A substantially visibly transparent topical physical sunscreen formulation

A topically applied sunscreen composition is provided, which by use of nano-sized particles of a physical UV screening agent in a dermatologically acceptable carrier, provides a dermatologically acceptable level of SPF and broad-spectrum protection from UVA and UVB radiation without the need to include chemical UV screening agents in the composition.

Fabrication of ultrafine powder from eri silk through attritor and jet milling

Fibroin protein derived from silk fibres has been extensively studied with exciting outcomes for a number of potential advanced biomaterial applications. However, one of the major challenges in applications lies in engineering fibroin into a  desired form using a convenient production technology. In this paper, fabrication of ultrafine powder from eri silk is reported. The silk cocoons were degummed and the extracted silk fibres were then chopped into snippets prior to attritor and air jet milling. Effects of process control agents, material load and material to water ratio during attritor milling were studied. Compared to dry and dry–wet attritor milling, wet process emerged as the preferred option as it caused less colour change and facilitated easy handling. Ultrafine silk powder with a volume based particle size d(0.5) of around 700 nm could be prepared following the sequence of chopping ➔ wet attritor milling ➔ spray drying ➔ air jet milling. Unlike most reported powder production methods, this method could fabricate silk particles in a short time without any pre-treatment on degummed fibre. Moreover, the size range obtained is much smaller than that previously produced using standard milling devices. Reduction in fibre tenacity either shortened the milling time even further or helped bypassing media milling to produce fine powder directly through jet milling. However, such reduction in fibre strength did not help in increasing the ultimate particle fineness. The study also revealed that particle density and particle morphology could be manipulated through appropriate changes in the degumming process.

Graphical Abstract:  Fabrication of eri silk powder using attritor and jet milling is reported. Volume based particle size d(0.5) of around 700 nm could be prepared following the sequence chopping ➔ wet attritor milling ➔ spray drying ➔ air jet milling. No pre-treatments were used and the particle size range obtained is much smaller than that previously produced using standard milling devices. Particle density morphology could be manipulated through appropriate changes of cocoon degumming conditions.

Novel metal structures through powder metallurgy for biomedical applications

Biocompatible porous Ti-16Sn-4Nb alloys were synthesised in quest of a novel tissue engineering biomaterial for bone regeneration. The alloys were prepared from elemental powders via mechanical alloying followed by space-holder sintering. The effects of ball milling variables on the characteristics and mechanical properties of bulk and porous Ti-16Sn-4Nb alloy have been investigated.

Porous Ti-Nb-Zr alloy through powder metallurgy for biomedical applications

This work investigated the structure and properties relationship, surface modification, biocompatibility and bioactivity of a porous Ti-Nb-Zr alloy. The porous alloy exhibited inter-connected porous structure, good biocompatibility and high mechanical strength with an elastic modulus close to that of bone. Porous Ti-Nb-Zr alloys are thus promising biomaterials for hard tissue replacement.

Characterization and sorption ability of wool powder

This work focused on the characterisation of wool powders and their sorption capacity for dyes and metal ions. It provides new information to the field of wool and the potential use of wool to sorb contaminants from wastewater. It also suggests a new use for inferior and waste wool.

Fabricating and characterising silk powder for biomedical and sorption applications

This research developed a milling technology for ultrafine silk particles and designed novel biocompatible and biodegradable silk composites for repairing hard tissue defects. It also demonstrated high and rapid reversible ion binding properties of silk particles and thereby opened up their application opportunities as advanced green sorbents.

Silk powder for regenerative medicine

Two approaches are used for silk particle production: bottom up and top down. In the bottom up approach, different liquid-solid phase transfer techniques are adapted to fabricate particles from silk solution. In the top down approach, silk fibres are milled by various means to prepare ultrafine silk particles. Many important properties of particles such as size, geometry, porosity, stability and biodegradability are dependent on the specific methods of particle production. These properties influence drug loading and release, delivery modes, biocompatibility and their clearance from the body. Particle properties also determine biomechanical properties of particle reinforced composite scaffolds. Thus correlation between preparation, characterisation and application of silk particles for a specific biomedical application is critical. Progress made in this direction and challenges ahead are discussed in this chapter. © 2014 Woodhead Publishing Limited. All rights reserved.

Effects of milling time on powder packing characteristics and compressive mechanical properties of sintered Ti-10Nb-3Mo alloy

The influence of milling time on the powder packing characteristics and compressive mechanical properties of a biomedical Ti-10Nb-3Mo alloy (wt.%) was investigated. Ball milling was performed on elemental metal powders at different milling times of 0 (blended), 2, 4, 6, 8, and 10 h. This article demonstrates that despite the beneficial effects of ball milling technique in the mechanical alloying of the Ti-based alloy, the ball-milled powders synthesized at longer milling times can adversely affect the packing density and significantly diminish the compressive mechanical properties of the sintered powders. Crown