Mechanical behavior of irregular fibers part I : modeling the tensile behavior of linear elastic fibers

Fiber irregularities are inherent to textile fibers, natural fibers in particular. This series of papers examines the impact of fiber irregularity on the mechanical behavior of textile fibers. In the first part, the effect of fiber dimensional irregularities on the tensile behavior of linear elastic fibers is examined, using the finite element method (FEM). Fiber dimensional irregularities are simulated with sine waves of different magnitude and frequency. The results indicate that increasing the level or magnitude of irregularity will decrease the breaking load, breaking elongation and method Young’s modulus of the fiber, while increasing the frequency of irregularity will decrease the breaking load and method Young’s modulus, but the breaking elongation will increase. Fiber dimensional irregularity and the gauge length effect are also simulated in this study.

Mechanical behavior of irregular fibers part II : non-linear tensile behavior

To further our study of the linear tensile behavior of irregular fibers, in this paper we examine the nonlinear tensile behavior of irregular fibers. As before, we simulate the fiber dimensional irregularities with sine waves of different magnitude and frequency, and report results on the tensile behavior and gauge length effect of the simulated fibers.

Mechanical behavior of irregular fibers part III : the flexural buckling behavior

Fiber buckling behavior is associated with fabric-evoked prickle, which affects clothing comfort and aesthetics. In this paper, the flexural buckling behavior of irregular or nonuniform fibers is studied using the finite element method (FEM). Fiber dimensional irregularities are simulated with sine waves of different magnitude, frequency, and initial phase. The critical buckling loads of the simulated fibers are then calculated from the FE model. The results indicate that increasing the level of irregularity will decrease the critical buckling load of fibers, but the effect of the frequency and initial phase of irregularity on fiber buckling behavior is complicated and is affected by fiber diameter and effective length.

Modeling of the mechanical behavior of nanostructured HSLA steels

In the present paper the basic strengthening mechanisms operating in microstructures are discussed with respect to their application in submicron/nano materials. This analysis focuses on these strengthening mechanisms in bcc microstructures, where the effect of grain boundaries is very strong. An experimental study of the influence of the thermomechanical history on the microstructure and dislocation substructure was performed using two different grades of HSLA steels. As a result, a modified version of the Khan–Huang–Liang flow stress model (KHL) was developed and is discussed in the light of results from the present study. Comparison with experimental results showed significant diversity in the refinement and mechanical responses of each steel, due to different activity of strengthening mechanisms and microalloying elements in the microstructure evolution process. The effect of mechanical and microstructural inhomogeneity in severe plastic deformation (SPD) on the deformation induced grain refinement and mechanical properties was also considered.

Cyclic deformation of advanced high-strength steels : mechanical behavior and microstructural analysis

The fatigue properties of multiphase steels are an important consideration in the automotive industry. The different microstructural phases present in these steels can influence the strain life and cyclic stabilized strength of the material due to the way in which these phases accommodate the applied cyclic strain. Fully reversed strain-controlled low-cycle fatigue tests have been used to determine the mechanical fatigue performance of a dual-phase (DP) 590 and transformation-induced plasticity (TRIP) 780 steel, with transmission electron microscopy (TEM) used to examine the deformed microstructures. It is shown that the higher strain life and cyclic stabilized strength of the TRIP steel can be attributed to an increased yield strength. Despite the presence of significant levels of retained austenite in the TRIP steel, both steels exhibited similar cyclic softening behavior at a range of strain amplitudes due to comparable ferrite volume fractions and yielding characteristics. Both steels formed low-energy dislocation structures in the ferrite during cyclic straining.

Synthesis, characterization and analytical modelling of mechanical behavior of a conducting polymer actuator

Electrochemical synthesis of a tri-layer polypyrrole based actuator optimized for performance was reported. The 0.05 M pyrrole and 0.05 M tetrabutylammonium hexaflurophosphate in propylene carbonate (PC) yielded the optimum performance and stability. The force produced ranged from 0.2 to 0.4mN. Cyclic deflection tests on PC based actuators for 3 hours indicated that the displacement decreased by 60%. PC based actuator had a longer operating time, exceeding 3 hours, compared to acetonitrile based actuators. A triple-layer model of the polymer actuator was developed based on the classic bending beam theory by considering strain electrode material. A tri-layer actuator was fabricated [4, 6], by initially sputter coating a PVDF film with approximately 100nm of gold layer, resulting in a conductive film with a surface resistance of 8-10Ω. The PVDF film was about ~145µm thick had an approximate pore size of 45μm. A solution containing 0.05M distilled pyrrole monomer, 0.05M (TBAPF6) and 1% (w/w) distilled water in PC (propylene carbonate) solution was purged with nitrogen for 15 minutes. The continuity between PPy and PVDF. Results predicted by the model were in good agreement with the experimental data.

Mechanical behavior of nano-micro composite core spun yarns

Mechanical Behavior of Nano-crystalline Metallic Thin Films and Multilayers Under Microcompression

Microcompression tests were performed to determine the mechanical behavior of nano-crystalline Cu/Fe and Fe/Cu multilayers, as well as monolithic Cu and Fe thin films. The results show that the micropillars of pure Cu thin film bulge out under large compressive strains without failure, while those of pure Fe thin film crack near the top at low compressive strains followed by shear failure. For Cu/Fe and Fe/Cu multilayers, the Cu layers accommodate the majority of plastic deformation, and the geometry constraints imposed by Fe layers exaggerates the bulging in the Cu layers. However, the existence of ductile Cu layers does not improve the overall ductility of Cu/Fe and Fe/Cu multilayers. Cracking in the Fe layers directly lead to the failure of the multilayer micropillars, although the Cu layers have very good ductility. The results imply that suppressing the cracking of brittle layers is more important than simply adding ductile layers for improving the overall ductility of metallic multilayers.

A study on mechanical behavior of functionally-graded carbon nanotube-reinforced nanocomposites

In this study, we are focusing on the investigation of the effects of gradient patterns on mechanical behavior of functionally-graded carbon nanotube-reinforced nanocomposites and considering typical beams made of such nanocomposites. Both analytic and finite element-based numerical models were developed. Analytic model was developed based on the first-order shear deformation and Timoshenko beam theories meanwhile finite element models were developed using Abaqus in conjunction with user-defined subroutines for defining the continuously gradient material properties for different gradient patterns. Position-dependent elastic modulus equations for four continuously graded patterns were studied. A nongraded pattern was used for benchmarking with the same geometry and total carbon nanotube (CNT) contents. For validation and verification, the results on both deflection and stress of these nanocomposite beams were analyzed, which clearly showed high influence from gradient patterns on these mechanical behaviors of such beams.

The effect of thermomechanical treatment on the microstructure and the mechanical behavior of a supersaturated Cu-Ag alloy

Supersaturated Cu-3at.% Ag alloy was processed by cold rolling and short-time annealing in order to achieve a combination of high strength and good tensile ductility. After annealing of the rolled samples a heterogeneous solute atom distribution was developed due to the dissolution of nanosized Ag particles in some volumes of the matrix. In regions with higher solute content, the high dislocation density formed due to rolling was stabilized, while in other volumes the dislocation density decreased. The heterogeneous microstructure obtained after annealing exhibited a much higher ductility and only a slightly lower strength than in the as-rolled state.

Modeling the tensile behavior of fibers with geometrical and structural irregularities

Virtually all fibers exhibit some dimensional and structural irregularities. These include the conventional textile fibers, the high-performance brittle fibers and even the newly developed nano-fibers. In recent years, we have systematically examined the effect of fiber dimensional irregularities on the mechanical behavior of the irregular fibers. This paper extends our research to include the combined effect of dimensional and structural irregularities, using the finite element method (FEM). The dimensional irregularities are represented by sine waves with a 30 % magnitude of diameter variation while the structural irregularities are represented by longitudinal and horizontal cavities distributed within the fiber structure. The results indicate that fiber geometrical or dimensional variations have a marked influence on the tensile properties of the fiber. It affects not only the values of the breaking load and extension, but also the shape of the load-extension curves. The fiber structural irregularities simulated in this study appear to have little effect on the shape of the load-extension curves.

Effect of deformation schedule on the microstructure and mechanical properties of a thermomechanically processed C-Mn-Si transformation-induced plasticity steel

Thermomechanical processing simulations were performed using a hot-torsion machine, in order to develop a comprehensive understanding of the effect of severe deformation in the recrystallized and nonrecrystallized austenite regions on the microstructural evolution and mechanical properties of the 0.2 wt pct C-1.55 wt pct Mn-1.5 wt pct Si transformation-induced plasticity (TRIP) steel. The deformation schedule affected all constituents (polygonal ferrite, bainite in different morphologies, retained austenite, and martensite) of the multiphased TRIP steel microstructure. The complex relationships between the volume fraction of the retained austenite, the morphology and distribution of all phases present in the microstructure, and the mechanical properties of TRIP steel were revealed. The bainite morphology had a more pronounced effect on the mechanical behavior than the refinement of the microstructure. The improvement of the mechanical properties of TRIP steel was achieved by variation of the volume fraction of the retained austenite rather than the overall refinement of the microstructure.