The reactivity of bis(para-methoxyphenyl)telluroxide towards triflic acid and diphenylphosphinic acid. Theoretical considerations of the protonation and hydration process of diorganotelluroxanes

The reaction of (p-MeOC₆H₄)₂TeO with two equivalents of HO₃SCF₃ and HO₂PPh₂ provided the tetraorganoditelluroxanes (F₃CSO₃)(p-MeOC₆H₄)₂TeOTe(p-MeOC₆H₄)₂(O₃SCF₃) (1) and (Ph₂PO₂)(p-MeOC₆H₄)₂TeOTe(p-MeOC₆H₄)₂(O₂PPh₂)·2 Ph₂PO₂H (2) in good yields. Compounds 1 and 2 were characterized by solution and solid-state ³¹P and ¹²⁵Te NMR spectroscopy, IR spectroscopy, electrospray mass spectrometry, conductivity measurements and single crystal X-ray diffraction. In solution, compound 1 undergoes an electrolytic dissociation and reversibly reacts with traces of water to give the mononuclear cation [(p-MeOC₆H₄)₂TeOH]⁺ and triflate anions. Theoretical aspects of the protonation and hydration of model telluroxanes R₂TeO (R = H, Me, Ph) were investigated by preliminary DFT calculations and compared to the corresponding selenoxanes R₂SeO. The tellurium dihydroxides R₂Te(OH)₂ seem to be more stable than the hydrogen-bonded complexes R₂TeO·H₂O.

Monolayer behavior of a pyridyl head-group-containing amphiphile and its miscibility with poly(D,L-lactide-co-glycolide) on different pH subphase

In this paper, we investigated the Langmuir film and Langmuir–Blodgett (LB) monolayer film of a nonionic amphiphilic molecule, 4-(6-p-pyridyloxyl)hexyloxyl-4′-dodecyloxylazobenzene (C12AzoC6Py) and its mixture with poly(d,l-lactide-co-glycolide) (PLG) at different subphase pH values (2.0, 2.6, 3.3, 4.4, and 6.5, respectively) by surface pressure–area (π–A) isotherms, in situ interface Brewster angle microscopy (BAM), and ex situ atomic force microscopy (AFM). For pure C12AzoC6Py, its π–A isotherms display a plateau when the subphase pH value is lower than 3.0. The pressure of the plateau increases with the decrease of pH until 2.0. Over the plateau, the π–A isotherms become almost identical to the one under neutral conditions. The appearance of such a plateau can be explained as the coexistence of protonation and unprotonation of pyridyl head groups of the employed amphiphile. In contrast to the homogeneous surface morphology of pure C12AzoC6Py near the plateau by BAM observation, the surface in the case of its mixing with PLG exhibits a dendritic crystalline state under low surface pressure at subphase pH lower than 3.0. The crystalline state becomes soft and gradually melts into homogeneous aggregates with surface pressure increasing to a higher value than that of the plateau. Meanwhile, the hydrolysis of PLG in the mixture system at the interface has been affirmed to be restrained to a very large extent. And the PLG was believed to be compelled to the up layer of the LB film due to the phase separation, which is examined by AFM. Based on the experimental results, the corresponding discussion was also performed.

Mechanisms governing the enhanced thermal stability of acid and base treated polypyrrole

One of the major problems associated with the use of polypyrrole (PPy) in a practical engineering application is its poor thermal stability at elevated temperatures, especially in the presence of oxygen and moisture. Several authors have shown that enhanced stability can be achieved through treatment with simple acids and bases. This paper presents a summary of the possible structural changes which occur as a result of these treatments and those that appear to be related to enhanced conductivity stability. A slight increase in conductivity (10–20%) is observed for acid treated PPy films which is found to be the result of protonation of the pyrrole structure. This effect is dramatically enhanced by treatment at high temperatures where an increase in conductivity of >84% can be achieved. Base treatment of the PPy films results in the deprotonation of the pyrrole structure leading to the loss of conductivity (>40%). Preliminary X-ray Photoelectron Spectroscopy (XPS) results indicate that both acid and base treatment resulted in the elimination of reactive sites for oxygen. Long term thermal ageing of these treated films were conducted at 150 °C in air. The conductivity decay behaviour was found to follow multiple first order chemical reaction kinetics.

New series of intramolecularly coordinated diaryltellurium compounds. Rational synthesis of the diarylhydroxytelluronium triflate [(8-Me 2NC 10H 6) 2Te(OH)](O 3SCF 3)

The reaction of 8-dimethylaminonaphthyllithium etherate with the tellurium(II) bis(dithiocarbamate) Te(S₂CNEt₂)₂ provided the diaryltelluride (8-Me₂NC₁₀H₆)₂Te (1). The oxidation of 1 with an excess of H₂O₂ did not afford the expected diaryltellurium(IV) oxide (8-Me₂NC₁₀H₆)₂TeO (2), but the diaryltellurium(VI) dioxide (8-Me₂NC₁₀H₆)₂TeO₂ (3). The preparation of 2 was achieved by the comproportionation reaction of 1 and 3. The protonation of 2 using triflic acid gave rise to the formation of diarylhydroxytelluronium triflate [(8-Me₂NC₁₀H₆)₂Te(OH)](O₃SCF₃) (4), which features the protonated diaryltellurium oxide [(8-Me₂NC₁₀H₆)₂Te(OH)]+ (4a). Compounds 1, 3·H₂O·H₂O₂, 3·2H₂O, and 4 were characterized by X-ray crystallography. The experimentally obtained molecular structures were compared to those calculated for 1–3, 4a, and (8-Me₂NC₁₀H₆)₂Te(OH)₂ (5) as well as the related diphenyltellurium compounds Ph₂Te (6), Ph₂TeO (7), Ph₂TeO₂ (8), [Ph₂Te(OH)]+ (9a), and Ph₂Te(OH)₂ (10) at the DFT/B3PW91 level of theory.