A Bayesian approach to the determination of ignition delay

A novel in-cylinder pressure method for determining ignition delay has been proposed and demonstrated. This method proposes a new Bayesian statistical model to resolve the start of combustion, defined as being the point at which the band-pass in-cylinder pressure deviates from background noise and the combustion resonance begins. Further, it is demonstrated that this method is still accurate in situations where there is noise present. The start of combustion can be resolved for each cycle without the need for ad hoc methods such as cycle averaging. Therefore, this method allows for analysis of consecutive cycles and inter-cycle variability studies. Ignition delay obtained by this method and by the net rate of heat release have been shown to give good agreement. However, the use of combustion resonance to determine the start of combustion is preferable over the net rate of heat release method because it does not rely on knowledge of heat losses and will still function accurately in the presence of noise. Results for a six-cylinder turbo-charged common-rail diesel engine run with neat diesel fuel at full, three quarters and half load have been presented. Under these conditions the ignition delay was shown to increase as the load was decreased with a significant increase in ignition delay at half load, when compared with three quarter and full loads.

Missionaries, music and method - dissemination of tonic sol-fa in Asia-Pacific countries during the nineteenth century

The Tonic Sol-fa method of teaching choral singing and its system of music notation was developed in England by John Curwen and propagated throughout the British Isles as a means of both enhancing Christian worship and achieving social reform. Tonic Sol-fa may be identified as an entirely foreign musical practice introduced to indigenous people in many British colonies and in other overseas countries during the nineteenth century as an instrument of Christian evangelism as well as of European cultural imposition. Nevertheless, indigenous communities were introduced to other aspects of European musical culture including a choral repertoire consisting of four-part hymnody and masterworks by Handel, Bach, Mozart, etc which sometimes resulted in the emergence of a school of indigenous composers writing in Tonic Sol-fa notation and using the tonal harmonic style. The result has been that in several countries-such as South Africa and Fiji for example-Tonic Sol-fa has been so fully assimilated into the ethnic culture that it has been "indigenized" and may now be said to represent a significant exogenous aspect of the musical culture in these countries.

Tonic Sol-fa was most commonly introduced to countries in the Asia-Pacific Region -as in Africa - by Christian missionaries who sought to exploit the attraction of hymns, particularly when sung in four-part harmony, as a means of evangelizing indigenous people who frequently regarded this aspect of missionary activity as a form of "magic". In particular, the Tonic Sol-fa method and notation gained a significant foothold in what were referred to as the South Sea Islands--especially in Fiji where today, the Fijian Hymn Book (1985 edition) is notated exclusively in Tonic Sol-fa. The vast majority of the Fijians are literate in Tonic Sol-fa notation and congregational singing in four parts is the norm in Fijian churches.

This paper will draw on data from nineteenth century journal sources, particularly The Tonic Sol-fa Reporter (1853-1888) and The Musical Herald (1889-1920), and will document the introduction and dissemination of Tonic Sol-fa in several Asia-Pacific countries where, unlike Australia and New Zealand, the indigenous population has maintained its own cultural and demographic predominance. Countries to be considered will include India, China (including Hong Kong), and Pacific Island nations. There will also be a consideration of the contemporary usage and applications of Tonic Sol-fa in the region, with specific reference to Fiji. It will be argued that countries where Tonic Sol-fa notation has become the norm should resist any external pressure to transfer to the standard staff notation merely for the sake of conformity. In the case of Fiji, almost universal music literacy has been achieved through Tonic Sol-fa and this should be recognized as an enviable social and cultural asset.

Contact pressure and wear in sheet metal forming - an FEM analysis

Wear is the principal cause of tool failure in most sheet metal forming processes. It is well known that the contact pressure between the blank and the tool has a large influence on the wear of the tool, and hence the tool life. This investigation utilises the finite element method to analyse the contact pressure distribution over the die radius for a particular deep drawing process. Furthermore, the evolution of the predicted contact pressure distribution throughout the entire stroke of the punch is also examined. It was found that the majority of the process shows a steady state pressure distribution, with two characteristic peaks over the die radius, at the beginning and end of the sheet contact area. Interestingly, the initial transient contact pressure response showed extremely high localised peak pressures; more than twice that of the steady state peaks. Results are compared to wear reported in the literature, during similar experimental deep drawing processes. Finally, the significance and effect of the results on wear and wear-testing techniques are discussed.

A longitudinal study of economic pressure among people living with a progressive neurological illness

Objectives: Previous research has examined costs associated with progressive neurological illnesses, but has not examined predictors of economic pressure, or quality of life (QOL). The aim of the current study was to examine the predictors of both economic pressure and QOL among people with a range of progressive neurological illness.

Method: Participants were 257 people with motor neurone disease, Huntington’s disease, multiple sclerosis and Parkinson’s.

Results: High levels of cut backs in spending predicted economic pressure for all groups. Economic pressure predicted QOL at 12-month follow-up for all groups except Parkinson’s. For Parkinson’s, predictors of QOL were long duration of illness, illness-related expenses and cut backs in spending. Cut backs in spending, and not income or expenses, were the most important predictor of economic pressure. QOL was predicted by high levels of economic pressure for most of the illness groups.

Discussion: The implications of these findings are discussed. They suggest that cut backs in spending, as opposed to income and expenses, are important factors to focus on assisting people to adjust to the changes to their financial situation that frequently occurs after developing one of these progressive neurological illnesses.

Effect of an arginine-containing nutritional supplement on pressure ulcer healing in community spinal patients

Objective: To determine whether or not the use of an arginine-containing nutritional supplement could result in signifi cantly shorter pressure ulcer (PU) healing times in people with spinal cord injuries living in the community, compared with a comparative historical control group. Method: Eighteen spinal-cord-injured patients (all part of a hospital spinal outreach service) received 9g of a commercial powdered arginine supplement per day until full PU healing occurred. Healing rates were compared against 17 historical control patients (as assessed by medical history audit). 
Results: Baseline characteristics (age, gender, injury level and time) were similar between groups. Mean ulcer healing times were 10.5 ± 1.3 weeks versus 21 ± 3.7 weeks (p<0.05) in the intervention and control groups respectively. Comparison of healing rates in the intervention group against expected healing rates derived from the medical literature showed that intervention patients had a signifi cantly shorter mean healing time (category 2 PU: 5.5±1.3 weeks versus 13.4 weeks; category 3 PU: 12.5 ± 1.9 weeks versus 18.2 weeks; category 4 PU: 14.4 ± 4.8 weeks versus 22.1 weeks). A diagnosis of diabetes did not significantly alter healing rates in either group. Conclusion: Results from this observational study show a promising benefit of arginine supplementation on PU healing for individuals with spinal cord injury living in the community.

Sliding distance, contact pressure and wear in sheet metal stamping

This paper directly examines the contact sliding distance experienced during a typical sheet metal stamping process-an area that has largely been neglected in the literature. A method to numerically quantify the sliding distance is proposed. The sliding distance predicted from this method, and the contact pressure obtained from numerical simulation, allow the recently identified time-dependent contact conditions on the die and blank surfaces to be completely characterized. Consequently, a new insight into the wear/galling that occurs at the die radius in sheet metal stamping is gained. The results show that the region close to zero degrees on the die radius is likely to experience the most wear, with the identified transient stage contributing to a large proportion of the total wear. Additionally, the region on the blank surface often observed to be heavily burnished - the die impact line - is estimated to experience the highest wear severity due to the transient contact conditions. The proposed method to numerically quantify the sliding contact conditions can be applied as a general approach to study any other two-body sliding contact situations.

The effect of different doses of an arginine-containing supplement on the healing of pressure ulcers

Objective: To investigate if a lower dose of arginine in the form of an oral nutritional supplement can show similar benefit in the healing rate of pressure ulcers compared with the current evidence for 9g of arginine.

Method: Twenty-three inpatients with category II, III or IV pressure ulcers were randomised to receive daily, for 3 weeks, the standard hospital diet plus 4.5 or 9g arginine in the form of a commercial supplement. Pressure ulcer size and severity was measured weekly (by PUSH tool; pressure ulcer scale for healing; 0= completely healed, 17= greatest severity). Nutritional status was determined by Subjective Global Assessment.

Results: There were no significant differences in patients’ age, gender, BMI, haemoglobin levels, albumin levels and diagnosis of diabetes between treatment groups. There was a significant decrease in pressure ulcer severity over time (p < 0.001), with no evidence of a difference in healing rate between the two arginine dosages (p=0.991). Based on expected healing time, patients in both treatment groups were estimated to achieve an almost 2-fold improvement compared with the historical control group. Patients categorised as malnourished showed clinically significant impaired healing rates compared with wellnourished patients (p=0.057), although this was unaffected by arginine dosage (p=0.727).

Conclusion: Similar clinical benefits in healing of pressure ulcers can be achieved with a lower dosage of arginine, which can translate into improved concordance and significant cost-savings for both the health-care facilities and for patients.

Bearing e.g. connecting rod bearing, mounting method for reciprocating piston engine of motor vehicle, involves fixedly connecting bearing housing parts by welding process, where welding of parts is performed in defined external region

The method involves dividing a bearing housing into bearing housing parts (4A, 4B) by fracture-splitting. Bearing half-shells (5) are inserted into the parts. The parts are combined to a bearing that encloses a shaft, and are fixedly connected with each other by a welding process such as resistance welding, ultrasonic welding or cold pressure welding process. The welding of the parts is performed in a defined external region. An insulation material is applied between the half-shells and/or the shaft and the housing parts before welding. The parts are pressed on each other during welding.

Vascular occlusion training as an alternate method of gaining muscle

Training whilst under the effects of vascular occlusion has become increasingly popular due to the resultant muscle gain associated with this training technique. However, when exercising with the use of a tourniquet type device, it is possible for the pressure being applied to be inconsistent, due the constantly changing cross sectional area of the limb being occluded. This Paper describes the design of a device capable of causing vascular occlusion, but also being able to maintain a stable pressure required to create the blood flow restriction, this being able to be utilized in a sports science environment

Very high pressure liquid chromatography using fully porous particles: Quantitative analysis of fast gradient separations without post-run times

Using a column packed with fully porous particles, four methods for controlling the flow rates at which gradient elution runs are conducted in very high pressure liquid chromatography (VHPLC) were tested to determine whether reproducible thermal conditions could be achieved, such that subsequent analyses would proceed at nearly the same initial temperature. In VHPLC high flow rates are achieved, producing fast analyses but requiring high inlet pressures. The combination of high flow rates and high inlet pressures generates local heat, leading to temperature changes in the column. Usually in this case a post-run time is input into the analytical method to allow the return of the column temperature to its initial state. An alternative strategy involves operating the column without a post-run equilibration period and maintaining constant temperature variations for subsequent analysis after conducting one or a few separations to bring the column to a reproducible starting temperature. A liquid chromatography instrument equipped with a pressure controller was used to perform constant pressure and constant flow rate VHPLC separations. Six replicate gradient separations of a nine component mixture consisting of acetophenone, propiophenone, butyrophenone, valerophenone, hexanophenone, heptanophenone, octanophenone, benzophenone, and acetanilide dissolved in water/acetonitrile (65:35, v/v) were performed under various experimental conditions: constant flow rate, two sets of constant pressure, and constant pressure operation with a programmed flow rate. The relative standard deviations of the response factors for all the analytes are lower than 5% across the methods. Programming the flow rate to maintain a fairly constant pressure instead of using instrument controlled constant pressure improves the reproducibility of the retention times by a factor of 5, when plotting the chromatograms in time.

Unilateral bicep curl hemodynamics: low-pressure continuous vs high-pressure intermittent blood flow restriction

 Light-load exercise training with blood flow restriction (BFR) increases muscle strength and size. However, the hemodynamics of BFR exercise appear elevated compared with non-BFR exercise. This questions the suitability of BFR in special/clinical populations. Nevertheless, hemodynamics of standard prescription protocols for BFR and traditional heavy-load exercise have not been compared. We investigated the hemodynamics of two common BFR exercise methods and two traditional resistance exercises. Twelve young males completed four unilateral elbow flexion exercise trials in a balanced, randomized crossover design: (a) heavy load [HL; 80% one-repetition maximum (1-RM)]; (b) light load (LL; 20% 1-RM); and two other light-load trials with BFR applied (c) continuously at 80% resting systolic blood pressure (BFR-C) or (d) intermittently at 130% resting systolic blood pressure (BFR-I). Hemodynamics were measured at baseline, during exercise, and for 60-min post-exercise. Exercising heart rate, blood pressure, cardiac output, and rate–pressure product were significantly greater for HL and BFR-I compared with LL. The magnitude of hemodynamic stress for BFR-C was between that of HL and LL. These data show reduced hemodynamics for continuous low-pressure BFR exercise compared with intermittent high-pressure BFR in young healthy populations. BFR remains a potentially viable method to improve muscle mass and strength in special/clinical populations.

Real-time measurement of phloem turgor pressure in Hevea brasiliensis with a modified cell pressure probe

Background: Although the pressure flow theory is widely accepted for the transport of photoassimilates in phloem sieve elements, it still requires strong experimental validation. One reason for that is the lack of a precise method for measuring the real-time phloem turgor pressure from the sink tissues, especially in tree trunks. Results: Taking the merits of Hevea brasiliensis, a novel phloem turgor pressure probe based on the state of the art cell pressure probe was developed. Our field measurements showed that the phloem turgor pressure probe can sensitively measure the real-time variation of phloem turgor pressure in H. brasiliensis but the calculation of phloem turgor pressure with xylem tension, xylem sap osmotic potential and phloem sap osmotic potential will under-estimate it. The measured phloem turgor pressure gradient in H. brasiliensis is contrary to the Münch theory. The phloem turgor pressure of H. brasiliensis varied from 8-12 bar as a consequence of water withdrawal from transpiration. Tapping could result in a sharp decrease of phloem turgor pressure followed by a recovery from 8-45 min after the tapping. The recovery of phloem turgor pressure after tapping and its change with xylem sap flow suggest the importance of phloem water relationship in the phloem turgor pressure regulation. Conclusion: The phloem turgor pressure probe is a reliable technique for measuring the real-time variation of phloem turgor pressures in H. brasiliensis. The technique could probably be extended to the accurate measurement of phloem turgor pressure in other woody plants which is essential to test the Münch theory and to investigate the phloem water relationship and turgor pressure regulation. © 2014 An et al.

Estimation of accumulated lethality under pressure-assisted thermal processing

A study was conducted to develop an integrated process lethality model for pressure-assisted thermal processing (PATP) taking into consideration the lethal contribution of both pressure and heat on spore inactivation. Assuming that the momentary inactivation rate was dependent on the survival ratio and momentary pressure-thermal history, a differential equation was formulated and numerically solved using the Runge-Kutta method. Published data on combined pressure-heat inactivation of Bacillus amyloliquefaciens spores were used to obtain model kinetic parameters that considered both pressure and thermal effects. The model was experimentally validated under several process scenarios using a pilot-scale high-pressure food processor. Using first-order kinetics in the model resulted in the overestimation of log reduction compared to the experimental values. When the n th-order kinetics was used, the computed accumulated lethality and the log reduction values were found to be in reasonable agreement with the experimental data. Within the experimental conditions studied, spatial variation in process temperature resulted up to 3.5 log variation in survivors between the top and bottom of the carrier basket. The predicted log reduction of B. amyloliquefaciens spores in deionized water and carrot purée had satisfactory accuracy (1.07-1.12) and regression coefficients (0.83-0.92). The model was also able to predict log reductions obtained during a double-pulse treatment conducted using a pilot-scale high-pressure processor. The developed model can be a useful tool to examine the effect of combined pressure-thermal treatment on bacterial spore lethality and assess PATP microbial safety. © 2013 Springer Science+Business Media New York.

Trench stability under bentonite pressure in purely cohesive clay

Trench stability is a conventional geotechnical problem; however, current evaluations are often based entirely on empiricism. This paper uses numerical finite-element upper and lower bound limit analysis to produce stability charts for two-dimensional and three-dimensional homogeneous and inhomogeneous undrained diaphragm wall trenches. Using the limit theorems cannot only provide a simple and useful way of analyzing the stability of the trench, but also avoid the shortcomings and arbitrary assumptions underpinning the limit equilibrium method. By considering the effects from the bentonite slurry pressures, the collapse load in this study has been bracketed to within ±8.5 or better by the numerical upper and lower bound limit analyses. The chart solutions can be used to predict either the critical depth or the safety factor of the trench and provide a convenient tool for preliminary designs by practicing engineers. © 2014 American Society of Civil Engineers.