Finite element analysis of residual stresses in metallic coatings through a compound casting

Al and Mg alloys are widely used in industry as main lightweight alloys. They have excellent properties, such as low density, high ductility, and high specific strength, and so on. Generally speaking, Mg alloys are better than Al alloys. However the corrosion of Mg alloys is much more difficult to control compared Al alloys. Therefore to combine these two lightweight alloys, a composite-like structure is an ideal solution since Al alloys can be used as protective coatings for Mg alloys. Compound casting is a realistic technique to get this coating system. In the current study, we numerically study the compound casting using finite element method (FEM) to make these two alloys, a composite-like structure, satisfy requirements to resist corrosion required from industry, in which the aluminum layer is acting as a protective coating for the magnesium substrate. Several finite element models have been developed by using the birth and death element technique and we focus on compound casting-induced residual stresses in the compounded structure. The numerical results obtained from the proposed finite element models show the distribution profiles of thermal residual stresses. We found the major factors influencing the residual stresses are the temperature to pre-heating the Al substrate and the thickness of Mg deposits. © (2014) Trans Tech Publications, Switzerland.

Considerations associated with the testing of external pipeline coatings

Reliable testing methodologies for the assessment of protective coatings are critical for ensuring the integrity and durability of pipeline coatings (such as field joint coatings) and the mitigation of pipeline corrosion. Currently the failure of joint coatings is one of the major concerns in corrosion protection of pipelines, although they represent only approximately 5% of the coated area in a pipeline system. This paper presents an overview of major testing methodologies currently used in the pipeline industry for the selection, testing, and life prediction of coatings, in particular field joint coatings. Particular focus is on the discussion of difficulties and limitations in testing methods for assessing pipeline coating cracking, cathodic disbondment and loss of adhesion. It is shown that there are limitations in current methodologies in evaluating the coating flexibility - a key parameter for avoiding coatings cracking during hydrostatic testing, cyclic pressure operation and field bending. Methodologies for assessing the effect of holidays in coatings on the cathodic disbondment of pipeline coating under excessively negative cathodic protection (CP) voltages also require improvement. Furthermore, methods for understanding the effects of coating wet adhesion on pipeline coating, cracking and disbondment also need attention. Some preliminary results for addressing some of these issues are also presented in this paper.

Studying and evaluating anti-corrosion coatings and inhibitors using the wire beam electrode method in conjunction with electrochemical noise analysis

Purpose – To provide a summary of research work carried out mainly in the authors' group for evaluating various protective coatings including rustproofing oils, and also for studying corrosion inhibitors using the wire beam electrode (WBE) method.

Design/methodology/approach – A range of published papers published during the past 15 years was summarised and reviewed. Recent research work in the authors' group was also included, which involved the combined use of the WBE with electrochemical noise analysis and the scanning reference electrode technique.

Findings – The WBE method has been developed into a very useful tool of evaluating the performance of coatings and inhibitors. In particular, The WBE is uniquely applicable for determining the performance of coatings and inhibitors to control localised corrosion.

Research limitations/implications – Focusing mainly on recent research.

Practical implications – A useful source of information for researchers and graduate students working in the areas of organic coating and inhibitor research.

Originality/value – The first summary or review on this research topic.

An overview of methods for simulating and evaluating pipeline corrosion

Steel pipelines, buried under the soil and protected by the combination of protective coatings and cathodic protection (CP), are used for oil and gas transportation. These pipelines are one of the critical infrastructures for energy transportation and therefore became lifelines of modern society. The deterioration of the external surfaces of transmission pipelines is a serious problem and is caused mainly by coating and/or CP failure leading to the loss of integrity of pipelines. To avoid such damage, there is a need of techniques which are able to locate active corrosion sites, monitor corrosion, and evaluate corrosion damage. Fundamental understanding of such processes occurring on coated pipelines (with various types of defects in coatings as well as pipe) in complex soil environment is necessary for the development of such techniques. Numerous laboratory techniques, i.e., electrochemical impedance spectroscopy based, polarisation measurements based, mathematical simulations, direct observation etc. have been used to develop fundamental understanding, simulate and evaluate corrosion occurring in oil and gas pipelines under various operating conditions. Given the complex nature of the pipeline corrosion, application of these laboratory techniques in field measurements as well as in understanding the corrosion mechanisms is lacking. This paper presents an overview of investigations, based on electrochemical techniques, for simulation and evaluation of pipeline corrosion in laboratory.

An overview of new progresses in understanding pipeline corrosion

An approach to achieving the ambitious goal of cost effectively extending the safe operation life of energy pipeline to 100 years is the application of health monitoring and life prediction tools that are able to provide both long-term remnant pipeline life prediction and in-situ pipeline condition monitoring. A critical step is the enhancement of technological capabilities that are required for understanding and quantifying the effects of key factors influencing buried steel pipeline corrosion and environmentally assisted materials degradation, and the development of condition monitoring technologies that are able to provide in-situ monitoring and site-specific warning of pipeline damage. This paper provides an overview of our current research aimed at developing new sensors and electrochemical cells for monitoring, categorising and quantifying the level and nature of external pipeline and coating damages under the combined effects of various inter-related variables and processes such as localised corrosion, coating cracking and disbondment, cathodic shielding, transit loss of cathodic protection.

Nanoparticle coatings for UV protective textiles

As the intensity of UV radiation increases every year, effective methods to block UV rays to protect human skin, plastics, timber and other polymer materials are urgently sought. Textiles serve as important materials for UV protection in many applications. The utilisation of nanoparticles to textile materials has been the object of several studies aimed at producing finished fabrics with different performances. This article reviews the recent advancement in the field of UV blocking textiles and fibers that are functionalised with nanostructured surface coatings. Different types of UV blocking agents are discussed and various examples of UV blocking textiles utilising ZnO and TiO₂ are presented. Future challenges such as wash-fastness and photocatalysis are also discussed.

Studying the cathodic disbondment of coatings using electrochemical impedance spectroscopy

The disbondment of protective organic coatings is a widely reported pipeline coating failure mode in the oil and gas industry. Traditional methods of evaluating cathodic disbondment of pipeline coatings are based on visual inspection of pipeline conditions, and laboratory testing of cathodic disbondment resistance (CDR) using standard methods such as ASTM G8. Although some other laboratory-based techniques, such as scanning kelvin probe and scanning acoustic microscopy have been used to study the cathodic disbondment (CD) of coatings, these are often difficult to apply in practical testing. Over the past decade, electrochemical impedance spectroscopy (EIS) has been employed as a potential method for measuring CD. This paper reports preliminary results from an EIS study designed to characterise CD behaviour of epoxy coatings under excessive cathodic protection. EIS data correlated well with the area of disbonded coating. Analysis of EIS data can provide valuable information on the initiation and rates of CD.

An investigation of tribological properties of CN and TiCN coatings

Today the tool industry on a worldwide basis uses hard, wear-resistant, and low-friction coatings produced by different processes such as electrochemical or electroless methods, spray technologies, thermochemical, chemical-vapor deposition (CVD), and physical vapor deposition (PVD). In the current work, two different coatings, nitrocarburized (CN) and titanium carbonitride (TiCN) on M2-grade tool steel, were prepared by commercial diffusion and PVD techniques, respectively. Properties such as thickness, roughness, and hardness were characterized using a variety of techniques, including glow-discharge optical emission spectrometry (GD-OES) and scanning electron microscopy (SEM). A crossed-cylinders wear-testing machine was used to investigate the performances of both coatings under lubrication. The effect of coatings on the performance of lubricants under a range of wear-test conditions was also examined. Degradation of lubricants during tribological testing was explored by Fourier transform infrared (FTIR) spectroscopy.

Gambling and corporate social responsibility (CSR) : re-defining industry and state roles on duty of care, host responsibility and risk management

During the 1990s, states embraced legalised gambling as a means of supplementing state revenue. But gaming machines (EGMs, pokies, VLTs, Slots) have become increasingly controversial in countries such as Australia, Canada and New Zealand, which experienced unprecedented roll-out of gaming machines in casino and community settings; alongside revenue windfalls for both governments and the gambling industry. Governments have recognised that gambling results in a range of social and economic harms and, similar to tobacco and alcohol, have introduced public policies predicated on harm minimisation. Yet despite these, gaming losses have continued to climb in most jurisdictions, along with concerns about gambling-related harms. The first part of this article discusses an emerging debate in Ontario Canada, that draws parallels between host responsibility in alcohol and gambling venues. In Canada, where government owns and operates the gaming industry, this debate prompts important questions on the role of the state, duty of care and regulation ‘in the public interest’ and on CSR, host responsibility and consumer protection. This prompts the question: Do governments owe a duty of care to gamblers?

The article then discusses three domains of accumulating research evidence to inform questions raised in the Ontario debate: evidence that visible behavioural indicators can be used with high confidence to identify problem gamblers on-site in venues as they gamble; new systems using player tracking and loyalty data that can provide management with high precision identification of problem gamblers and associated risk (for protective interventions); and research on technological design features of new generation gaming products in interaction with players, that shows how EGM machines can be the site for monitoring/protecting players. We then canvass some leading international jurisdictions on gambling policy CSR and consumer protection.

In light of this new research, we ask whether the risk of legal liability poses a tipping point for more interventionist public policy responses by both the state and industry. This includes a proactive role for the state in re-regulating the gambling industry/products; instituting new forms of gaming machine product control/protection; and reinforcing corporate social responsibility (CSR) and host responsibility obligations on gambling providers – beyond self-regulatory codes. We argue the ground is shifting, there is new evidence to inform public policy and government regulation and there are new pressures on gambling providers and regulators to avail themselves of the new technology – or risk litigation

Polymer coatings containing nano particles of zinc oxide for the UV protection of dyed polyester fabrics

The useful life of many outdoor textile products is limited by degradation caused by exposure to sunlight, in particular by the ultra violet component (below 400 nm). The degradation results in fading of colours and also loss of physical properties, such as tear strength and abrasion resistance. Degradation can be decreased with UV absorbers, often used in conjunction with antioxidants or free radical quenchers. The protection afforded by these organic compounds is, however, limited as they are ultimately destroyed by the UV radiation they absorb.
An alternative approach is to coat fabrics with a polymer containing an inorganic UV absorber, such as zinc oxide. The inherent stability of zinc oxide would be expected to provide a protective effect over a much longer period than can be achieved with an organic UV absorber. A possible disadvantage of zinc oxide when applied in a polymer film is that absorption and scattering of visible light can produce hazy films and, hence, an unacceptable change in fabric appearance.
This poster paper examines the possibility of using nano particles of zinc oxide dispersed in acrylic polymers for protecting dyed polyester fabrics against sunlight fading. Factors affecting both UV absorbance and film clarity will be discussed. The possibility will also be examined that the protective effect may be reduced in some circumstances by reactive oxygen species, generated by the interaction of UV with zinc oxide in the presence of air and water.

Corrosion monitoring under disbonded coatings

Localized corrosion can occur under disbonded coatings threatening the safe operation of industry infrastructures such as underground oil and gas pipelines. Currently the assessment of localised corrosion under coating defects is a major technical challenge. The application of corrosion probes to monitor corrosion under disbonded coating also remains a difficulty. This paper presents a new corrosion sensor concept capable of electrochemically measuring corrosion rates under disbonded coatings on cathodically protected structures such as energy pipelines. Examples of its capabilities are illustrated with experimental data obtained in low conductivity aqueous solutions.

The effects of mechanical stress, environment and cathodic protection on the degradation and failure of coatings: An overview

Organic coatings have been used in conjunction with cathodic protection as the most economical method of corrosion protection by the oil and gas pipeline industry. In a bid to prolong the life of the pipelines, the degradation and failure of pipeline coatings under the effects of major influencing factors including mechanical stress, the environmental corrosivity and cathodic protection have been extensively investigated over the past decades. This paper provides an overview of recent research for understanding coating degradation under the effect of these factors, either individually or in combination. Electrochemical impedance spectroscopy remains the primary and the most commonly used technique of studying the degradation of organic coatings, although there have been attempts to use other techniques such as electrochemical polarization (both dynamic and static), electrochemical noise, Scanning Kelvin Probe, Fourier Transform Infrared Spectroscopy, Differential Scanning Calorimetry and Dynamic Mechanical Analyser. Major knowledge and technological gaps in the investigation of the combined effects of mechanical stress, environmental corrosivity and cathodic protection on coating degradation have been identified.

A review of techniques for the monitoring of cathodic shielding and corrosion under disbonded coatings

The mitigation of external corrosion of energy pipelines by a combination of barrier coatings and Cathodic Protection (CP) is not always effective. Even when design specifications are properly met, the shielding of cathodic protection current from reaching steel surface by disbonded barrier coatings, often referred to as cathodic shielding, may lead to severe corrosion problems such as deep pitting, high and near neutral pH Stress Corrosion Cracking (SCC) and Microbiologically Induced Corrosion (MIC). Unfortunately, current indirect assessment methods used in the pipeline industry have serious difficulties in detecting such corrosion problems. This paper provides a brief review of current techniques and their limitations when being applied under complex buried pipeline environmental conditions. The main purpose is to identify potential methods that could be utilised in the design of new monitoring probes specific for the monitoring of cathodic shielding and corrosion of disbonded coatings in the pipeline industry.