Experiment and theoretical prediction of martensitic transformation crystallography in a Ni–Mn–Ga ferromagnetic shape memory alloy

A detailed study of martensitic transformation crystallography and microstructural characteristics in the Ni53Mn25Ga22 ferromagnetic shape memory alloy (FSMA) was performed by both experimental observation and theoretical calculation. It is revealed that there are two microscopically twin-related martensitic variants with a misorientation of ∼82° around the 〈1 1 0〉_M axis in each initial austenite grain. The twin interface plane was determined to be {0.399 0.383 0.833}_M (1.79° away from {1 1 2}_M). The ratio of the amounts of the two variants inherited from one single austenite grain is about 1.70. The prevalent orientation relationship between austenite and martensite was found to be Kurdjumov–Sachs (K–S) relationship with (1 1 1)_A//(1 0 1)_M, [110]A//[111]_M. A successful explanation of the crystallographic features during martensitic transformation will shed light on the development of FSMAs with optimal performance.

The effect of microstructure on the decrease of the apparent Young's Modulus in DP 780 steel

Currently, there is a significant effort into developing novel multiphase microstructures to further improve the strength/ductility combination of advanced high-strength steels. To achieve this, the effect of the microstructure on sheet formability needs to be further understood. In this study, the effect of the microstructure on the variation of the elastic modulus in loading and unloading of DP 780 steel has been investigated. Five microstructures with varying volume fractions of ferrite and martensite were generated using different heat treatment cycles. Tension tests were performed to different strain values and the Young’s Modulus during loading and unloading was determined. The test results show that the reduction in unloading modulus with prestrain depends on the volume fraction and hardness of the martensitic phase.

The martensitic transformation texture in Ti-6Al-4V

The transformation texture associated with martensite formation in the titanium alloy Ti- 6Al-4V has been investigated. Samples were heated into the fully b phase and quenched to form a microstructure of very fine a' martensite with no evidence of diffusional transformation at the prior b grain boundaries. EBSD texture measurements on the martensite showed that within each prior b grain, although typically all 12 variants of a’ were formed, the fractions of variants was far from uniform. The a’ texture was markedly different from values calculated using equal variant probability, also indicating that significant variant selection was occurring during martensitic transformation. This effect was modelled on the basis of elastic interaction between martensite events.

Structure and phase stability of NiMnGa ferromagnetic shape memory alloys by experimental and ab-initio techniques

This paper summarizes some of our recent results on crystal structure, microstructure, orientation relationship between martensitic variants and crystallographic features of martensitic transformation in Ni-Mn-Ga FSMAs. It was shown that Ni53Mn25Ga22 has a tetragonal I4/mmm martensitic structure at room temperature. The neighboring martensitic variants in Ni53Mn25Ga22 have a compound twinning relationship with the twinning elements K1={112}, K2={11-2}, η1=<11-1>, η2=<111>, P={1-10} and s=0.379. The ratio of the relative amounts of twins within the same initial austenite grain is ~1.70. The main orientation relationship between austenite and martensite is Kurdjumov-Sachs (K-S) relationship. Based on the crystallographic phenomenological theory, the calculated habit plane is {0.690 -0.102 0.716}A (5.95° from {101}A), and the magnitude, direction and shear angle of the macroscopic transformation shear are 0.121, <-0.709 0.105 0.698>A (6.04° from <-101>A) and 6.88°, respectively.

Ultrafine grain formation in a Ti-6Al-4V alloy by thermomechanical processing of a martensitic microstructure

In the current study, ultrafine equiaxed grains with a size of 150 to 800 nm were successfully produced in a Ti-6Al-4V alloy through thermomechanical processing of a martensitic starting microstructure. This was achieved through a novel mechanism of grain refinement consisting of several concurrent processes. This involves the development of substructure in the lath interiors at an early stage of deformation, which progressed into small high-angle segments with increasing strain. Consequently, the microstructure was gradually transformed to an equiaxed ultrafine grained structure, mostly surrounded by high-angle grain boundaries, through continuous dynamic recrystallization. Simultaneously, the supersaturated martensite was decomposed during deformation, leading to the progressive formation of beta phase, mainly nucleated on the intervariant lath boundaries.

Effect of retained austenite on wear resistance of nanostructured dual phase steels

Nanostructured super bainitic and quenching-partitioning (Q&P) martensitic steels with a significant amount of retained austenite obtained by low temperature bainitic transformation and Q&P respectively were studied to explore the effect of retained austenite on stirring wear resistance. The results suggest that the Q&P martensitic steel significantly enhanced the hardness of the worn surface (from 674 to 762 HV1) and increased the thickness of the deformed layer (,3.3 mm), compared to the nanostructured bainitic steel. The underlying reason is that the Q&P martensitic steel has a higher stability of retained austenite thereby providing a superior transformation induced plasticity effect to increase surface hardness and reduce wear rate during the wear process.