Architecture and engineering of a supramolecular functional material by manipulating the nano-structure of fiber network

Three-dimensional fiber networks were created from an organogel system consisting mainly of elongated fibrils by using a nonionic surfactant as an additive. The presence of the surfactant molecules manipulates the network structure by enhancing the mismatch nucleation on the growing fiber tips. Both the fiber network structure and the rheological properties of the material can be finely tuned by changing the surfactant concentration, which provides a robust approach to the engineering of supramolecular soft functional materials.

Non-isothermal crystallisation kinetics of self-assembled polyvinylalcohol/silica nano-composite

A novel polyvinylalcohol/silica (PVA/SiO₂) nano-composite is prepared with the self-assembly monolayer (SAM) technique. The SiO₂ nano-particles are homogenously distributed throughout the PVA matrixes as nano-clusters with an average diameter ranged from 15 to 240 nm depending on the SiO₂ contents. Using differential scanning calorimetry (DSC), the non-isothermal crystallisation behaviour and kinetics of the PVA/SiO₂ nano-composites are investigated and compared to those of the pure PVA. There are strong dependences of the degree of crystallinity (X_c), peak crystallisation temperature (T_p), half time of crystallisation (t_1/2), and Ozawa exponent (m) on the SiO₂ content and cooling rate. The crystallisation activation energy (E) calculated with the Kissinger model is markedly lower when a small amount of SiO₂ is added, then gradually increases and finally becomes higher than that of the pure PVA when there is more than 10% SiO₂ in the composite.

Characterization of nano-scale particles in hot-rolled, high strength low alloy steels (HSLA)

The contribution of nano-scale particles observed using Atom Probe Tomography in an increase of yield strength of conventional and advanced HSLA steels was studied. The advanced HSLA steel showed higher yield strength than conventional HSLA steel. There were two types of carbides, which primarily contribute to an increase in yield strength of conventional HSLA steel: (i) coarse TiC with average size of 25±5nm and (ii) fine TiC with average radius of 3±1.2nm. The presence of two types of carbides was found in the microstructure of advanced HSLA steel: (i)
nano-scale Ti0.98Mo0.02C0.6 carbides with average radius of 2.2±0.5nm, and (ii) C19Cr7Mo24 particles with an average radius of 1.5±0.3nm. The contribution of precipitation hardening in the yield strength of advanced HSLA steel due to the nano-scale particles was 174MPa, while this value in the conventional HSLA steel was 128MPa.

Nano- and macro-scale characterisation of the mechanical properties of bovine bone

In the present study, nano- and macro-scale characterisations on the mechanical properties of bovine cortical bones have been performed by using nanoindentation and conventional compressive tests. Nanoindentation results showed that the elastic modulus for the osteons and the interstitial lamellae in the longitude direction were 24.7 ± 2.5 GPa and 30.1 ± 2.4 GPa. As it’s difficult to distinguish osteons from interstitial lamellae in the transverse direction, the average elastic modulus for cortical bovine bone in the transverse direction was 19.8 ± 1.6 GPa. Significant differences were found in the modulus values between different microstructures of bone tissue and in different testing direction. It was found that the elastic modulus of bone bovine material in nano-level was higher than that in macro-level. The elastic modulus and
ultimate stress of large bone samples were 12.5 ± 1.9 GPa and 195 ± 19 MPa respectively from the compression test.

Nano zinc oxide for UV protection of textiles

This paper describes the effect on the fading of dyed polyester fabrics in artificial sunlight, when the Ultra Violet (UV) component of the radiation was blocked by coating the fabric with zinc oxide nanoparticles, dispersed in an acrylic polymer. Zinc oxide is photoactive and generates superoxide and hydroxyl radicals (Reactive Oxygen Species; ROS) when irradiated with UV in the presence of oxygen and water. The results for the four dyes studied show that different dye chromophores interact differently with ROS. Selection of dyes with anti oxidant properties or addition of other anti oxidants may reduce the adverse effects of ROS

Micro- and nano-characterization of membrane materials

The global warming has led to enormous challenges worldwide for a large variety of communities, particularly these associated to water and water treatment industry. Due to increasing scarcity of water resources, the development of new membrane materials and water treatment processes will play an important role in tackling this emerging problem. In this paper, the recent development in characterization of in particular, geometrical parameters of micro- and nano-membrane materials will be reviewed. Membranes with micro- and nano-pores have widely been used for ultrafiltration and nanofiltration. The structure of the pores and the surface of the pores/membranes may be optimized to achieve much improved flow rate in these micro-/nano-channels. Therefore, accurate characterization of porous structures will contribute significantly to the prediction of membrane performance. It will not only provide an insight into the new characterization methods but also the development of novel materials.

Natural rubber nanocomposite reinforced with nano silica

Inorganic nano fillers have demonstrated great potential to enhance the properties of natural rubber (NR). The present article reports the successful development of a NR nanocomposite reinforced with nano silica (SiO2). Its dynamic mechanical properties, thermal aging resistance, and morphology are investigated. The results show that the SiO2 nanoparticles are homogenously distributed throughout the NR matrix in a form of spherical nano-cluster with an average size of 80 nm when the SiO2 content is 4 wt%. With the introduction of SiO2, the thermal resistance and the storage modulus of NR host significantly increase, and the activation energy of relaxation of the nanocomposite, compared to the raw NR, increases from 90.1 to 125.8 kJ/mol.

Electroless synthesis of nano-structured gold particles using conducting polymer nanoparticles

In this study, gold nanoparticles were synthesized by electroless recovery of [AuCl4]− from an acidic aqueous solution using nano-structured conducting polymer, polypyrrole nanoparticles, as active surface. The formation of gold nanoparticles was confirmed by TEM, SEM and EDX measurements. The effects of the initial Au(III) concentration on the gold uptake was examined. The recovery capability and gold particle morphology prepared from polypyrrole nanoparticle were compared to that from cast PPy film counterpart.

Crystallographic analysis of nano-structured bainitic steels

A 0.79C-1.5Si-1.98Mn-0.98Cr-0.24Mo-1.06Al-1.58Co (wt%) steel was isothermally heat treated at 200 and 350°C bainitic transformation temperatures. The microstructure was consisted of bainitic ferrite lath and retained austenite for both heat treatment conditions. The crystallographic analysis revealed that the bainitic ferrite laths are close to the Nishiyama-Wassermann orientation relationship with their parent austenite. The isothermal bainite transformation temperature has a significant effect on the retained austenite characteristics and the variant selection of the bainitic ferrite laths. In general, a decrease in the isothennal bainite transformation temperature refined the bainitic structure and weakened the variant selection.

Nano related research in fibres and textiles

With the increasing hype surrounding what nanotechnology can actually deliver, research emphasis in this area needs to be placed on how nanotechnology can bring tangible benefits to existing industries and ordinary consumers. This paper gives selected examples of real world applications of nano-structured materials, including nano fibrous and particulate materials. It reviews recent research into nano-structured surface coating of textile substrates for enhanced functionalities, and the development of fine and uniform nanofibres for advanced applications. Emphasis has been placed on relevant research activities in the Centre for Material and Fibre Innovation at Deakin University, Australia. In the nano-structured surface coating area, several examples of enhancing fabric performance and functionality are provided, including silica coating for photochromic textiles, superhydrophobic surface coating and transparent ZnO coating to reduce colour fading of textiles exposed to UV radiation. In the nanofibre area, these activities include: elimination of beaded fibres without increasing the average diameter of the electrospun nanofibres, electrospinning of side-by-side bi-component nanofibres, new insight into the evolution of fibre morphology in electrospinning and the electrospinning technology itself.

Apatite formation on nano-structured titanium and niobium surface

Current orthopaedic biomaterials research mainly focuses on developing implants that could induce controlled, guided and rapid healing. In the present study, the surface morphologies of titanium (Ti) and niobium (Nb) metals were tailored to form nanoporous, nanoplate and nanofibrelike structures through adjustment of the temperature in the alkali treatment. The in vitro bioactivity of these structures was then evaluated by soaking in simulated body fluid (SBF). It was found that the morphology of the modified surface significantly influenced the apatite inducing ability. The Ti surface with a nanofiber-like structure showed better apatite inducing ability, than the nanoporous or nanoplate surface structures. A thick dense apatite layer formed on the Ti surface with nanofiberlike structure after 1 week soaking in SBF. It is expected that the anofibre-like surface could achieve good apatite formation in vivo and subsequently enhance osteoblast cell adhesion and bone formation in vivo.