Use of plastic and textile media in polishing primary treated effluent

The majority of on-site sewage management systems in Australia fail to perform to expectations. About 60% to 80% of on-site systems reportedly fail to produce acceptable effluent quality, and there is an increaed concern about the risks associated with public health and environmental pollution. In Victoria, a large proportion of septic tank installations have been reported to discharge highly polluted waste to drains and streams. Users, often considered by regulators as operators, have to bear the costs of upgrade/replacement of their old systems to meet stringent water quality guidelines. Some of the common problems include clogging of the disposal fields due to solids and organic overloading and surfacing of highly polluted effluent. Large land application area is subsequently required for irrigating the effluent and/or installation of upgraded disposal fields.
This paper investigates the effectiveness of various types of textile and plastic media, in polishing primary tank effluent, downstream from a typical two-compartment septic tank system. Results to date show that high biochemical oxygen demand removal rates are achieved from the textile and plastic media (up to 86% and 83% respectively). At these removal levels, the performance of a combined conventional septic tank system and plastic/textile filters is comparable to that of an advanced aerated wastewater treatment system. This approach, subject to further investigation, could provide a less costly upgrade.

Deformation behavior of nanostructured aluminum alloy processed by severe plastic deformation

Microstructure and deformation behavior of the commercial aluminum-based Al7.5%Zn–2.7%Mg–2.3%Cu–0.15%Zr alloy subjected to high pressure torsion (HPT) were studied in the present work. A small grain size less than 100 nm, high level of internal stresses and presence of second phase nanoparticles were revealed by transmission electron microscopy (TEM) and X-ray diffraction (XRD). The nanostructured alloy processed by HPT exhibits tensile strength of 800 MPa and ductility of 20% at optimal temperature-strain rate conditions. Unusual influence of a short pre-annealing on tensile strength and ductility of as-processed alloy is discussed.

Plastic deformation in Zr41 Ti14 Cu12.5 Ni10 Be22.5 bulk metal glass under vickers indenter

Vickers indentation was conducted on an as-cast Zr41Ti14Cu12.5Ni10Be22.5 bulk metal glass (BMG) to study shear band formation using a bonded interface technique. The results indicate that the plastic deformation in the BMG is accommodated by the semi-circular (primary) and radial (secondary) shear bands. The inter-band spacing of the semi-circular shear bands is found to be independent of the applied load. The measured size of the deformation zone is in good agreement with the prediction of the theoretical model proposed by Zhang et al.

Determination of plastic yield stress from spherical indentation slope curve

The indentation slope curve from a spherical indentation on elastic-plastic materials is examined. By comparing it with that of an linear elastic material of the same elastic properties, we found that the start point of plastic yielding for an elastic-plastic material can be easily located from the indentation slope curve. Based on this analysis, a simple but effective method is proposed to measure the plastic yield stress of very small samples from a spherical nano-indentation slope curve.

Effect of structure relaxation on the plastic deformation behaviour in a Zr-based BMG under indenter

Vickers and nano indentations were performed on a structurally relaxed Zr₄₁Ti₁₄Cu_12.5Ni₁₀Be_22.5 bulk metallic glass (BMG), and the evolution of the shear bands in the relaxed BMG was investigated and compared to that in the as-cast alloy. Results indicate that the plastic deformation in the BMG with structure relaxation is accommodated by the semicircular (primary) and radial (secondary) as well as tertiary shear bands. Quantitatively, the shear band density in the relaxed alloy was much lower than that in the as-cast alloy. The annihilation of free volume caused by the annealing was responsible for the embrittlement of the sample with structure relaxation.

Plastic deformation in the annealed Zr41Ti14Cu12.5Ni10Be22.5 bulk metal glass under indenter

Vickers and nanoindentationswere carried out on an annealed Zr₄₁Ti₁₄Cu_12.5Ni₁₀Be_22.5 bulk metallic glass (BMG), and the evolution of the shear bands in the annealed BMG was investigated and compared to that in the as-cast alloy. Results indicate that the plastic deformation in the BMG with the structure relaxation is accommodated by the semicircular (primary) and radial (secondary) as well as tertiary shear bands. Quantitatively, the shear band density in the annealed alloywas much lower than that in the as-cast alloy. The load-displacement curve of nanoindentation test for the annealed alloy exhibited a more flat serrated flow. The annihilation of free volume caused by the annealing was responsible for the embrittlement of the annealed sample.

Plastic deformation in a partially crystallized Zr-based BMG under Vickers indenter

Vickers indentations were carried out on an anneal-introduced partially crystallized Zr₄₁Ti₁₄Cu_12.5 Ni₁₀Be_22.5 bulk metallic glass (BMG), and the evolution of the shear bands in this samplewas investigated and compared to the as-cast, aswell as the structurally relaxed counterparts. The results indicate that the plastic deformation in the partially crystallized BMG was accommodated by the semi-circular (primary) and radial (secondary) shear bands. A full crack or flake that was produced due to the spring back during the load removal was observed. The shear band density in the annealed alloy which was dispersed with crystalliteswas significantly lower than that of the as-cast alloy. The difference of the shear band features among the three kinds of alloy status, i.e., partially crystallized, structurally relaxed and as-cast alloys was discussed in terms of the free volume in the BMGs and the characteristics of nano-composites. It has been demonstrated that the plasticity for the three statuses of alloys queues in the descending order as the as-cast, annealed with partial crystallization, and annealed without crystallization.

Plastic flow properties and microstructural evolution in an ultrafine-grained Al-Mg-Si alloy at elevated temperatures

An AA6082 alloy was subjected to eight passes of equal channel angular pressing at 100 °C, resulting in an ultrafine grain size of 0.2 to 0.4 µm. The tensile deformation behavior of the material was studied over the temperature range of 100 °C to 350 °C and strain rate range of 10¯⁴ to 10¯¹ s¯¹. The evolution of microstructure under tensile deformation was investigated by analyzing both the deformation relief on the specimen surface and the dislocation structure. While extensive microshear banding was found at the lower temperatures of 100 °C to 150 °C, deformation at higher temperatures was characterized by cooperative grain boundary sliding and the development of a bimodal microstructure. Dislocation glide was identified as the main deformation mechanism within coarse grains, whereas no dislocation activity was apparent in the ultrafine grains.

The 'filler-effect' in organic ionic plastic crystals : Enhanced conductivity by the addition of nano-sized TiO2

The addition of nano-sized ceramic particles to the plastic crystal ethyl-methyl pyrrolidinium bis(trifluoromethane sulfonyl)amide (P₁₂TFSA) has been investigated by means of DSC and conductivity. The thermal behaviour of the plastic crystal as a function of filler content suggests that the filler particles decrease the onset temperature of the melting slightly at high loadings, however they do not decrease the crystallinity of the material. Furthermore, the IV → III transition decreases in intensity, indicating that the addition of filler increases the possibility for the crystal to remain in metastable rotator phases also at lower temperatures. The conductivity shows a more than one order of magnitude increase with the addition of filler, with a filler concentration dependence that levels out above ~ 10 wt.% TiO₂.

Rotational and translational mobility of a highly plastic salt : Dimethylpyrrolidinium thiocyanate

Thermal analysis, impedance spectroscopy, NMR and Raman spectroscopy have been used to investigate the plastic crystal dimethylpyrrolidinium thiocyanate in order to gain further insight into the properties of organic ionic plastic crystals. This compound has a solid–solid phase transition at 82 °C, and melts at 122 °C. A step increase in conductivity of about one order of magnitude is observed at the phase transition, followed by a decrease in activation energy for conduction. A large entropy gain occurs at the II → I transition, and ¹H NMR linewidth measurements together with second moment calculations showed that the dimethylpyrrolidinium cation goes from a static state, to full isotropic tumbling. Raman measurements confirm that the cation as well as the anion exhibit increased rotational mobility when entering phase I.

Ab initio calculations, Raman and NMR investigation of the plastic crystal di-methyl pyrrolidinium iodide

Above 110 °C the symmetric di-methyl-pyrrolidinium iodide salt forms a plastic crystal phase of interest in the area of new electrolyte materials. In this study ab initio calculations of this material has been conducted in order to assign the vibrational spectra. Raman spectroscopy measurements on the solid salt as well as on the salt dissolved in different solvents has been performed and these have been compared to the theoretical spectra. Furthermore, Raman spectra as a function of temperature have been recorded to investigate possible changes in inter-ionic interaction and/or structure through the phase transition. 1H NMR linewidth measurements as a function of temperature showed a large decrease in linewidth above 100 °C, attributed here to an increase in mobility in agreement with a previously reported phase transition at ~110 °C.