Corner inlet and Nooramunga habitat mapping project

Deakin University and the University of Tasmania were commissioned by Parks Victoria (PV) to create two updated habitat maps for areas within the Corner Inlet and Nooramunga Marine and Coastal Park and Ramsar area. The team obtained a ground-truth data set using in situ video and still photographs. This dataset was used to develop and assess predictive models of benthic marine habitat distributions incorporating data from both ALOS (Advanced Land Observation Satellite) imagery atmospherically corrected by CSIRO and LiDAR (Light Detection and Ranging) bathymetry. This report describes the results of the mapping effort as well as the methodology used to produce these habitat maps.

Overall accuracies of habitat classifications were good, returning overall accuracies >73 % and kappa values > 0.62 for both study localities. Habitats predicted with highest accuracies included Zosteraceae in Nooramunga (91 %), reef in Corner Inlet (80 %), and bare sediment (no-visible macrobiota/no-visible seagrass classes; both > 76 %). The majority of classification errors were due to the misclassification of areas of sparse seagrass as bare sediment. For the Corner Inlet study locality the no-visible macrobiota (10,698 ha), Posidonia (4,608 ha) and Zosteraceae (4,229 ha) habitat classes covered the most area. In Nooramunga no-visible seagrass (5,538 ha), Zosteraceae (4,060 ha) and wet saltmarsh (1,562 ha) habitat classes were most dominant.

In addition to the commissioned work preliminary change detection analyses were undertaken as part of this project. These analyses indicated shifts in habitat extents in both study localities since the late 1990s/2000. In particular, a post-classification analysis highlighted that there were considerable increases in seagrass habitat (primarily Zosteraceae) throughout the littoral zones and river/creek mouths of both study localities. Further, the numerous channel systems remained stable and were free of seagrass at both times. A substantial net loss of Posidonia in the Corner Inlet locality is likely but requires further investigation due to potential misclassifications between habitats in both the 1998 map (Roob et al. 1998) and the current mapping. While the unsupervised Independent Components Analysis (ICA) change detection technique indicated some changes in habitat extent and distribution, considerable areas of habitat change observed in the post-classification approach are questionable, and may reflect misclassifications rather than real change. A particular example of this is an apparent large decrease in Zosteraceae and increase in Posidonia being related to the classification of Posidonia beds as Zosteraceae in the 1998 mapping. Despite this, we believe that changes indicated by both the ICA and post-classification approaches have a high likelihood of being ‘actual’ change. A pattern of gains and losses of Zosteraceae in the region north of Stockyard channel is an example of this. Further analyses and refinements of approaches in change detection analyses such as would improve confidence in the location and extent of habitat changes over this time period.

This work has been successful in providing new baseline maps using a repeatable method meaning that any future changes in intertidal and shallow water marine habitats may be assessed in a consistent way with quantitative error assessments. In wider use, these maps should also allow improved conservation planning, advance fisheries and catchment management, and progress infrastructure planning to limit impacts on the Inlet environment.

Evaluation of four supervised learning methods for benthic habitat mapping using backscatter from multi-beam sonar

An understanding of the distribution and extent of marine habitats is essential for the implementation of ecosystem-based management strategies. Historically this had been difficult in marine environments until the advancement of acoustic sensors. This study demonstrates the applicability of supervised learning techniques for benthic habitat characterization using angular backscatter response data. With the advancement of multibeam echo-sounder (MBES) technology, full coverage datasets of physical structure over vast regions of the seafloor are now achievable. Supervised learning methods typically applied to terrestrial remote sensing provide a cost-effective approach for habitat characterization in marine systems. However the comparison of the relative performance of different classifiers using acoustic data is limited. Characterization of acoustic backscatter data from MBES using four different supervised learning methods to generate benthic habitat maps is presented. Maximum Likelihood Classifier (MLC), Quick, Unbiased, Efficient Statistical Tree (QUEST), Random Forest (RF) and Support Vector Machine (SVM) were evaluated to classify angular backscatter response into habitat classes using training data acquired from underwater video observations. Results for biota classifications indicated that SVM and RF produced the highest accuracies, followed by QUEST and MLC, respectively. The most important backscatter data were from the moderate incidence angles between 30° and 50°. This study presents initial results for understanding how acoustic backscatter from MBES can be optimized for the characterization of marine benthic biological habitats. © 2012 by the authors.

Quantitative experimental comparison of single-beam, sidescan, and multibeam benthic habitat maps

Map comparison is a relatively uncommon practice in acoustic seabed classification to date, contrary to the field of land remote sensing, where it has been developed extensively over recent decades. The aim here is to illustrate the benefits of map comparison in the underwater realm with a case study of three maps independently describing the seabed habitats of the Te Matuku Marine Reserve (Hauraki Gulf, New Zealand). The maps are obtained from a QTC View classification of a single-beam echosounder (SBES) dataset, manual segmentation of a sidescan sonar (SSS) mosaic, and automatic classification of a backscatter dataset from a multibeam echosounder (MBES). The maps are compared using pixel-to-pixel similarity measures derived from the literature in land remote sensing. All measures agree in presenting the MBES and SSS maps as the most similar, and the SBES and SSS maps as the least similar. The results are discussed with reference to the potential of MBES backscatter as an alternative to SSS mosaic for imagery segmentation and to the potential of joint SBES–SSS survey for improved habitat mapping. Other applications of map-similarity measures in acoustic classification of the seabed are suggested.

Corner Inlet and Nooramunga Habitat Mapping Project – Part 2 : High resolution mapping and change detection analysis using 2011 Rapid Eye Satellite Image compared to 2009 ALOS Satellite Image

Building on a habitat mapping project completed in 2011, Deakin University was commissioned by Parks Victoria (PV) to apply the same methodology and ground-truth data to a second, more recent and higher resolution satellite image to create habitat maps for areas within the Corner Inlet and Nooramunga Marine and Coastal Park and Ramsar area. A ground-truth data set using in situ video and still photographs was used to develop and assess predictive models of benthic marine habitat distributions incorporating data from both RapidEye satellite imagery (corrected for atmospheric and water column effects by CSIRO) and LiDAR (Light Detection and Ranging) bathymetry. This report describes the results of the mapping effort as well as the methodology used to produce these habitat maps.

Overall accuracies of habitat classifications were good, with error rates similar to or better than the earlier classification (>73 % and kappa values > 0.58 for both study localities). The RapidEye classification failed to accurately detect Pyura and reef habitat classes at the Corner Inlet locality, possibly due to differences in spectral frequencies. For comparison, these categories were combined into a ‘non-seagrass’ category, similar to the one used at the Nooramunga locality in the original classification. Habitats predicted with highest accuracies differed from the earlier classification and were Posidonia in Corner Inlet (89%), and bare sediment (no-visible seagrass class) in Nooramunga (90%). In the Corner Inlet locality reef and Pyura habitat categories were not distinguishable in the repeated classification and so were combined with bare sediments. The majority of remaining classification errors were due to the misclassification of Zosteraceae as bare sediment and vice versa. Dominant habitats were the same as those from the 2011 classification with some differences in extent. For the Corner Inlet study locality the no-visible seagrass category remained the most extensive (9059 ha), followed by Posidonia (5,513 ha) and Zosteraceae (5,504 ha). In Nooramunga no-visible seagrass (6,294 ha), Zosteraceae (3,122 ha) and wet saltmarsh (1,562 ha) habitat classes were most dominant.

Change detection analyses between the 2009 and 2011 imagery were undertaken as part of this project, following the analyses presented in Monk et al. (2011) and incorporating error estimates from both classifications. These analyses indicated some shifts in classification between Posidonia and Zosteraceae as well as a general reduction in the area of Zosteraceae. Issues with classification of mixed beds were apparent, particularly in the main Posidonia bed at Nooramunga where a mosaic of Zosteraceae and Posidonia was seen that was not evident in the ALOS classification. Results of a reanalysis of the 1998-2009 change detection illustrating effects of binning of mixed beds is also provided as an appendix.

This work has been successful in providing baseline maps at an improved level of detail using a repeatable method meaning that any future changes in intertidal and shallow water marine habitats may be assessed in a consistent way with quantitative error assessments. In wider use, these maps should also allow improved conservation planning, advance fisheries and catchment management, and progress infrastructure planning to limit impacts on the Inlet environment.

Phase behavior and nanomechanical mapping of block ionomer complexes

Block ionomer complexes SSEBS-c-PCL were prepared, as a consequence of proton transfer from the sulfonic acid of sulfonated polystyrene-block- poly(ethylene-ran-butylene)-block-polystyrene (SSEBS) to the tertiary amine of a tertiary amine terminated poly(?-caprolactone) (APCL). The phase behavior of SSEBS-c-PCL was thoroughly investigated and the results showed that APCL in SSEBS-c-PCL displays unique crystallization behavior owing to the influence of interactions between the amine and sulfonic acid groups as well as the effects of confinement. Further, small-angle X-ray scattering study revealed that SSEBS-c-PCL displays a less ordered micro-phase structure compared to SSEBS. A quantitative mapping of mechanical properties at the nanoscale was achieved using peak force mode atomic force microscopy. It is found that the block ionomer complex possesses a higher average elastic modulus after complexation with crystallizable APCL. Additionally, the moduli for both hard and soft phases increase and the phase with higher modulus assignable to the hard SPS component shows much more pronounced changes after complexation, confirming that APCL interacts mainly with the SPS blocks. This provides an understanding of the composition and nanomechanical properties of these new block ionomer complexes and an alternative insight into the micro-phase structures of multi-phase materials.

Context matters: SETE mapping of teacher education in diverse contexts

The Studying the Effectiveness of Teacher Education (SETE) project (2010- ) investigates, as a priority, how well equipped teacher education graduates are to meet the requirements of diverse school settings. This paper outlines notions of diversity as reflected in large-scale longitudinal data sets including quantitative teacher and principal surveys (n=5,000+), national audit of teacher education programs (n=500+), and analysis of data from intensive case studies which track 170 graduate teachers through the first three years of their teaching career.

New opportunities for quantitative and time efficient 3D MRI of liquid and solid electrochemical cell components: Sectoral Fast Spin Echo and SPRITE.

The ability to image electrochemical processes in situ using nuclear magnetic resonance imaging (MRI) offers exciting possibilities for understanding and optimizing materials in batteries, fuel cells and supercapacitors. In these applications, however, the quality of the MRI measurement is inherently limited by the presence of conductive elements in the cell or device. To overcome related difficulties, optimal methodologies have to be employed. We show that time-efficient three dimensional (3D) imaging of liquid and solid lithium battery components can be performed by Sectoral Fast Spin Echo and Single Point Imaging with T1 Enhancement (SPRITE), respectively. The former method is based on the generalized phase encoding concept employed in clinical MRI, which we have adapted and optimized for materials science and electrochemistry applications. Hard radio frequency pulses, short echo spacing and centrically ordered sectoral phase encoding ensure accurate and time-efficient full volume imaging. Mapping of density, diffusivity and relaxation time constants in metal-containing liquid electrolytes is demonstrated. 1, 2 and 3D SPRITE approaches show strong potential for rapid high resolution (7)Li MRI of lithium electrode components.

Yaringa and French Island Marine National Park habitat mapping

Deakin University and the Department of Primary Industries were commissioned by ParksVictoria (PV) to create two updated habitat maps for Yaringa and French Island MarineNational Parks. The team obtained a ground-truth data set using in situ video and still photographs. This dataset was used to develop and assess predictive models of benthic marine habitat distributions incorporating data from World-View-2 imagery atmospherically corrected by CSIRO and LiDAR (Light Detection and Ranging) bathymetry. In addition, the team applied an unsupervised classification approach to an aerial photograph to assess the differences between the two remote sensors. This report describes the results of the mapping as well as the methodology used to produce these habitat maps.This study has provided mapping of intertidal and subtidal habitats of Yaringa and FrenchIsland MNPs at a 2 m resolution with fair to good accuracies (Kappa 0.40-0.75). These were combined with mangrove and saltmarsh habitats recently mapped by Boon et al. (2011) to provide compete-coverage habitat maps of Yaringa and French Island MNPs.The mapping showed that Yaringa MNP was dominated by mangroves, wet saltmarsh and dense Zostereaceae, covering 33%, 29% and 19%, respectively. Similarly, intertidalvegetation and subtidal vegetation (dominated by Zosteraceae) covered 26% and 25% ofFrench Island MNP. However, as a result of turbidity and missing satellite imagery 27% ofFrench Island MNP remains unmapped.The coupling of WV-2 and LiDAR reduced potential artefacts (e.g. sun glint causing whiteand black pixels known as the “salt and pepper effect”). The satellite classification appeared to provide better results than the aerial photography classification. However, since there is a two-year difference between the capture of the aerial photography and the collection of the ground-truth data this comparison is potentially temporally confounded. It must also be noted that there are differences in costs of the data,the spatial resolution between the two datasets (i.e. WV-2 = 2 m and the Aerial = 0.5 m) and the amount spectral information contained in the data (i.e. WV-2 = 8 bands and the aerial = 4 bands), which may ultimately determine its utility for a particular project.The spatial assessment using FRAGSTATs of habitat patches within Yaringa MNP provides a viable and cost effect way to assess habitat condition (i.e. shape, size and arrangement).This spatial assessment determined that dense Zosteraceae and NVSG habitat classeswere generally larger in patch size and continuity than the medium/sparse Zosteraceaehabitat. The application spatial techniques to time-series mapping may provide a way toremotely monitor the change in the spatial characteristics of marine habitats.This work was successful in providing new baseline habitat maps using a repeatable method meaning that any future changes in intertidal and shallow water marine habitats may be assessed in a consistent way with quantitative error assessments. In wider use, these maps should also allow improved conservation planning, fisheries and catchment management, and contribute toward infrastructure planning to limit impacts on Western Port.

The effect of chromate on the pitting susceptibility of AA7075-T651 studied using potentiostatic transients

The effect of chromate on metastable pitting of AA7075-T651 as determined via potentiostatic polarisation is reported. A systematic study of metastable pitting and its correlation with stable pits was conducted in various concentrations of sodium chromate (Na2CrO4), revealing the metastable pitting rate was able to provide a quantitative metric for pitting corrosion. The size and number of metastable pits decreased significantly in the presence of chromate. The present study is intended as a general baseline for the assessment of future chromate replacement technologies, as elaborated herein. © 2014 Elsevier Ltd.

Mutational interference mapping experiment (MIME) for studying RNA structure and function

RNA regulates many biological processes; however, identifying functional RNA sequences and structures is complex and time-consuming. We introduce a method, mutational interference mapping experiment (MIME), to identify, at single-nucleotide resolution, the primary sequence and secondary structures of an RNA molecule that are crucial for its function. MIME is based on random mutagenesis of the RNA target followed by functional selection and next-generation sequencing. Our analytical approach allows the recovery of quantitative binding parameters and permits the identification of base-pairing partners directly from the sequencing data. We used this method to map the binding site of the human immunodeficiency virus-1 (HIV-1) Pr55(Gag) protein on the viral genomic RNA in vitro, and showed that, by analyzing permitted base-pairing patterns, we could model RNA structure motifs that are crucial for protein binding.

The burden of neck pain: its meaning for persons with neck pain and healthcare providers, explored by concept mapping

PURPOSE: To empirically define the concept of burden of neck pain. The lack of a clear understanding of this construct from the perspective of persons with neck pain and care providers hampers adequate measurement of this burden. An additional aim was to compare the conceptual model obtained with the frequently used Neck Disability Index (NDI). METHODS: Concept mapping, combining qualitative (nominal group technique and group consensus) and quantitative research methods (cluster analysis and multidimensional scaling), was applied to groups of persons with neck pain (n = 3) and professionals treating persons with neck pain (n = 2). Group members generated statements, which were organized into concept maps. Group members achieved consensus about the number and description of domains and the researchers then generated an overall mind map covering the full breadth of the burden of neck pain. RESULTS: Concept mapping revealed 12 domains of burden of neck pain: impaired mobility neck, neck pain, fatigue/concentration, physical complaints, psychological aspects/consequences, activities of daily living, social participation, financial consequences, difficult to treat/difficult to diagnose, difference of opinion with care providers, incomprehension by social environment, and how person with neck pain deal with complaints. All ten items of the NDI could be linked to the mind map, but the NDI measures only part of the burden of neck pain. CONCLUSION: This study revealed the relevant domains for the burden of neck pain from the viewpoints of persons with neck pain and their care providers. These results can guide the identification of existing measurements instruments for each domain or the development of new ones to measure the burden of neck pain.