Crystal orientation characterisation of electrodeposited nanocrystalline nickel alloy

The collection contains EBSD maps of annealed nanocrystalline Ni and Ni-Fe alloys. The maps show the variation of crystallographic texture across mesoscale colonies within these alloys.

Seeding of single crystal superalloys--Role of seed melt-back on casting defects

Single crystal seeds of the nickel-base superalloy CMSX-4 have been partially melted in a temperature gradient and then quenched. Small islands of random orientation are observed throughout the melted-back semi-solid. These random orientations appear to be pinched-off secondary dendrite arms, but there is no evidence that they are transported ahead of the dendrite tips to nucleate stray grains during directional solidification.

Theoretical investigation of wear-resistance mechanism of superelastic shape memory alloy NiTi

Recent experimental research indicates that superelastic shape memory alloy nickel–titanium (NiTi) is superior to stainless steel against wear and could be applied in tribological engineering. It is believed that the super wear resistance of shape memory alloys is mainly due to the recovery of the superelastic deformation. Our recent wear study indicates that wear rate is very sensitive to the maximum contact pressure. In the present investigation, which involves applying Hertz contact theory and the finite element method, the wear behaviour of shape memory alloys is examined against that of stainless steels through analyzing the maximum contact pressure and the plastic deformation. Our investigation indicates that the contribution of superelasticity to the high wear resistance of NiTi is directly linked to the low transformation stress and the large recoverable transformation strain. Furthermore, the low Young's modulus of this alloy also plays an important role to reduce the maximum contact pressure and therefore reduce the wear rate. Additionally, the high plastic yield strength of transformed martensite NiTi enhances its wear resistance further.

Nanofretting behaviors of NiTi shape memory alloy

Nanofretting refers to cyclic movements of contact interfaces with the relative displacement amplitude at the nanometer scale, where the contact area and normal load are usually much smaller than those in fretting. Nanofretting widely exists in microelctromechanical systems (MEMS) and may become a key tribological concern besides microwear and adhesion. With a triboindenter, the nanofretting behaviors of a nickel titanium (NiTi) shape memory alloy are studied under various normal loads (1–10 mN) and tangential displacement amplitudes (2–500 nm) by using a spherical diamond tip. Similar to fretting, the nanofretting of NiTi/diamond pair can also be divided into different regimes upon various shapes of tangential force–displacement curves. The dependence of nanofretting regime on the normal load and the displacement amplitude can be summarized in a running condition nanofretting map. However, due to the surface and size effects, nanofretting operates at some different conditions, such as improved mechanical properties of materials at the nanometer scale, small apparent contact area and single-asperity contact behavior. Consequently, different from fretting, nanofretting was found to exhibit several unique behaviors: (i) the maximum tangential force in one cycle is almost unchanged during a nanofretting test, which is different from a fretting test where the maximum tangential force increases rapidly in the first dozens of cycles; (ii) the tangential stiffness in nanofretting is three orders magnitude smaller than that in fretting; (iii) the friction coefficient in nanofretting is much lower than that in fretting in slip regime; (iv) no obvious damage was observed after 50 cycles of nanofretting under a normal load of 10 mN.

TiNi shape memory alloy foams synthesized by spacer sintering and their properties

Titanium (Ti) and nickel (Ni) elemental powders were blened by ball milling and the ball milled powders were employed to fabricate NiNi shape memory alloy (SMA) foams by space sintering. Effect of ball milling time on phase constitutes of the sintered TiNi alloy foams was studied by X-ray diffraction (XRD) analysis.Scanning election microscopy (SEM) was used to characterize the porous structure, and compressive tests were carried out to evaluate the mechanical properties of the foams. Results indicate the porosities of the TiNi alloy foams can be controlled by using the spacer sincering method, and the porosities show a significant effect on the mechanical prperties and shape memory effect (SME).

Titanium–nickel shape memory alloy foams for bone tissue engineering

Titanium–nickel (TiNi) shape memory alloy (SMA) foams with an open-cell porous structure were fabricated by space-holder sintering process and characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. The mechanical properties and shape memory properties of the TiNi foam samples were investigated using compressive test. Results indicate that the plateau stresses and elastic moduli of the foams under compression decrease with the increase of their porosities. The plateau stresses and elastic moduli are measured to be from 1.9 to 38.3 MPa and from 30 to 860 MPa for the TiNi foam samples with porosities ranged from 71% to 87%, respectively. The mechanical properties of the TiNi alloy foams can be tailored to match those of bone. The TiNi alloy foams exhibit shape memory effect (SME), and it is found that the recoverable strain due to SME decreases with the increase of foam porosity.

Design of a new biocompatible ti-based shape memory alloy and its superelastic deformation behaviour

Titanium-nickel (Ti-Ni) shape memory alloys have been widely used for biomedical applications in recent years. However, it is reported that Ni is allergic and possibly carcinogenic for the human body. Therefore, it is desirable to develop new Ni-free Ti-based shape memory alloys for biomedical applications. In the present study, a new Ti-18Nb-5Mo-5Sn (wt.%) alloy, containing only biocompatible alloying elements, was designed with the aid of molecular orbital method and produced by vacuum arc melting. Both β and α″ martensitic phases were found to coexist in the alloy after ice-water quenching, indicating the martensitic transformation. The phase transformation temperatures of the Ti-18Nb-5Mo-5Sn alloy were M_s = 7.3 °C, M_f = −31.0 °C, A_s = 9.9 °C, and A_f = 54.8 °C. Superelasticity was observed in the alloy at a temperature higher than the A_f temperature. A totally recovered strain of 3.5 % was achieved for the newly designed Ti-based shape memory alloy with a pre-strain of 4 %.

Porous shape memory alloy scaffolds for biomedical applications : a review

The interest in using porous shape memory alloy (SMA) scaffolds as implant materials has been growing in recent years due to the combination of their unique mechanical and functional properties, i.e. shape memory effect and superelasticity, low elastic modulus combined with new bone tissue ingrowth ability and vasculariszation. These attractive properties are of great benefit to the healing process for implant applications. This paper reviews current state-of-the art on the processing, porous characteristics and mechanical properties of porous SMAs for biomedical applications, with special focus on the most widely used SMA nickel-titanium (NiTi), including (i) microstructural features, mechanical and functional properties of NiTi SMAs; (ii) main processing methods for the fabrication of porous NiTi SMAs and their mechanical properties and (iii) new-generation Ni-free, biocompatible porous SMA scaffolds.

Comparative study of ni effect on the corrosion behavior of low alloy steels in FGD and acid rain environments

The alloying effect of a small amount of nickel on low alloy steel for application to flue gas desulfurization(FGD) systems was studied. The structural characteristics of the rust layer were investigated by scanning electron microscopy(SEM). The electrochemical properties were examined by means of potentiostatic polarization test, potentiodynamic polarization test, and electrochemical impedance spectroscopy(EIS) in a modified green death solution of 16.9 vol.% H2SO4+0.35 vol.% HC1 at 60°C and an acid rain solution of 6.25 X 10-5 M H2S04+5.5 X 10-3 M NaCl at room temperature. It was found that as the amount of nickel increased, the corrosion rate increased in the modified green death solution, which seemed to result from micro-galvanic corrosion between NiS and alloy matrix. In acid rain solution, the corrosion rate decreased as the amount of nickel increased due to the repulsive force of NiFe204 rust against Cl-ions by electronegativity.