Experimental study of the degradation of volatile organic compounds by photocatalytic oxidation using TiO2 pellets

A fixed bed photocatalytic reactor has been designed and built with a UV
radiation source. Ti02 pellets were placed on the three fixed beds within the
reactor. Acetone was used as an indicator of volatile organic compounds (VOCs) during the experiment. Under the flow rate of 12.75 l/min, the oxidation efficiencies were obtained at four different concentrations of acetone laden gas streams ranged from 40ppm to 250ppm. It was found that the lower the acetone concentration of the untreated inlet gas, the higher the oxidation efficiency; the obtained oxidation efficiency was in the range of 40-70% for various concentrations of untreated gases.

Photocatalytic degradation of dye effluent by titanium dioxide pillar pellets in aqueous solution

Photocatalytic oxidation (PCO) process is an effective way to deal with organic pollutants in wastewater which could be difficult to be degraded by conventional biological treatment methods. Normally the TiO2 powder in nanometre size range was directly used as photocatalyst for dye degradation in wastewater. However the titanium dioxide powder was arduous to be recovered from the solution after treatment. In this application, a new form of TiO2 (i.e. pillar pellets ranging from 2.5 to 5.3 mm long and with a diameter of 3.7 mm) was used and investigated for photocatalytic degradation of textile dye effluent. A test system was built with a flat plate reactor (FPR) and UV light source (blacklight and solar simulator as light source respectively) for investigating the effectiveness of the new form of TiO2. It was found that the photocatalytic process under this configuration could efficiently remove colours from textile dyeing effluent. Comparing with the TiO2 powder, the pellet was very easy to recovered from the treated solution and can be reused in multiple times without the significant change on the photocatalytic property. The results also showed that to achieve the same photocatalytic performance, the FPR area by pellets was about 91% smaller than required by TiO2 powder. At least TiO2 pellet could be used as an alternative form of photocatalyst in applications for textile effluent treatment process, also other wastewater treatment processes.

Degradation of VOCs by phototcatalytic oxidation reactor using TiO2 pellets

Volatile Organic Compounds (VOCs) are air pollutants that come from burning fossil fuels and industrial emissions. They have potentially adverse health effects being carcinogenic and highly persistent in the environment. The use of photocatalytic oxidation to remove VOCs has the potential to be applied in indoor air quality improvement and industrial emission control. A fixed bed photocatalytic reactor was designed and built. UV black light lamps were installed in the reactor to provide a source of UV radiation. A non-film titania media as pellets were placed on the three fixed beds within the reactor. Toluene and acetone were used as indicators of VOCs during the experiment. With a flow rate of 12.75l/min, the oxidation efficiencies were obtained at four different concentrations of acetone laden gas streams ranging from 40ppm to 250ppm. It was found that the lower the acetone concentration of the untreated inlet gas, the higher the oxidation efficiency. The oxidation efficiency was in the range of 40–70% for various concentrations of untreated gases. Two concentrations of toluene laden gas stream were also tested using the same reactor. The oxidation efficiencies were found as 50% for 120ppm toluene gas and 45% for 300ppm toluene gas. It was found that the times required for toluene to reach oxidization equilibrium have been halved than for acetone gas stream. Other parameters such as flow rate and UV intensity were also altered to see their effects on the oxidation efficiency. A full spectrum scan was carried out using a Bio-rad Infrared spectrometer. It was found that the main components of the treated gas stream from the outlet of the reactor were CO2 and water along with small amount of untreated acetone. The suspected intermediates of aliphatic hydrocarbons and CO were found in very minimal amounts or undetectable. The research experiments supported that the TiO2 pellets can work effectively in a fixed bed photocatalytic reactor and achieve significant oxidation efficiencies for degradation of toluene and acetone as indicators of VOCs.

A comparative study on preparation of TiO2 pellets as photocatalysts based on different precursors

The porous Ti0₂ pellets were prepared based on pigment grade titaina, P25 titania powder and titaniurn(lV) butoxide. The characterization was done with X-Ray diffraction, scanning electron microscopy and BET measurements. The result shows that Ti0₂ pellets by using titaniurn(IV) butoxide with some addictive have the best surface porosity, with specific surface area of 196.9m²/g. For pigment grade titania and P25 titania powder, it is still effective to enhance the surface area after reassembling. The surface area increased from 11.6 to 29.2 m²/g for pigment grade titania and from 50 to 84.4 m²/g for P25 titania powder. Furthermore, it has been investigated on how to optimize and get the highest surface area by controlling the sintering temperature, reaction temperature, pH of solution, and the amount of alcohol and addictive of surfactant during preparation. The experimental photocatalytic degradation of acetone and toluene was performed using titania pellets made from P25 titania powder.

Photocatalytic production of methane and hydrogen through reduction of carbon dioxide with water using titania pellets

This paper presents an experimental study on employing a pellet form of catalyst in photo-reduction of carbon dioxide with water. Water was first absorbed into titania pellets. Highly purified carbon dioxide gas was then discharged into a reactor containing the wet pellets, which were then illuminated continuously for 65 hours using UVC lamps. Analysing the products accumulated in the reactor confirmed that methane and hydrogen were produced through photo-reduction of carbon dioxide with water. No other hydrocarbons were detected. Increasing the temperature in the reactor has showed little change on the amount of methane produced.

Photocatalytic reduction of carbon dioxide into gaseous hydrocarbon using TiO2 pellets

It has been shown that CO₂ could be transformed into hydrocarbons when it is in contact with water vapour and catalysts under UV irradiation. This paper presents an experimental set-up to study the process employing a new approach of heterogeneous photocatalysis using pellet form of catalyst instead of immobilized catalysts on solid substrates. In the experiment, CO₂ mixed with water vapour in saturation state was discharged into a quartz reactor containing porous TiO₂ pellets and illuminated by various UV lamps of different wavelengths for 48 h continuously. The gaseous products extracted were identified using gas chromatography. The results confirmed that CO₂ could be reformed in the presence of water vapour and TiO₂ pellets into CH₄ under continuous UV irradiation at room conditions. It showed that when UVC (253.7 nm) light was used, total yield of methane was approximately 200 ppm which was a fairly good reduction yield as compared to those obtained from the processes using immobilized catalysts through thin-film technique and anchoring method. CO and H₂ were also detected. Switching from UVC to UVA (365 nm) resulted in significant decrease in the product yields. The pellet form of catalyst has been found to be attractive for use in further research on photocatalytic reduction of CO₂.

Production of Australian freshwater crayfish in earthen-based systems using pelleted diets and forage crops as food

Juvenile Cherax destructor (commonly called theyabby) were cultured in earthen-based ponds and tanks for 70–105d, and were fed pellets and/or a forage crop of the perennialwhiteclover, Trifolium repens. Three supplementary feedingstrategies were evaluated. Yabby growth on pellets consistently exceeded (by67–159%) that obtained on clover. Base-line yields for extensiveproduction systems are around 400 kg ha^–1. Thesupplementary addition of T. repens produced yields of 635kg ha^–1 (in ponds) to 1086 kgha^–1 (in tanks). The sequential addition of cut-cloverto tanks stimulated growth to levels approaching those achieved on pellets.Yabbies stocked into ponds at 17 m^–2 and fed 33%protein pellets for 100 d, resulted in a yield of 1117 kgha^–1.Pellet inputs at a rate of 129–249 g m^–2(dry matter) and 38–83 g m^–2 (protein) over70–100 d resulted in acceptable growth and feed utilisationindices. Clover inputs of 534–682 g m–2 (asdry matter) or 84–177 g m^–2 (as protein)produced reasonable growth rates but poor feed utilisation indices. Aconsiderable quantity of the dry matter and protein content of clover waseitherinefficiently utilised or directed into other production pathways. In tanks,clover inputs from 113–296 g m^–2 (drymatter) and 24–54 g m^–2 (protein) weresufficient to maintain high growth rates for 4 weeks, while in ponds, inputs of21 g m^–2 (dry matter) and 4.3 gm^–2 (protein) were sufficient for 3 weeks. During theearly weeks of production no growth advantage was gained by providing pelletstoanimals cultured in forage-based systems. Forage depletion occurred after3–4 weeks and was probably a major growth limiting factor.

Preliminary study on the use of synthetic substrate for juvenile stage production of the yabby, Cherax destructor (Clark) (Decapoda: Parastacidae)

Juvenile Cherax destructor (commonly called the yabby) (mean weight 48.3 mg) were cultured intensively (stocking density 360/m²) under controlled conditions for 48 days. The animals were provided with a combination of food (high protein pellets and/or natural feed organisms attached to a conditioned synthetic substrate) and refuge. Fastest growth and highest yield was recorded when both pellets and the conditioned synthetic material were provided. Although the yabbies sheltered in the synthetic substrate, it did not increase survival. Juvenile yabbies (< 200 mg) were able to graze on small organisms attached to the synthetic material but this ability appeared to decline as the yabbies grew to a larger size. The use of artificial substrates in the intensive nursery phase production of juvenile freshwater crayfish is discussed.

The relative absorption of fatty acids in brown trout (Salmo trutta) fed a commercial extruded pellet coated with different lipid sources

The objective of the present study was to investigate the fatty acid absorption capabilities of brown trout (Salmo trutta) fed commercial extruded diets. Five commercial extruded pellets, different only in the lipid sources used for fat coating, were tested on juvenile brown trout for 45 days. The trout were reared in fresh water at 14.6 ± 0.4° C and 7.7 ±
0.3 mg/l, temperature and dissolved oxygen, respectively. The tested lipid sources were fish oil, canola oil, oleine oil, swine fat and poultry fat. After the adaptation period faeces were collected by gently stripping from naesthetized fish. Fatty acid analysis was performed on experimental diets and on collected faeces to evaluate the relative absorption capabilities of the trout digestive system with respect to each detected fatty acid. The use of the relative absorption efficiency (rAE) was opted to evaluate the intrinsic capability of each fatty acid to be absorbed. Brown trout showed a
specific preferential order of absorption of the fatty acids, preferring shorter over longer chain fatty acids and preferring the more unsaturated to the more saturated fatty acids. The fatty acid that showed the best relative absorbability was the C18:4n-3 (rAE = 5.14 ± 0.72), which has a fairly short carbon chain, but at the same time a high unsaturation level, followed by the C18:3n-3 (rAE = 3.38 ± 0.30). The fatty acid that showed the worst relative absorbability (rAE = 0.21 ± 0.02) was C24:1n-9.

The effects of various binders and moisture content on pellet stability of research diets for freshwater crayfish

Two experiments were conducted to assess the water stability of a practical research diet manufactured with various binders and differing levels of moisture. In the first experiment the binders – agar, gelatine, carrageenan, and carboxymethylcellulose (CMC) were included at both 3 and 5% of total ingredient weight. All binders were tested with equal ingredient weight to water volume, and additionally carrageenan was tested in a diet with double the water volume. The dry matter remaining following immersion for up to 180 min was calculated and the rate of pellet decay was modelled using the Weibull distribution. The analysis revealed that the rate of dry matter loss decreased with time, and that carrageenan and CMC binders were significantly better (P < 0.001) binders than the agar and gelatine. The 5% binder concentration slowed the decay rate by as much as 62% as compared with the 3% binder concentration. The second experiment compared the binding performance of carrageenan and sodium alginate in both 50% moisture and 10% moisture pellets. The same analysis revealed that 10% moisture alginate-bound pellets were more water stable than the others. A discussion of the use of moist diets for crayfish research is included.

Enhanced degradation efficiency of toluene using titania/silica photocatalysis as a regeneration process

Three kinds of titania/silica pellets were prepared using the sol-gel method with surface areas of 50.4m² g-1, 421.1m².g^-1 and 89.1m².g^-1. An annular reactor was designed and built to determine the degradation efficiency of toluene and to investigate the relationship between the adsorption and desorption-photocatalytic processes. Surface area is an important factor influencing the adsorption-photocatalytic efficiency. Higher surface areas of pellets contribute to high rates of conversion of toluene. Un-reacted toluene and reaction intermediates accumulating on their surface deactivated the titania/silica catalyst. To overcome this problem, the adsorption and regeneration process were alternated in a dual reactor system. Connecting or disconnecting the toluene feed gas enabled one reactor to adsorb toluene, while the second reactor was regenerated by photocatalysis. Using UV irradiation and titania/silica pellets with high BET surface area (421.1 m².g^-1), the alternating adsorption/regeneration processes kept the degradation efficiency of toluene at 90% after 8 hours operation. By improving the adsorption-photocatalysis efficiency, and minimising the generation and accumulation of intermediate on the surface of pellets, the method extended catalyst life and maintained a high degradation efficiency of toluene.

Change in the diet of sooty owls (Tyto tenebricosa) since European settlement: from terrestrial to arboreal prey and increased overlap with powerful owls

The current diet of the sooty owl (Tyto tenebricosa) was determined by analysing freshly regurgitated pellets collected beneath their roosting sites in East Gippsland, Victoria. Comparisons were then made with: (i) prehistoric and historic diet from bone deposits found in cave roosts, and (ii) diet of a sympatric owl species, the powerful owl (Ninox strenua). Sooty owls consumed a large array of terrestrial mammal species before European settlement, but only three terrestrial species were detected in their current diet, a reduction of at least eight species since European settlement. To compensate, sooty owls have increased their consumption of arboreal prey from 55% to 81% of their diet. Arboreal species are also a major component of the powerful owl diet and this prey shift by sooty owls has increased dietary overlap between these two species. Predation by foxes (Vulpes vulpes) and other feral species is likely to have reduced the amount of terrestrial prey available to sooty owls since European settlement. Investigation of changes in the diet of sooty owls may offer a unique monitoring system for evaluating the ability of fox-control strategies to influence increases in numbers of critical-weight-range mammals.