An investigation of yarn snarling and balloon flutter instabilities in ring spinning

This article reports theoretical and experimental investigation on yarn snarling and balloon fluttering in ring spinning. Yarn snarling and balloon fluttering affect yarn breakage in ring spinning. The theoretical model has incorporated the tangential component of air drag on a ballooning yarn, which was ignored in previous models. The results show that yarn snarling happens in the balloon when the ratio of yarn length in the balloon to balloon height is greater than a specific value that depends on the yarn type and count. Yarn tension experiences an obvious change before and after yarn snarling. The balloon flutter appears between normal balloons while the balloon loops are changing. Fluttering balloon shapes that oscillate periodically between two and three loop configurations as yarn tension varies periodically have also been observed experimentally.

Quantifying turbulent mixing and oxygen fluxes in a Mediterranean-type, microtidal estuary

Experiments were carried out on an intermittent estuary during its closed (summer) and open (winter) states to identify the physical processes responsible for vertical mixing across the halocline, and to quantify vertical fluxes of oxygen and salt between water layers. During the blocked phase a two-layer structure was observed, with a brackish surface layer overlying old seawater. Within a deep basin the wind-driven turbulent mixing was consistent with the measured surface-layer turbulent dissipation, but the dissipation in the bottom layer appeared to be driven by internal seiching. In the shallow regions of the estuary vertical fluxes of dissolved oxygen were indicative of oxygen demand by respiration and remineralization of organic material in bottom water and sediments. During the estuary's open phase a three-layer structure was observed, having a fresh, river-derived surface layer, a middle layer of new seawater, and a bottom layer of old seawater. In the shallower regions surface-layer turbulent diffusion was consistent with the strong, gusty winds experienced at the time. The dissolved oxygen of the incoming seawater decreased to very low values by the time it reached the upstream deep basin as a result of the low cross-pycnocline oxygen flux being unable to compensate for the oxygen utilization. At least 50 % of the cross-pycnocline salt fluxes in the shallow reaches of the open estuary are suggested to be driven by Holmboe instabilities.

Dynamics of interactions involving deformable drops : hydrodynamic dimpling under attractive and repulsive electrical double layer interactions

A model developed previously to analyze force measurements between two deformable droplets in the atomic force microscope [Langmuir 2005, 21, 2912-2922] is used to model the drainage of an aqueous film between a mica plate and a deformable mercury drop for both repulsive and attractive electrical double-layer interactions between the mica and the mercury. The predictions of the model are compared with previously published data [Faraday Discuss. 2003, 123, 193-206] on the evolution of the aqueous film whose thickness has been measured with subnanometer precision. Excellent agreement is found between theoretical results and experimental data. This supports the assumptions made in the model which include no-slip boundary conditions at both interfaces. Furthermore, the successful fit attests to the utility of the model as a tool to explore details of the drainage mechanisms of nanometer-thick films in which fluid flow, surface deformations, and colloidal forces are all involved. One interesting result is that the model can predict the time at which the aqueous film collapses when attractive mica-mercury forces are present without the need to invoke capillary waves or other local instabilities of the mercury/electrolyte interface.

Mixing layer oscillations for a submerged horizontal wall-jet

Measurements of the horizontal velocity component were made for a horizontal wall-jet emanating from a submerged sluice gate forming one side of a large flow compartment. The existence of large-scale vortex structures was quantified by spectral analysis of the velocity measurements taken at various distances from the floor of the flow compartment, for different measurement stations from the jet exit. Close to the jet exit, the spectra of the velocity measurements within the potential core exhibit multiple peaks. Further downstream, the spectra are more defined and peak at the same frequency, irrespective of whether the measurements were made within the potential core or the mixing layer. The spectral peak corresponds to the passage frequency of large-scale vortex structures. Downstream of the potential core, the peak frequencies of the velocity spectra increase as the measurement location was moved towards the floor of the flow compartment. The increase in peak frequencies is attributed to fluctuations associated with the wall boundary layer. Predictions of the mixing layer instabilities were made using linear stability analysis. The predictions are in good agreement with the observed vortex shedding frequencies in the mixing layer

Comparison of various NMR methods for the indirect detection of nitrogen-14 nuclei via protons in solids

We present an experimental comparison of several through-space Hetero-nuclear Multiple-Quantum Correlation experiments, which allow the indirect observation of homo-nuclear single- (SQ) or double-quantum (DQ) ¹⁴N coherences via spy ¹H nuclei. These ¹H-{¹⁴N} D-HMQC sequences differ not only by the order of ¹⁴N coherences evolving during the indirect evolution, t1, but also by the radio-frequency (rf) scheme used to excite and reconvert these coherences under Magic-Angle Spinning (MAS). Here, the SQ coherences are created by the application of center-band frequency-selective pulses, i.e. long and low-power rectangular pulses at the ¹⁴N Larmor frequency, ν0(¹⁴N), whereas the DQ coherences are excited and reconverted using rf irradiation either at ν0(¹⁴N) or at the ¹⁴N overtone frequency, 2ν0(¹⁴N). The overtone excitation is achieved either by constant frequency rectangular pulses or by frequency-swept pulses, specifically Wide-band, Uniform-Rate, and Smooth-Truncation (WURST) pulse shapes. The present article compares the performances of four different ¹H-{¹⁴N} D-HMQC sequences, including those with ¹⁴N rectangular pulses at ν0(¹⁴N) for the indirect detection of homo-nuclear (i) ¹⁴N SQ or (ii) DQ coherences, as well as their overtone variants using (iii) rectangular or (iv) WURST pulses. The compared properties include: (i) the sensitivity, (ii) the spectral resolution in the ¹⁴N dimension, (iii) the rf requirements (power and pulse length), as well as the robustness to (iv) rf offset and (v) MAS frequency instabilities. Such experimental comparisons are carried out for γ-glycine and l-histidine.HCl monohydrate, which contain ¹⁴N sites subject to moderate quadrupole interactions. We demonstrate that the optimum choice of the ¹H-{¹⁴N} D-HMQC method depends on the experimental goal. When the sensitivity and/or the robustness to offset are the major concerns, the D-HMQC sequence allowing the indirect detection of ¹⁴N SQ coherences should be employed. Conversely, when the highest resolution and/or adjusted indirect spectral width are needed, overtone experiments are the method of choice. The overtone scheme using WURST pulses results in broader excitation bandwidths than that using rectangular pulses, at the expense of reduced sensitivity. Numerically exact simulations also show that the sensitivity of the overtone ¹H-{¹⁴N} D-HMQC experiment increases for larger quadrupole interactions.

Strain localisation patterns under equal-channel angular pressing

Instabilities of plastic flow in the form of localised shear bands were experimentally observed to result from equal-channel angular pressing (ECAP) of magnesium alloy AZ31. The appearance of shear bands and their spacing were dependent on velocity of the pressing and applied back-pressure. A generic gradient plasticity theory involving second-order strain gradient terms in a constitutive model was applied to the case of AZ31 deformed by ECAP. Linear stability analysis was applied to the set of equations describing the deformation behaviour in the process zone idealised as a planar shear zone. A full analytical solution providing a dispersion relation between the rate of growth of a perturbation and the wave number was obtained. It was shown that the pattern of incipient localised shear bands exhibits a spectrum of characteristic lengths corresponding to admissible wave numbers. The interval of the spectrum of wave numbers of viable, i.e. growing, perturbations predicted by linear stability analysis was shown to be in good agreement with the experimentally observed spectrum. The effect of back-pressure applied during ECAP was also considered. The predicted displacement of the shear band spectrum towards lower wave numbers, shown to be a result of the decreased shear strain rate in the shear zone, was consistent with the experimentally observed increase of the band spacing with increased back-pressure. A good predictive capability of the general modelling frame used in conjunction with linear stability analysis was thus demonstrated in the instance of the particular alloy system and the specific processing conditions considered.

Dry sliding wear of active screen plasma carburised austenitic stainless steel

Low temperature diffusion treatments with nitrogen and carbon have been widely used to increase the tribological performance of austenitic stainless steels. These processes produce a layer of supersaturated austenite, usually called expanded austenite or S-phase, which exhibits good corrosion and wear resistance. The novel active screen technology is said to provide benefits over the conventional DC plasma technology. The improvements result from the reduction in the electric potential applied to the treated components, and the elimination of such defects and processing instabilities as edge effects, hollow cathode effects and arcing. In this study, AISI 316 coupon samples were plasma carburised in DC and active screen plasma furnaces. The respective layers of carbon expanded austenite were characterised and their tribological performance was studied and compared. Detailed post-test examinations included SEM observations of the wear tracks and of the wear debris, EDX mapping of the wear track, EBSD crystal orientation mapping of the cross sections of the wear tracks, and cross-sectional TEM. Based on the results of wear tests and post-test examinations, the wear mechanisms involved are discussed.

Study of active screen plasma processing conditions for carburising and nitriding austenitic stainless steel

Active screen (AS) is an advanced technology for plasma surface engineering, which offers some advantages over conventional direct current (DC) plasma treatments. Such surface defects and process instabilities as arcing, edge and hollow cathode effects can be minimised or completely eliminated by the AS technique, with consequent improvements in surface quality and material properties. However, the lack of information and thorough understanding of the process mechanisms generate scepticism in industrial practitioners. In this project, AISI 316 specimens were plasma carburised and plasma nitrided at low temperature in AS and DC furnaces, and the treated samples were comparatively analysed. Two diagnostic techniques were used to study the plasma: optical fibre assisted optical emission spectroscopy, and a planar electrostatic probe. Optimum windows of treatment conditions for AS plasma nitriding and AS plasma carburising of austenitic stainless steel were identified and some evidence was obtained on the working principles of AS furnaces. These include the sputtering of material from the cathodic mesh and its deposition on the worktable, the generation of additional active species, and the electrostatic confinement of the plasma within the operative volume of the furnace.