were noted. The topographical change of the PVDF film was observed by means of scanning electron microscopy and chemical changes by X-ray photoelectron spectroscopy, with adhesion of polypyrrole (PPy) by abrasion tests and sheet resistance measurements. Results showed that the increase in roughness and surface functionalization by oxygen functional groups contributed to improved adhesion and Ar + O2 plasma gave better adhesion.
Resumo:
Tariq worked in the area of electronic textiles. He coated polyester fabric and PVDF films with polypyrrole. Plasma treatment was used to improve binding of coatings over the surface. He investigated in detail, the factors responsible for adhesion improvement using XPS, AFM, SEM, contact angle, abrasion tests and conductivity measurements. Different plasma gases, plasma power and plasma modes were investigated to get optimum bonding data. His investigations pointed towards improved surface oxygen functionalization and suitable surface morphology for improved bonding.
Resumo:
This paper presents the development of an energy harvesting circuit for use with a head-mountable deep brain stimulation (DBS) device. It consists of a circular planar inverted-F antenna (PIFA) and a Schottky diode-based Cockcroft-Walton 4-voltage rectifier. The PIFA has the volume of π × 10(2) × 1.5 mm(3), resonance frequency of 915 MHz, and bandwidth of 16 MHz (909-925 MHz) at a return loss of -10 dB. The rectifier offers maximum efficiency of 78% for the input power of -5 dBm at a 5 kΩ load resistance. The developed rectenna operates efficiently at 915 MHz for the input power within -15 dBm to +5 dBm. For operating a DBS device, the DC voltage of 2 V is recorded from the rectenna terminal at a distance of 55 cm away from a 26.77 dBm transmitter in free space. An in-vitro test of the DBS device is presented.
Resumo:
Radio Frequency Identification (RFlD) technology is increasingly being explored for deployment in hospitals to improve their existing processes. In recent years, RPID pilots has lead to full scale implementation in hospitals, especially for tracking of expensive equipment as well as movable assets that are critical in surgeries. However, academic research is yet to emerge with a generic process model that can be adapted contextually for deployment of RPID in particular hospital settings. In this paper, we propose an action research framework for a pilot implementation of RPID in a large Indian hospital, the experiences of which will contribute to and result, in the development of such a process model.
Resumo:
The 3rd generation partnership project (3GPP) long term evolution (LTE) standard uses single carrier frequency division multiple access (SCFDMA) scheme for the uplink transmissions and orthogonal frequency division multiplexing access (OFDMA) in downlink. SCFDMA uses DFT spreading prior to OFDMA modulation to map the signal from each user to a subset of the available subcarriers i.e., single carrier modulation. The efficiency of a power amplifier is determined by the peak to average power ratio (PAPR) of the modulated signal. In this paper, we analyze the PAPR in 3GPP LTE systems using root raised cosine based filter. Simulation results show that the SCFDMA subcarrier mapping has a significantly lower PAPR compared to OFDMA. Also comparing the three forms of SCFDMA subcarrier mapping, results show that interleave FDMA (IFDMA) subcarrier mapping with proposed root raised cosine filter reduced PAPR significantly than localized FDMA (LFDMA) and distributed (DFDMA) mapping. This improves its radio frequency (RF) power amplifier efficiency and also the mean power output from a battery driven mobile terminal.
Resumo:
In an environmental context, the use of RFID (radio frequency identification) and load cell sensor technology can be employed for not only bringing down waste management costs, but also to facilitate automating and streamlining waste (e.g., garbage, recycling, and green) identification and weight measurement processes for designing smart waste management systems. In this paper, we outline a RFID and sensor model for designing a system in real-time waste management. An application of the architecture is described in the area of RFID and sensor based automatic waste identity, weight, and stolen bins identification system (WIWSBIS).
Resumo:
Glow-Discharge Optical Emission Spectrometry (GD-OES) is a powerful technique for the rapid analysis of elements in a solid surface as a function of depth. DC-GD-OES allows depth profiling on electrically conductive surfaces only, and has proven to be difficult for the analysis of insulating layers, such as oxides. However, the technique of radio-frequency (RF) GD-OES has the advantage of being able to depth profile through multiple layers, both conducting and insulating. In this work, a LECO GDS- 850A spectrometer was calibrated for aluminium, oxygen, and other elements, with the RF source installed. A quantitative depth profile for a sample of tempered aluminium alloy 7475 is presented and compared with earlier work[1,2].
Resumo:
The use of RHFID (Radio Frequency ldentification) technology can be employed for not only reducing companies management costs but also to track uniquely each shipping container, pallet, case, and product being manufactured, shipped and sold, to increase visibility and accountability in the supply chain. RFID technology connects the supply chain players (i.e., suppliers, manifacturers, distributors, retailers and customers) and allows them to exchange data and product information. Despite these potential benefits, there are challenges and obstacles with the deployment of a RFID-enabled system in the global supply chain. The paper outlines the major RFID issues faced by supply chain management. In this paper, we also present a case study on pharmaceutical supply chain management (SCM) applications by addressing and examining the issues of RFID implementation in a SCM system.
Resumo:
Vocal variation may be important in population divergence. We studied geographical variation in contact calls of parrots of the crimson rosella, Platycercus elegans, complex, which is characterized by striking geographical plumage coloration variation. This complex has long been considered a rare example of a ring species (where two divergent forms coexist in sympatry but are connected by a chain of intermediate populations forming a geographical ring). We tested whether contact call variation is consistent with the ring species hypothesis. We recorded calls throughout the ring, including several sites from the three main population groups forming the ring and interfaces between them. We analysed duration, peak frequency, fundamental frequency and frequency modulation. We found significant differences, particularly in fundamental frequency and frequency modulation, at multiple biogeographical scales ranging from local populations to subspecies level. Discriminant function analyses showed some populations could be reliably discriminated from call structure. However, our results provided little support for three key predictions of the ring species hypothesis: (1) calls of the terminal, most divergent forms were not significantly different in three of the four acoustic variables, and differences did not appear to be maintained in sympatry, (2) phenotypically/geographically intermediate populations were not characterized by intermediate calls, and (3) call variation was not concordant with geographical sequence around the ring from one terminal form to the other. Our results underscore the emerging view that the evolutionary histories and phenotypic variability of many long-held ring species may be inadequately described by the ring species hypothesis and require alternative explanations. (C) 2008 The Association for the Study of Animal Behaviour. Published by Elsevier Ltd. All rights reserved.
Resumo:
The use of emerging technologies ( such as RFID - Radio Frequency Identification and remote sensing) can be employed to reduce health care costs and also to facilitate the automatic streamlining of infectious disease outbreak detection and monitoring processes in local health departments. It can assist medical practitioners with fast and accurate diagnosis and treatments. In this paper we outline the design and application of a real-time RFID and sensor-base Early Infectious (e.g., cholera) Outbreak Detection and Monitoring (IODM) system for health care.