Structure and phase stability of NiMnGa ferromagnetic shape memory alloys by experimental and ab-initio techniques

This paper summarizes some of our recent results on crystal structure, microstructure, orientation relationship between martensitic variants and crystallographic features of martensitic transformation in Ni-Mn-Ga FSMAs. It was shown that Ni53Mn25Ga22 has a tetragonal I4/mmm martensitic structure at room temperature. The neighboring martensitic variants in Ni53Mn25Ga22 have a compound twinning relationship with the twinning elements K1={112}, K2={11-2}, η1=<11-1>, η2=<111>, P={1-10} and s=0.379. The ratio of the relative amounts of twins within the same initial austenite grain is ~1.70. The main orientation relationship between austenite and martensite is Kurdjumov-Sachs (K-S) relationship. Based on the crystallographic phenomenological theory, the calculated habit plane is {0.690 -0.102 0.716}A (5.95° from {101}A), and the magnitude, direction and shear angle of the macroscopic transformation shear are 0.121, <-0.709 0.105 0.698>A (6.04° from <-101>A) and 6.88°, respectively.

Structural phase transformations of Mg3N2 at high pressure : experimental and theoretical studies

The structural behavior of Mg₃N₂ has been investigated up to 40.7 GPa at room temperature by means of angle-dispersive X-ray diffraction. A reversible, first-order structural phase transition from the ambient cubic phase (Ia3̅) to a high-pressure monoclinic phase (C2/m) is found to start at ~ 20.6 GPa and complete at ~ 32.5 GPa for the first time. The equation of state determined from our experiments yields bulk moduli of 110.7(2) and 171.5(1) GPa for the cubic and monoclinic phases, respectively, indicating higher incompressibility of the high-pressure phase of Mg₃N₂. First-principles calculations reproduced the phase stability and transition pressure determined in our experiment. In addition, a second phase transition from the monoclinic phase to a hexagonal phase (P3̅m₁) was predicted around 67 GPa for Mg₃N₂. The electronic band structures of three phases of Mg₃N₂ are also calculated and discussed.

Phase morphology, thermomechanical, and crystallization behavior of uncompatibilized and PP-g-MAH compatibilized polypropylene/polystyrene blends

In this article, we discuss the phase morphology, thermal, mechanical, and crystallization properties of uncompatibilized and compatibilized polypropylene/polystyrene (PP/PS) blends. It is observed that the Young's modulus increases, but other mechanical properties such as tensile strength, flexural strength, elongation at break, and impact strength decrease by blending PS to PP. The tensile strength and Young's modulus of PP/PS blends were compared with various theoretical models. The thermal stability, melting, and crystallization temperatures and percentage crystallinity of semicrystalline PP in the blends were marginally decreased by the addition of amorphous PS. The presence of maleic anhydride-grafted polypropylene (compatibilizer) increases the phase stability of 90/10 and 80/20 blends by preventing the coalescence. Hence, finer and more uniform droplets of PS dispersed phases are observed. The compatibilizer induced some improvement in impact strength for the blends with PP matrix phase, however fluctuations in modulus, strength and ductility were observed with respect to the uncompatibilized blend. The thermal stability was not much affected by the addition of the compatibilizer for the PP rich blends but shows some decrease in the thermal stability of the blends, where PS forms the matrix. On the other hand, the % crystallinity was increased by the addition of compatibilizer, irrespective of the blend concentration.

Comparative study of the microstructures and mechanical properties of direct laser fabricated and arc-melted AlxCoCrFeNi high entropy alloys

High entropy alloys (HEA) are a relatively new metal alloy system that have promising potential in high temperature applications. These multi-component alloys are typically produced by arc-melting, requiring several remelts to achieve chemical homogeneity. Direct laser fabrication (DLF) is a rapid prototyping technique, which produces complex components from alloy powder by selectively melting micron-sized powder in successive layers. However, studies of the fabrication of complex alloys from simple elemental powder blends are sparse. In this study, DLF was employed to fabricate bulk samples of three alloys based on the AlxCoCrFeNi HEA system, where x was 0.3, 0.6 and 0.85M fraction of Al. This produced FCC, FCC/BCC and BCC crystal structures, respectively. Corresponding alloys were also produced by arc-melting, and all microstructures were characterised and compared longitudinal and transverse to the build/solidification direction by x-ray diffraction, glow discharge optical emission spectroscopy and scanning electron microscopy (EDX and EBSD). Strong similarities were observed between the single phase FCC and BCC alloys produced by both techniques, however the FCC/BCC structures differed significantly. This has been attributed to a difference in the solidification rate and thermal gradient in the melt pool between the two different techniques. Room temperature compression testing showed very similar mechanical behaviour and properties for the two different processing routes. DLF was concluded to be a successful technique to manufacture bulk HEA[U+05F3]s.

Influence of field position and phase of play on the physical demands of match-play in professional rugby league forwards

This article describes the utilisation of an unsupervised machine learning technique and statistical approaches (e.g., the Kolmogorov-Smirnov test) that assist cycling experts in the crucial decision-making processes for athlete selection, training, and strategic planning in the track cycling Omnium. The Omnium is a multi-event competition that will be included in the summer Olympic Games for the first time in 2012. Presently, selectors and cycling coaches make decisions based on experience and intuition. They rarely have access to objective data. We analysed both the old five-event (first raced internationally in 2007) and new six-event (first raced internationally in 2011) Omniums and found that the addition of the elimination race component to the Omnium has, contrary to expectations, not favoured track endurance riders. We analysed the Omnium data and also determined the inter-relationships between different individual events as well as between those events and the final standings of riders. In further analysis, we found that there is no maximum ranking (poorest performance) in each individual event that riders can afford whilst still winning a medal. We also found the required times for riders to finish the timed components that are necessary for medal winning. The results of this study consider the scoring system of the Omnium and inform decision-making toward successful participation in future major Omnium competitions.

An organic ionic plastic crystal electrolyte for rate capability and stability of ambient temperature lithium batteries

Reliable, safe and high performance solid electrolytes are a critical step in the advancement of high energy density secondary batteries. In the present work we demonstrate a novel solid electrolyte based on the organic ionic plastic crystal (OIPC) triisobutyl(methyl)phosphonium bis(fluorosulfonyl)imide (P1444FSI). With the addition of 4 mol% LiFSI, the OIPC shows a high conductivity of 0.26 mS cm-1 at 22 °C. The ion transport mechanisms have been rationalized by compiling thermal phase behaviour and crystal structure information obtained by variable temperature synchrotron X-ray diffraction. With a large electrochemical window (ca. 6 V) and importantly, the formation of a stable and highly conductive solid electrolyte interphase (SEI), we were able to cycle lithium cells (LiLiFePO4) at 30 °C and 20 °C at rates of up to 1 C with good capacity retention. At the 0.1 C rate, about 160 mA h g-1 discharge capacity was achieved at 20 °C, which is the highest for OIPC based cells to date. It is anticipated that these small phosphonium cation and [FSI] anion based OIPCs will show increasing significance in the field of solid electrolytes.

Tristearin bilayers: structure of the aqueous interface and stability in the presence of surfactants

We report results of atomistic molecular dynamics simulations of an industrially-relevant, exemplar triacylglycerol (TAG), namely tristearin (TS), under aqueous conditions, at different temperatures and in the presence of an anionic surfactant, sodium dodecylbenzene sulphonate (SDBS). We predict the TS bilayers to be stable and in a gel phase at temperatures of 350 K and below. At 370 K the lipid bilayer was able to melt, but does not feature a stable liquid-crystalline phase bilayer at this elevated temperature. We also predict the structural characteristics of TS bilayers in the presence of SDBS molecules under aqueous conditions, where surfactant molecules are found to spontaneously insert into the TS bilayers. We model TS bilayers containing different amounts of SDBS, with the presence of SDBS imparting only a moderate effect on the structure of the system. Our study represents the first step in applying atomistic molecular dynamics simulations to the investigation of TAG-aqueous interfaces. Our results suggest that the CHARMM36 force-field appears suitable for the simulation of such systems, although the phase behaviour of the system may be shifted to lower temperatures than is the case for the actual system. Our findings provide a foundation for further simulation studies of the TS-aqueous interface.

Electrospun poly(vinyl alcohol)/phase change material fibers: morphology, heat properties, and stability

A phase change material (PCM) from a mixture of plant oils was incorporated into electrospun poly(vinyl alcohol) (PVA) nanofibers using an emulsion electrospinning technique. Effects of PCM and PVA content in the emulsions on nanofiber morphology, heat properties, and phase change stability were examined. Higher PCM loadings in the nanofibers led to increased fiber diameter, gouged fiber surfaces, and higher heat enthalpies. The fibers maintained their morphological integrity even if the PCM melted. They showed reliable heat-regulating performance which can undergo at least 100 cycles of phase change. Such PCM fibers may be used for the development of thermoregulating fabrics or in passive heat storage devices.

Slope stability analysis using Phase 2

Analysing the rock slope stability is a classical problem for geotechnicalengineers. Recently, Hoek-Brown failure criterion has drawn more and more attentionfor rock slope stability assessments. It would be due to the fact that the nonlinearity ismore pronounced at the low confining stresses that are operational in slope stabilityproblems. However, it is still not popular yet. Therefore, in this study, slope stabilityanalyses will be performed based on the generalised Hoek-Brown failure criterionusing a commercial software, Phase 2. The Hoek-Brown strength parameters will beused as direct inputs in numerical simulations. In addition, two rock slope cases willbe investigated. It is expected that better understandings of rock slope mechanisms canbe obtained.

Investigation into the temporal stability of aqueous standard solutions of psilocin and psilocybin using high performance liquid chromatography

This paper reports an investigation into the temporal stability of aqueous solutions of psilocin and psilocybin reference drug standards over a period of fourteen days. This study was performed using high performance liquid chromatography utilising a (955% vlv) methanol: 10 mM ammonium formate,
pH 3.5 mobile phase and absorption detection at 269 nm. It was found that the exclusion of light significantly prolonged the useful life of standards, with aqueous solutions of both psilocin and psilocybin being stable over a period of seven days.

The determination of the local conditions for void initiation in front of a crack tip for materials with second-phase particles

A procedure is proposed to determine, for second-phase particles near a crack tip, the maximum particle stresses at the moment of void initiation by either particle fracture or particle/matrix interface separation. A digital image analysis system is applied to perform a quantitative analysis of corresponding fracture surface regions from stereo image pairs taken in the scanning electron microscope. The fracture surface analysis is used to measure, for individual particles, the crack tip opening displacement at the moment of void initiation and the particle location with respect to the crack tip. From these data, the stress tensor at the moment of void initiation is calculated from the Hutchinson–Rice–Rosengren (HRR) field theory. The corresponding average local stresses within the particle are evaluated by a non-linear Mori–Tanaka-type approach. These stresses are compared to estimates according to the models by Argon et al. [A.S. Argon, J. Im, R. Safoglu, Metall. Trans. 6 (1975) 825] and Beremin [F.M. Beremin, Metall. Trans. 12 (1981) 723]. The procedure is demonstrated on an Al6061–10% Al2O3 metal matrix composite.

Phase formation and physical properties of mechanically alloyed amorphous 55Mg35Ni1OSi

Amorphous 55Mg35Ni10Si alloy powder has been synthesized by mechanical alloying technique using pure Mg, Ni and Si elemental powders. The transformation of the crystalline powders into an amorphous one has been investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and differential scanning calorimetry. The new material produced has a higher thermal stability than reported results, which is beneficial to the fabrication of Mg–Ni–Si bulk amorphous components through powder metallurgy.

Examination of the "all hazards" approach to disaster management as applied to field disaster management and pre-hospital care in Australia

Disasters, emergencies, incidents, and major incidents - they all come back to the same thing regardless of what they are called. The common denominator is that there is loss of life, injury to people and animals and damage and destruction of property. The management of such events relies on four phases: 1. Prevention 2. Preparation 3. Response 4. Recovery Each of these phases is managed in a different way and often by different teams. Here, concentration has been given to phases 2 and 3, with particular emphasis on phase 3, Response. The words used to describe such events are often related to legislation. The terminology is detailed later. However, whatever the description, whenever prevention is not possible, or fails, then the need is to respond. Response is always better when the responders are prepared. Training is a major part of response preparation and this book is designed to assist those in the health industry who need to be ready when something happens. One of the training packages for responders is the Major Incident Medical Management and Support (MIMMS) Course and this work was designed to supplement the manual prepared by Hodgetts and Macway-Jones(87) in the UK. Included is what the health services responder, who may be sent to an event in which the main concern is trauma, should know. Concentration is on the initial response and does not deal in any detail with hospital reaction, the public health aspects, or the mental health support that provides psychological help to victims and responders, and which are also essential parts of disaster management. People, in times of disaster, have always been quick to offer assistance. It is now well recognised however, that the 'enthusiastic amateur', whilst being a well meaning volunteer, isn't always what is needed. All too often such people have made things worse and have sometimes ended up as victims themselves. There is a place now for volunteers and there probably always will be. The big difference is that these people must be well informed, well trained and well practiced if they are to be effective. Fortunately such people and organisations do exist. Without the work of the St John Ambulance, the State Emergency Service, the Rural Fire Service the Red Cross and the Volunteer Rescue Association, to mention only a few, our response to disasters would be far less effective. There is a strong history of individuals being available to help the community in times of crisis. Mostly these people were volunteers but there has also always been the need for a core of professional support. In the recent past, professional support mechanisms have been developed from lessons learned, particularly to situations that need a rapid and well organised response. As lessons are learned from an analysis of events, philosophy and methods have changed. Our present system is not perfect and perhaps never will be. The need for an 'all-hazards approach' makes detailed planning very difficult and so there will probably always be criticisms about the way an event was handled. Hindsight is a wonderful thing, provided we learn from it. That means that this text is certainly not the 'last word' and revisions as we learn from experience will be inevitable. Because the author works primarily in New South Wales, many of the explanations and examples are specific to that state. In Australia disaster response is a State, rather than a Commonwealth, responsibility and consequently, and inevitably, there are differences in management between the states and territories within Australia. With the influence of Emergency Management Australia, these differences are being reduced. This means that across state and territory boundaries, assistance is common and interstate teams can be deployed and assimilated into the response rapidly, safely, effectively and with minimum explanation. This text sets out to increase the understanding of what is required, what is in place and how the processes of response are managed. By way of introduction and background, examples are given of those situations that have occurred, or could happen. Man Made Disasters has been divided into two distinct sections. Those which are related to structures or transport and those related directly to people. The first section, Chapter 3, includes: • Transport accidents involving land, rail, sea or air vehicles. • Collapse of buildings for reasons other than earthquakes or storms. • Industrial accidents, including the release of hazardous substances and nuclear events. A second section dealing with the consequences of the direct actions of people is separated as Chapter 4, entitled 'People Disasters'. Included are: • Crowd incidents involving sports and entertainment venues. • Terrorism From Chapter 4 on, the emphasis is on the Response phase and deals with organisation and response techniques in detail. Finally there is a section on terminology and abbreviations. An appendix details a typical disaster pack content. War, the greatest of all man made disasters is not considered in this text.

Austenite stability in Fe-Mn-Si-based shape memory alloys

The stability of austenite in a number of Fe–Mn–Si-based shape memory alloys has been investigated. It was found that a grain boundary precipitate of BCC structure is formed over a wide range of alloy compositions and heat treatment temperatures. This grain boundary phase has been identified as the chi (χ) phase. Although up to 3 vol.% of the grain boundary precipitate was generated by isothermal aging in the range 500–800 °C, it was found not to markedly affect the mechanical properties or the shape memory effect. Nano-indentation indicated that the hardness and strength of the parent and precipitate phase are very similar, as are their compositions.