Energetics of interlimb coordination

While the traditional dependent variables of motor skill learning are accuracy and consistency of movement outcome, there has been increasing interest in aspects of motor performance that are described as reflecting the ‘energetics’ of motor behaviour. One defining characteristic of skilled motor performance is the ability to complete the task with minimum energy expenditure (Sparrow & Newell, 1998). A further consideration is that movements also have costs in terms of cognitive ‘effort’ or ‘energy’. The present project extends previous work on energy expenditure and motor skill learning within a coordination dynamics framework. From the dynamic pattern perspective, a coordination pattern lowest on the 11KB model potential curve (Haken, Kelso & Bunz, 1985) is more stable and least energy is required to maintain pattern stability (Temprado, Zanone, Monno & Laurent, 1999). Two experiments investigated the learning of stable and unstable coordination patterns with high metabolic energy demand. An experimental task was devised by positioning two cycle ergometers side-by-side, placing one foot on each, with the pedals free to move independently at any metronome-paced relative phase, Experiment 1 investigated practice-related changes to oxygen consumption, heart rate, relative phase, reaction time and muscle activation (EMG) as participants practiced anti-phase, in-phase and 90°-phase cycling. Across six practice trials metabolic energy cost reduced and AE and VE of relative phase declined. The trend in the metabolic and reaction time data and percent co-contraction of muscles was for the in-phase cycling to demonstrate the highest values, anti-phase the lowest and 90°-phase cycling in-between. It was found that anti- and in-phase cycling were both kinematically stable but anti-phase coordination revealed significantly lower metabolic energy cost. It was, therefore, postulated that of two equally stable coordination patterns, that associated with lower metabolic energy expenditure would constitute a stronger attractor. Experiment 2 was designed to determine whether a lower or higher energy-demanding coordination pattern was a stronger attractor by scanning the attractor layout at thirty-degree intervals from 0° to 330°. The initial attractor layout revealed that in-phase was most stable and accurate, but the remaining coordination patterns were attracted to the low energy cost anti-phase cycling. In Experiment 2 only 90°- phase cycling was practiced with a post-test attractor layout scan revealing that 90°-phase and its symmetrical partner 270°-phase had become attractors of other coordination patterns. Consistent with Experiment 1, practicing 90°-phase cycling revealed a decline in AE and VE and a reduction in metabolic and cognitive cost. Practicing 90°-phase cycling did not, however, destabilise the in-phase or anti-phase coordination patterns either kinematically or energetically. In summary, the findings suggest that metabolic and mental energy can be considered different representations of a ‘global’ energy expenditure or ‘energetic’ phenomenon underlying human coordination. The hypothesis that preferred coordination patterns emerge as stable, low-energy solutions to the problem of inter-and intra-limb coordination is supported here in showing that the low-energy minimum of coordination dynamics is also an energetic minimum.

Reducing sedentary behaviour and increasing physical activity among 10-year-old children: overview and process evaluation of the 'Switch-Play' intervention

Overweight and obesity has doubled among children in Australia. There is an urgent need to develop primary prevention strategies to prevent current and future unhealthy weight gain. The aims of this paper are to describe a randomized controlled trial (‘Switch-Play’) developed to prevent unhealthy weight gain among 10-year-old children and to report the findings of the process evaluation. Children from three government primary schools were randomized by class to one of four conditions: a behavioural modification group (BM; n = 69); a fundamental motor skills group (FMS; n = 73); a combined BM and FMS group (n = 90); or a control (usual classroom lessons) group (n = 61). Children in the BM group participated in 19 sessions that encouraged them to reduce screen-based behaviours, and identified physical activity alternatives. The FMS group participated in 19 lessons that focused on mastery of six skills: run, throw, dodge, strike, vertical jump and kick. The combined group participated in all the BM and FMS activities. The intervention specialist teacher reported that the children showed high enjoyment and engagement (88% lessons attended) in most aspects of the programme. At-home tasks were completed by 57–62% of the children, and 92% completed the in-class tasks. Two-thirds of the children in the BM group participated in the behavioural contracting to switch off the TV. Most of the children reported high enjoyment of the programmes, and only a small proportion (7–17%) reported difficulties in switching off their nominated TV shows. More than half the children reported reducing their TV viewing; however, less than half reported increasing their physical activity. It was found that most aspects of the intervention arms of the programme were successfully delivered to the majority of children participating in ‘Switch-Play’; that the programmes were delivered as intended; and that the programmes were favourably evaluated by participating children and their parents.

Elastic behaviour in mechanical draw presses

This thesis explores the elastic behaviour of the mechanical double action press and draw die system commonly used to draw sheet metal components in the automotive industry. High process variability in production and excessive time spent in die try-out are significant problems in automotive stamping. It has previously been suggested that the elastic behaviour of the system may contribute to these problems. However, the mechanical principles that cause the press system to affect the forming process have not been documented in detail. Due to a poor understanding of these problems in industry, the elasticity of the press and tools is currently not considered during the die design. The aim of this work was to explore the physical principles of press system elasticity and determine the extent to which it contributes to problems in try-out and production. On the basis of this analysis methods were developed for controlling or accounting for problems during the design process. The application of frictional restraining force to the edges of the blank during forming depends on the distribution and magnitude of the clamping force between the binders surfaces of the draw die. This is an important control parameter for the deep drawing process. It has been demonstrated in this work that the elasticity of the press and draw die can affect clamping force in two ways. The response of the press system, to the forces produced in the press during forming, causes the magnitude of clamping force to change during the stroke. This was demonstrated using measured data from a production press. A simple linear elastic model of the press system was developed to illustrate a definite link between the measured force variation and the elasticity of the press and tools. The simple model was extended into a finite element model of the complete press system, which was used to control a forming simulation. It was demonstrated that stiffness variation within the system could influence the final strains in a drawn part. At the conclusion of this investigation a method is proposed for assessing the sensitivity of a part to clamping force variation in the press during die design. A means of reducing variation in the press through the addition of a simple linear spring element is also discussed. The second part of the work assessed the influence of tool structure on the distribution of frictional restraining forces to the blank. A forming simulation showed that tool stiffness affects the distribution of clamping pressure between the binders. This was also shown to affect the final strains in a drawn part. However, the most significant influence on restraining force was the tendency of the blank to increase in thickness between the binders during forming. Using a finite element approximation of the try-out process it was shown that the structure of the tool would also contribute to the problems currently experienced in try-out where uneven contact pressure distributions are addressed by manually adjusting the tool surfaces. Finally a generalised approach to designing draw die structures was developed. Simple analysis methods were combined with finite element based topology optimisation techniques to develop a set of basic design guidelines. The aim of the guidelines was to produce a structure with uniform stiffness response to a pressure applied at the binder surface. The work concludes with a recommendation for introducing the methods developed in this thesis into the standard production process.

Characterization of the moisture absorption and thermal ageing behaviour of polymeric composite systems using Raman spectroscopy

Advanced polymeric materials and their respective composites are fast becoming one of the world's most frequently used engineering materials. They find application in the manufacture of e.g. boat hulls, high performance motor vehicles, aircraft components and sports goods. Their high specific strength and specific stiffness give them the edge in applications where weight savings are critical, but their long-term durability is often questioned. These materials are susceptible to environmental conditions such as temperature and humidity. There is also a lack of relevant data, due to the long time-scales required for testing. In this study, the Raman technique has been used to monitor the degradation of two composite systems, namely: a rubber toughened vinylester material used in the marine industry and a high temperature bismaleimide/carbon fibre aerospace composite. Preliminary Raman studies show that the toughening rubber particles dispersed in the cured vinylester resin are leached out during hygrothermal ageing. The weight gain during ageing suggests that this leaching process occurs concurrently with the absorption of water molecules. An increase in the degree of cross-linking is observed when bismaleimide/carbon fibre composite is aged at high temperature. This cross- linking tendency decreases with increasing depth within the carbon fibre bundle.

Testing and modelling to obtain material behaviour for crash simulations

The thesis focusses on improving the material behaviour models used in vehicle crash simulations by identifying the mechanical properties most important to crash events, reformulating the material models used in crash simulations, and developing new tests to obtain crash-relevant material.

The behavioural response of Australian fur seals to motor boat noise

Australian fur seals breed on thirteen islands located in the Bass Strait, Australia. Land access to these islands is restricted, minimising human presence but boat access is still permissible with limitations on approach distances. Thirty-two controlled noise exposure experiments were conducted on breeding Australian fur seals to determine their behavioural response to controlled in-air motor boat noise on Kanowna Island (39°10′S, 146°18′E). Our results show there were significant differences in the seals' behaviour at low (64–70 dB) versus high (75–85 dB) sound levels, with seals orientating themselves towards or physically moving away from the louder boat noise at three different sound levels. Furthermore, seals responded more aggressively with one another and were more alert when they heard louder boat noise. Australian fur seals demonstrated plasticity in their vocal responses to boat noise with calls being significantly different between the various sound intensities and barks tending to get faster as the boat noise got louder. These results suggest that Australian fur seals on Kanowna Island show behavioural disturbance to high level boat noise. Consequently, it is recommended that an appropriate level of received boat sound emissions at breeding fur seal colonies be below 74 dB and that these findings be taken into account when evaluating appropriate approach distances and speed limits for boats.

Objectively measured sedentary behaviour and health and development in children and adolescents: systematic review and meta-analysis

Sedentary behaviour has emerged as a unique determinant of health in adults. Studies in children and adolescents have been less consistent. We reviewed the evidence to determine if the total volume and patterns (i.e. breaks and bouts) of objectively measured sedentary behaviour were associated with adverse health outcomes in young people, independent of moderate-intensity to vigorous-intensity physical activity. Four electronic databases (EMBASE MEDLINE, Ovid EMBASE, PubMed and Scopus) were searched (up to 12 November 2015) to retrieve studies among 2- to 18-year-olds, which used cross-sectional, longitudinal or experimental designs, and examined associations with health outcomes (adiposity, cardio-metabolic, fitness, respiratory, bone/musculoskeletal, psychosocial, cognition/academic achievement, gross motor development and other outcomes). Based on 88 eligible observational studies, level of evidence grading and quantitative meta-analyses indicated that there is limited available evidence that the total volume or patterns of sedentary behaviour are associated with health in children and adolescents when accounting for moderate-intensity to vigorous-intensity physical activity or focusing on studies with low risk of bias. Quality evidence from studies with robust designs and methods, objective measures of sitting, examining associations for various health outcomes, is needed to better understand if the overall volume or patterns of sedentary behaviour are independent determinants of health in children and adolescents.