Degradation of VOCs by phototcatalytic oxidation reactor using TiO2 pellets

Volatile Organic Compounds (VOCs) are air pollutants that come from burning fossil fuels and industrial emissions. They have potentially adverse health effects being carcinogenic and highly persistent in the environment. The use of photocatalytic oxidation to remove VOCs has the potential to be applied in indoor air quality improvement and industrial emission control. A fixed bed photocatalytic reactor was designed and built. UV black light lamps were installed in the reactor to provide a source of UV radiation. A non-film titania media as pellets were placed on the three fixed beds within the reactor. Toluene and acetone were used as indicators of VOCs during the experiment. With a flow rate of 12.75l/min, the oxidation efficiencies were obtained at four different concentrations of acetone laden gas streams ranging from 40ppm to 250ppm. It was found that the lower the acetone concentration of the untreated inlet gas, the higher the oxidation efficiency. The oxidation efficiency was in the range of 40–70% for various concentrations of untreated gases. Two concentrations of toluene laden gas stream were also tested using the same reactor. The oxidation efficiencies were found as 50% for 120ppm toluene gas and 45% for 300ppm toluene gas. It was found that the times required for toluene to reach oxidization equilibrium have been halved than for acetone gas stream. Other parameters such as flow rate and UV intensity were also altered to see their effects on the oxidation efficiency. A full spectrum scan was carried out using a Bio-rad Infrared spectrometer. It was found that the main components of the treated gas stream from the outlet of the reactor were CO2 and water along with small amount of untreated acetone. The suspected intermediates of aliphatic hydrocarbons and CO were found in very minimal amounts or undetectable. The research experiments supported that the TiO2 pellets can work effectively in a fixed bed photocatalytic reactor and achieve significant oxidation efficiencies for degradation of toluene and acetone as indicators of VOCs.

Photocatalytic decolorization of lanasol blue CE dye solution using a flat-plate reactor

This paper reports the effectiveness of the photocatalysis TiO₂ in degrading Lanasol Blue CE. A flat-plate reactor (FPR) with a reactor area of 0.37 m² and ultraviolet (UV) light source of six 36 W blacklight lamps was used in the study. Operating variables including dosage of the photocatalyst, flow rates through the FPR, UV intensity, and tilted angle of the reactor were investigated to degrade Lanasol Blue CE. Results showed that the photocatalytic process can efficiently remove the color in textile dyeing effluent. The degradation process was approximated using first-order kinetics. The photocatalytic apparent reaction rate increased with the increasing UV intensity received by the photocatalyst TiO₂ in slurry. The liquid flow rate and tilted angle influenced the film thickness. The apparent reaction rate constant was mainly determined by the liquid film thickness, UV intensity, and the dosage of the photocatalyst. The findings of this research can be utilized as preliminary input for potential solar photocatalytic applications on color removal from dye solutions.

Photocatalytic production of methane and hydrogen through reduction of carbon dioxide with water using titania pellets

This paper presents an experimental study on employing a pellet form of catalyst in photo-reduction of carbon dioxide with water. Water was first absorbed into titania pellets. Highly purified carbon dioxide gas was then discharged into a reactor containing the wet pellets, which were then illuminated continuously for 65 hours using UVC lamps. Analysing the products accumulated in the reactor confirmed that methane and hydrogen were produced through photo-reduction of carbon dioxide with water. No other hydrocarbons were detected. Increasing the temperature in the reactor has showed little change on the amount of methane produced.

Photocatalytic reduction of carbon dioxide into gaseous hydrocarbon using TiO2 pellets

It has been shown that CO₂ could be transformed into hydrocarbons when it is in contact with water vapour and catalysts under UV irradiation. This paper presents an experimental set-up to study the process employing a new approach of heterogeneous photocatalysis using pellet form of catalyst instead of immobilized catalysts on solid substrates. In the experiment, CO₂ mixed with water vapour in saturation state was discharged into a quartz reactor containing porous TiO₂ pellets and illuminated by various UV lamps of different wavelengths for 48 h continuously. The gaseous products extracted were identified using gas chromatography. The results confirmed that CO₂ could be reformed in the presence of water vapour and TiO₂ pellets into CH₄ under continuous UV irradiation at room conditions. It showed that when UVC (253.7 nm) light was used, total yield of methane was approximately 200 ppm which was a fairly good reduction yield as compared to those obtained from the processes using immobilized catalysts through thin-film technique and anchoring method. CO and H₂ were also detected. Switching from UVC to UVA (365 nm) resulted in significant decrease in the product yields. The pellet form of catalyst has been found to be attractive for use in further research on photocatalytic reduction of CO₂.

Photosynthesis of hydrogen and methane as key components for clean energy system

While researchers are trying to solve the world's energy woes, hydrogen is becoming the key component in sustainable energy systems. Hydrogen could be produced through photocatalytic water-splitting technology. It has also been found that hydrogen and methane could be produced through photocatalytic reduction of carbon dioxide with water. In this exploratory study, instead of coating catalysts on a substrate, pellet form of catalyst, which has better adsorption capacity, was used in the photo-reduction of carbon dioxide with water. In the experiment, some water was first absorbed into titanium dioxide pellets. Highly purified carbon dioxide gas was then discharged into a reactor containing these wet pellets, which were then illuminated continuously using UVC lamps. Gaseous samples accumulated in the reactor were extracted at different intervals to analyze the product yields. The results confirmed that methane and hydrogen were photosynthesized using pellet form of TiO₂ catalysts. Hydrogen was formed at a rate as high as 0.16 micromoles per hour (μmol h⁻¹). The maximum formation rate of CH₄ was achieved at 0.25 μmol h⁻¹ after 24 h of irradiation. CO was also detected.

A comparative study on accelerated weathering tests of wool fabrics

This work has used two lightboxes with Philips 500 W MBTF lamps for a comparative trial on the photoyellowing evaluation of untreated wool fabrics under dry and wet conditions. An investigation was made to account for different trends of photoyellowing of the same wool fabric when irradiated by the two lightboxes. The fabric specimens irradiated in one lamp experienced increasing yellowing with irradiation time while specimens from the same wool fabric but irradiated under the other lamp manifested no noticeable color change. These differences are attributed to the susceptibility of wool to small spectral differences between the two MBTF lamps. Furthermore, the color fading results obtained from the commonly used blue wool standard (BWS) references from L1 to L3 show that these reference materials could not effectively reveal changes caused by the spectral differences in two MBTF lamps. These results have important implications for conducting accelerated weathering tests on spectrum-sensitive textile materials, and considerable care should be taken when using BWSs to ensure reliable and consistent irradiation results.

The role of ultraviolet-A reflectance and ultraviolet-A induced fluorescence in the appearance of budgerigar plumage: insights from spectrofluorometry and reflectance spectrophotometry

Fluorescence has so far been found in 52 parrot species when illuminated with ultraviolet-A (UVA) 'black' lamps, and two attempts have been made to determine whether such fluorescence plays any role in sexual signalling. However, the contribution of the reflectance versus fluorescence to the total radiance from feathers, even in the most studied species to date (budgerigars), is unclear. Nor has the plumage of this study species been systematically assessed to determine the distribution of fluorescent patches. We therefore used spectrofluorometry to determine which areas of budgerigars fluoresce and the excitation and emission spectra involved; this is the first time that such a technique has been applied to avian plumage. We found that both the yellow crown and (normally hidden) white downy chest feathers exhibit strong UVA-induced fluorescence, with peak emissions at 527 nm and 436 nm, respectively. Conversely, the bright-green chest and dark-blue tail feathers do not fluoresce. When comparing reflectance spectra (400700 nm) from the yellow crown using illuminants with a proportion of UVA comparable to daylight, and illuminants with all UVA removed, no measurable difference resulting from fluorescence was found. This suggests that under normal daylight the contribution of fluorescence to radiance is probably trivial. Furthermore, these spectra revealed that males had fluorescent crowns with substantially higher reflectance than those of females, in both the UV waveband and at longer wavelengths. Reflectance spectrophotometry was also performed on a number of live wild-type male budgerigars to investigate the chromatic contrast between the different plumage areas. This showed that many plumage regions are highly UV-reflective. Overall our results suggest that rapid surveys using UVA black lamps may overestimate the contribution of fluorescence to plumage coloration, and that any signalling role of fluorescence emissions, at least from the yellow crown of budgerigars, may not be as important as previously thought.

CFL bulbs : environmentally friendly and sustainable?

The purpose of this paper is to document the positive and negative characteristics of using compact fluorescent lamps (CFL) and to raise awareness and debate about the potential negative health effects resulting from prolonged exposure to CFLs. This is a theoretical paper and, primarily, incorporates the literature and the author’s experiences of CFLs. Governmental and non-governmental measures in the area of recycling and disposal of CFLs are also presented. This is a relatively new area of research; hence, very limited academic literature is currently available. Discussion of the issue of increased usage of CFLs is timely following heightened debate on greenhouse gas emissions and climate change. Increased debate amongst the policy and decision-makers will assist the public to make an informed decision. It is also anticipated that this debate will put pressure on the manufacturers of all types of bulbs, and government and non-governmental agencies to enhance their own and community initiatives to recycle and/or safely dispose of CFLs. No other similar review of the advantages and weaknesses of using CFLs has been undertaken that encourages the reader and potential users of CFLs to reflect on their choices.