Electrospun poly(vinyl alcohol)/phase change material fibers: morphology, heat properties, and stability

A phase change material (PCM) from a mixture of plant oils was incorporated into electrospun poly(vinyl alcohol) (PVA) nanofibers using an emulsion electrospinning technique. Effects of PCM and PVA content in the emulsions on nanofiber morphology, heat properties, and phase change stability were examined. Higher PCM loadings in the nanofibers led to increased fiber diameter, gouged fiber surfaces, and higher heat enthalpies. The fibers maintained their morphological integrity even if the PCM melted. They showed reliable heat-regulating performance which can undergo at least 100 cycles of phase change. Such PCM fibers may be used for the development of thermoregulating fabrics or in passive heat storage devices.

Interpreting Fanger's comfort equation within the adaptive paradigm

This paper reviews the evolution of Fanger's heat balance equation in regard of adaptive opportunities. Heat balance and adaptive response are integrated into one model as two fundamental aspects of human-environment interaction that define thermal comfort perception, rather than being seen as two concepts of alternative comfort paradigms. The paper suggests to extent Fanger's model with a heat storage term in order to account for comfort perception under transient thermal conditions, and to review Fanger's modelling assumptions in order to allow for a greater variety of adaptive response options. In the presented model heat exchange is modulated through adaptation of physiological, environmental and behavioural parameters in the human-environment system defined through Fanger's heat exchange equations. A computational prototype is implemented to determine 'comfortable' values and ranges of the six comfort dimensions alternatively to Fanger's comfort indices. Thereby values of for example 'comfortable' clothing and metabolic rate are results rather than necessary input parameters, which are difficult to determine. This approach allows generating design advice for physical, organisational and social environments based on heat balance calculation in the six-dimensional opportunity space defined through Fanger's comfort equation. A starting point for the development of a dynamic adaptive comfort model is set.

Identification of expressed HSP`s in blacklip abalone (Haliotis rubra Leach) during heat and salinity stresses

Both prokaryotes and eukaryotes express a set of highly conserved proteins in response to external and internal stress. The stressors include tissue trauma,anoxia, heavy metal toxicity, infection, changed salinity, and the mmost characterized, heat shock. The result is an expression of stress proteins or heat shock proteins (HSP's) which lead to protection of protein integrity, and also to tolerance under continued heat stress conditions. The Australian backflip abalone (Haliotis rubra) is found principally in southern coastal water and also in estuarine/bay environments. Esturaine/bay environments have greater fluctuations in environmental conditions, especially those of salinity and water temperature, than they are found along oceanic coasts. Abalone from esturaine/bay and oceanic coastal environments were subjected to either increased temperature (2° C/day for a total of 10°C) or hyposalinity (80% seawater). Esturaine/bay abolone were less affectes than the oceanic animals by temperature increase and also demonstrated the ability to volume regualte 3 h after the initial salinity shock. SDS-PAGE and Western blotting techniques, together with dot blots of total protein, using HSP70 specific antibodies, were used to detect HSP70s in the foot muscle of the animals and indicated an expression of HSP70 in response to heat shock in abalone, but not following hyposalinity shock. RT-PCR yeilded a partial cDNA clone of HSP70 from the foot muscle.

Local total and radiative heat-transfer coefficients during the heat treatment of a workpiece in a fluidised bed

The heat-transfer coefficients around a workpiece immersed in an electrically heated heat treatment fluidised bed were studied. A suspension probe designed to simulate a workpiece of complex geometry was developed to measure local total and radiative heat-transfer coefficients at a high bed temperature. The probe consisted of an energy-storage region separated by insulation from the fluidised bed, except for the measuring surface, and a multi-thermocouple measurement system. Experiments in the fluidised bed were performed for a fluidising medium of 120-mesh alumina, a wide temperature range of 110–1050 °C and a fluidising number range of 1.18–4.24. It was found that the workpiece surface temperature has a more significant effect on heat transfer than the bed temperature. The total heat-transfer coefficient at the upper surface of the workpiece sharply decreased at the start of heating, and then steadily increased as heating progressed, while a sharp decrease became a rapid increase and then a slow increase for the radiative heat-transfer coefficient. A great difference in the heat-transfer coefficients around the workpiece was observed.

Modelling of fabric energy storage systems - a review

Fabric energy storage (FES) systems have gained in popularity in the recent years in response to the demand for energy efficient buildings. The dynamic heat transfer mechanisms of an FES require specialised techniques to predict its thermal performance. This requirement has been one of the barriers to the wider use of FES systems. Based on the research literature, this paper presents a critical review of the published mathematical models of FES systems. The paper discusses the usefulness of these models based on the following criteria: the inputs required; the accuracy of predictions; the ability to link with commercially available simulation software: and the degree of difficulty in using the models. The review found that the currently available mathematical models are either not able to predict the thermal behaviour of a building space with an FES system reliably or the models are too complicated and/or require too much specialised knowledge to make them useful.

Effect of load pattern on solar-boosted heat pump water heater performance

The performance of a solar-boosted heat pump water heater (HPWH) operating under full load and part load conditions was determined in an outdoor experimental study. The system utilised flat unglazed aluminium solar evaporator panels to absorb solar and ambient energy. Absorbed energy was transferred to the water tank by means of the heat pump and a wrap around condenser coil on the outside of the tank. The system COP was found to be in the range of 5–7 under clear daytime conditions and 3–5 under clear night-time conditions. Using part load testing of the HPWH system it was found that concentrating the coils in the lower portion of the tank could increase the efficiency of the condenser coil. It was also shown that there exists a generalised linear relationship that can be used to describe the system COP in terms of the temperature difference between the water in the storage tank and the ambient air.

Seasonal coolth storage system for residential buildings in Australia

Night sky cooling is explored as an alternative to the conventional cooling technologies using fossil fuels. The night sky cooling method is based on the long wave radiation of unglazed collectors to the sky at night. An evaluation of the night sky cooling system is present for a residential building in three cities of Australia, namely Alice Springs, Darwin and Melbourne. The system comprises an unglazed flat plate solar collector integrated with borehole storage. It uses night sky radiation to reduce the temperature of the ground near to the boreholes. The system was simulated with TRNSYS, a transient simulation program. The simulation results for adequately sized systems show that night sky radiation is able to reduce the coolth storage borehole temperature and the proposed system is able to meet the cooling load of the residential building simulated in three locations. Borehole lengths of 270, 318 and 106 m are required for coolth storage with 90, 260 and 14 m2 collector area for heat rejection in Alice Springs, Darwin and Melbourne, respectively. At the 20th simulation year, the proposed system is able to achieve a system cooling coefficient of performance of 2.2 in Alice Springs, and 2.8 in Darwin and Melbourne.

Supplementing cold plasma with heat enables doping and nano-structuring of metal oxides

Nitrogen doped SnO2 polycrystalline nanostructures were produced from commercial SnO powders in a new system that combines a low-temperature plasma with heating. The method has the potential to improve the initial efficiency and the cycling performance of SnO2 anodes in Li-ion batteries. With this system, the temperature of the SnO to SnO2 conversion was lowered from 430 to 320 °C, up to 5 at% of doped nitrogen was detected and a nano-scale polycrystalline structure was observed in the product. Combining heat and low-pressure plasma is a promising approach for the production and treatment of enhanced energy storage materials.