Reinforcement and deformation behaviors of polyvinyl alcohol/graphene/montmorillonite clay composites

We report the synergistic reinforcement and deformation of polyvinyl alcohol (PVA)/graphene/montmorillonite clay (MMT) composites with the tensile properties being improved greatly. Particularly, the tensile strength and modulus of PVA composite with 0.9 wt% graphene and 0.3 wt% of MMT were improved by more than 58% and 43% when compared to the neat PVA, respectively, and were at least 10% higher than the enhanced sum of dual PVA composites with 0.9 wt% graphene and 0.3 wt% MMT. This reinforcement was resulted from the good dispersion and effective interfacial interactions as confirmed from morphology investigation, increased glass transition temperature and the shift of O-H stretching. When there were no fillers i.e. in situ reduced graphene (IRG) or MMT or their loading was low, high alignment of PVA could be observed, with increased crystallinity, melting point, lamellae thickness but narrowed crystallite size distribution. The synergistic reinforcement of PVA achieved from combined incorporation of IRG and MMT will pave the way for the development of stronger PVA composites in various applications.

Simultaneous crystallization and decomposition of PVA/MMT composites during non-isothermal process

Decomposition of poly(vinyl alcohol)/montmorillonite clay (PVA/MMT) composites during melting-crystallization was experimentally confirmed by morphology and molecular structure changes. In particular, FTIR spectra show the shift of O-H stretching band as well as enhanced intensities of C-O stretching and CH2 rocking vibrational modes. Furthermore, Raman deconvolution indicates that C-H wagging, CH2-CH wagging, CH-CO bending and CH2 wagging modes in amorphous domains were all decreased greatly. Moreover, this decomposition leads to decreased melting enthalpy, melting point, crystallization enthalpy and crystallization temperature. Crystallization analysis shows that the MMT incorporated slows down the crystallization process in the PVA matrix regardless of the nucleation capability of MMT. Despite the severe decomposition, the crystallization kinetics still corroborated well with common classical models. As a result, molecular structure changes and crystallization retardation observed in this study clearly indicate the strong effects of the thermal degradation on the non-isothermal crystallization of PVA/MMT composites.

Novel nanocomposite fibres for technical textile applications : synthesis and characterisation of poly(m-xylene adipamide) montmorillonite nanocomposites

Technical textiles, based on advanced polymeric materials, are an important segment of the synthetic textile market. This area has seen considerable growth in recent times, now accounting for almost 25% of all manufactured synthetic fibres, and has driven the recent development of a range of specialist high performance polymer fibres that are stronger, lighter or have improved heat and fire resistance. However, the increasing size of the market has highlighted the need for materials that have improved performance whilst maintaining low manufacturing costs. These factors have resulted in a change in how new specialty fibres are developed and the emphasis in this field is now on the upgrading or improving of the properties of commodity (conventional) fibres by modifying their properties to suit specific applications.

This paper will describe our work on preparing novel polymer nanocomposite fibres by the addition of clay nanoparticles during melt extrusion. The effect of the nanoparticles on the processing of the fibres and the result on the physical morphology and mechanical properties will be described.

Nonisothermal Crystallization Behavior of Poly(m-xylene adipamide)/Montmorillonite Nanocomposites

This article reports the nonisothermal crystallization behavior of MXD6 and its clay nanocomposite system (MXD6/MMT) using differential scanning calorimetry (DSC). The DSC experimental data were analyzed by theoretical modeling of the crystallization kinetics using the Avrami, Ozawa, Jeziorny, and the combined Avrami―Ozawa semiempirical models. It has been determined that these models adequately described the crystallization behavior of the MXD6 nanocomposite at cooling rates below 20 °C/min, but there was a deviation from linear dependence at higher cooling rates. This was attributed to changes of both the free energy and the cooling crystallization function K(T) over the entire crystallization process, as well as possible relaxation effects leading to structural rearrangements. In addition, the activation energy determined using the differential isoconversional method of Friedman was also found to vary, indicating changes in both the free energy and crystallization mechanism. Despite the lack of a reliable theoretical model, the heterogeneous nucleating activity of the MMT nanoparticles was demonstrated and quantified using Dobreva's method (Φ = 0.71), and the crystallization rate for the nanocomposite system was found to be greater than pure MXD6 by up to 79% at 40 °C/min.

The effect of alternate heating rates during cure on the structure-property relationships of epoxy/MMT clay nanocomposites

This paper investigates the effect of both the mixing technique and heating rate during cure on the dispersion of montmorillonite (MMT) clay in an epoxy resin. The combination of sonication and using a 10. °C/min heating rate during cure was found to facilitate the dispersion of nanoclay in epoxy resin. These processing conditions provided a synergistic effect, making it possible for polymer chains to penetrate in-between clay galleries and detach platelets from their agglomerates. As the degree of dispersion was enhanced, the flexural modulus and strength properties were found to decrease by 15% and 40%, respectively. This is thought to be due to individual platelets fracturing in the nanocomposite. Complementary techniques including X-ray diffraction (XRD), small angle X-ray scattering (SAXS), scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy (TEM) and optical microscopy were essential to fully characterise localised and spatial regions of the clay morphologies.

The effect of a rapid heating rate, mechanical vibration and surfactant chemistry on the structure-property relationships of epoxy/clay nanocomposites

The role of processing conditions and intercalant chemistry in montmorillonite clays on the dispersion, morphology and mechanical properties of two epoxy/clay nanocomposite systems was investigated in this paper. This work highlights the importance of employing complementary techniques (X-ray diffraction, small angle X-ray scattering, optical microscopy and transmission electron microscopy) to correlate nanomorphology to macroscale properties. Materials were prepared using an out of autoclave manufacturing process equipped to generate rapid heating rates and mechanical vibration. The results suggested that the quaternary ammonium surfactant on C30B clay reacted with the epoxy during cure, while the primary ammonium surfactant (I.30E) catalysed the polymerisation reaction. These effects led to important differences in nanocomposite clay morphologies. The use of mechanical vibration at 4 Hz prior to matrix gelation was found to facilitate clay dispersion and to reduce the area fraction of I.30E clay agglomerates in addition to increasing flexural strength by over 40%.

Synergistic reinforcement, crystallization and degradation of PVA-graphene-clay composites

 Initially, synergistic reinforcement PVA composite has been successfully developed by using graphene and MMT. Furthermore, new knowledge of the crystallization mechanism of the PVA and PVA composites was revealed. Finally, Isothermal degradation kinetics models and mechanism of the as-prepared composites were also proposed.

The influence of processing techniques on the matrix distribution and filtration of clay in a fibre reinforced nanocomposite

A nano-modified matrix based on an epoxy resin and montmorillonite (MMT) layered silicates, was successfully infiltrated through 10 ply of carbon fibre preform. A combined fabrication process of a vacuum assisted resin infusion method (VARIM) followed by a rapid heating rate and mechanical vibration during cure, facilitated the infiltration of the nano-modified matrix through the preform. This was achieved by dispersing the MMT clay in the resin and ensuring that the viscosity of the nano-modified matrix remained low during fabrication. SEM-EDX (energy dispersive X-ray spectroscopy) spectra showed that chemical constituents within MMT clay including silicon, aluminium and magnesium elements had permeated through the fibre preform and were detected throughout the laminate. A homogeneous resin/particle distribution was achieved with the size of clay particles ranging from 100 nm to 1 μm.

Effects of clay amendment on adsorption and desorption of copper in water repellent soils

Copper is an important micronutrient and trace amounts are essential for crop growth. However, high concentrations of copper will produce toxic effects. Australia is increasingly developing production of crops in water repellent soils. Clay amendment, a common amelioration techniques used in Australia, has demonstrated agronomic benefits in increased crop or pasture production. The sorption and desorption of copper and the effect of clay treatment on copper behaviour in a water repellent soil collected from an experimental farm in South Australia is studied. We found that the water repellent soils amended with clay have an increased adsorption capacity of copper. Also the clay-amended soils had an increased ratio of specific sorption to total sorption of copper. The implications of this study to the sustainable agro-environmental management of water repellent soils is discussed.

High technology nanocomposite fibres: Development of melt spun semi-aromatic polyamide nanocomposite fibres

Novel polyamide nanocomposite fibres have been produced by compounding semi aromatic Poly (m-xylene adipamide) (MXD6) and organophilic Montmorillonite (MMT). Partially orientated fibres (POF) of MXD6 nanocomposite were obtained by melt spinning on a multifilament fibre extrusion system at three different speeds. The effect of the drawing velocity
on the mechanical properties of the filaments has been determined. Tensile measurements indicated that the introduction of the nanoparticies by melt intercalation improves the tenacity and toughness of the resulting polyamide fibres. The microstructure of the nanocomposites was examined by X-ray diffraction and Transmission Electron Microscope (TEM) and shown to
be an exfoliated disordered structure. The thermal stability of MXD6 nanocomposites was analysed by thermo gravimetric analysis (TGA) suggesting stabilisation of the clay and the polymer systems above 450°C.

Water repellency, near-saturated infiltration and preferential solute transport in a macroporous clay soil

Little attention has been paid to the possibility that soil water repellency could enhance non-equilibrium water flow and solute transport through macropores present in structured clay soils. In this study, we measured infiltration and solute transport in a clay soil under near-saturated conditions in both the field using tension infiltrometers and in the laboratory on undisturbed soil columns. Measurements were made on adjacent plots under grass and continuous arable cultivation. Steady-state field infiltration rates measured using water and ethanol as the infiltrating fluids demonstrated that the soil macroporosity under grass was better developed, but that much of the structural pore system was inactive due to water repellency. No water repellency was detected on the arable plot disturbed by tillage. Dye tracing showed that the conducting macroporosity was largely comprised of earthworm channels in the grassed plot and inter-aggregate voids resulting from ploughing in the arable plot. Tracer breakthrough curves measured on field-dry soil indicated rapid macropore transport in columns taken from both plots, although the degree of non-equilibrium transport appeared somewhat stronger under grass. This result, which was attributed to water repellency, was also consistent with the larger flow-weighted mean pore size found in the field infiltration experiments. It is concluded that water repellency in undisturbed structured clay soils can have significant effects on the occurrence of non-equilibrium water and solute transport in macropores.

'You moulded me like clay': David Almond's sexualised monsters

Naarah Sawers is an Alfred Deakin Post-Doctoral Research Fellow at Deakin University where she is researching environmental agendas in computer games for children. She has also published and researched in children's literature in the area of feminist bio-ethics and agency.