Synthesis of LiFePO4@carbon nanotube core-shell nanowires with a high-energy efficient method for superior lithium ion battery cathodes

A high-energy efficient method is developed for the synthesis of LiFePO4@CNT core-shell nanowire structures. The method consists of two steps: liquid deposition approach to prepare FePO4@CNT core-shell nanowires and solvothermal lithiation to obtain the LiFePO4@CNT core-shell nanowires at a low temperature. The solution phase method can be easily scaled up for commercial application. The performance of the materials produced by this method is evaluated in Li ion batteries. The one-dimensional LiFePO4@CNT nanowires offer a stable and efficient backbone for electron transport. The LiFePO4@CNT core-shell nanowires exhibit a high capacity of 132.8 mAh g^-1 at a rate of 0.2C, as well as high rate capability (64.4 mAh g^-1 at 20C) for Li ion storage.

The competition between metastable and equilibrium S (Al2CuMg) phase during the decomposition of AlCuMg alloys

Abstract The decomposition sequence of the supersaturated solid solution leading to the formation of the equilibrium S (Al2CuMg) phase in AlCuMg alloys has long been the subject of ambiguity and debate. Recent high-resolution synchrotron powder diffraction experiments have shown that the decomposition sequence does involve a metastable variant of the S phase (denoted S1), which has lattice parameters that are distinctly different to those of the equilibrium S phase (denoted S2). In this paper, the difference between these two phases is resolved using high-resolution synchrotron and neutron powder diffraction and atom probe tomography, and the transformation from S1 to S2 is characterised in detail by in situ synchrotron powder diffraction. The results of these experiments confirm that there are no significant differences between the crystal structures of S1 and S2, however, the powder diffraction and atom probe measurements both indicate that the S1 phase forms with a slight deficiency in Cu. The in situ isothermal aging experiments show that S1 forms rapidly, reaching its maximum concentration in only a few minutes at high temperatures, while complete conversion to the S2 phase can take thousands of hours at low temperature. The kinetics of S phase precipitation have been quantitatively analysed for the first time and it is shown that S1 phase forms with an average activation energy of 75 kJ/mol, which is much lower than the activation energy for Cu and Mg diffusion in an Al matrix (136 kJ/mol and 131 kJ/mol, respectively). The mechanism of the replacement of S1 with the equilibrium S2 phase is discussed.

Degradation observations of encapsulated planar CH3NH3PbI3 perovskite solar cells at high temperatures and humidity

The stability of encapsulated planar-structured CH3NH3PbI3 (MAPbI3) perovskite solar cells (PSCs) was investigated under various simulated environmental conditions. The tests were performed under approximately one sun (100 mW cm^-2) illumination, varying temperature (up to 85 °C cell temperature) and humidity (up to 80%). The application of advanced sealing techniques improved the device stability, but all devices showed significant degradation after prolonged aging at high temperature and humidity. The degradation mechanism was studied by post-mortem analysis of the disassembled cells using SEM and XRD. This revealed that the degradation was mainly due to the decomposition of MAPbI3, as a result of reaction with H2O, and the subsequent reaction of hydroiodic acid, formed during MAPbI3 decomposition, with the silver back contact electrode layer.

Study on LiFe1 − xSm xPO4/C used as cathode materials for lithium-ion batteries with low Sm component

LiFe1 − xSmxPO4/C cathode materials were synthesized though a facile hydrothermal method. Compared with high-temperature solid-phase sintering, the method can allow for the fabrication of low Sm content (2 %), a scarce and expensive rare earth element, while the presence of an optimized carbon coating with large amount of sp²-type carbon sharply increases the material’s electrochemical performance. The high-rate dischargeability at 5 C, as well as the exchange current density, can be increased by 21 and 86 %, respectively, which were attributed to the fine size and the large cell parameter a/c as much. It should be pointed out that the a/c value will be increased for the LiFePO4 Sm-doped papered by both of the two methods, while the mechanism is different: The value c is increased for the front and the value a is decreased for the latter, respectively.

Synthesis of Al-doped Mg2Si1-xSnx compound using magnesium alloy for thermoelectric application

Abstract Mg2Si1-xSnx thermoelectric compounds were synthesized through a solid-state reaction at 700 °C between chips of Mg2Sn-Mg eutectic alloy and silicon fine powders. The Al dopants were introduced by employing AZ31 magnesium alloy that contains aluminum. The as-synthesized Mg2Si1-xSnx powders were consolidated by spark plasma sintering at 650-700 °C. X-ray diffraction and scanning electron microscopy revealed that the Mg2Si1-xSnx bulk materials were comprised of Si-rich and Sn-rich phases. Due to the complex microstructures, the electrical conductivities of Mg2Si1-xSnx are lower than Mg2Si. As a result, the average power factor of Al0.05Mg2Si0.73Sn0.27 is about 1.5 × 10^-3 W/mK² from room temperature to 850 K, being less than 2.5 × 10^-3 W/mK² for Al0.05Mg2Si. However, the thermal conductivity of Mg2Si1-xSnx was reduced significantly as compared to Al0.05Mg2Si, which enabled the ZT of Al0.05Mg2Si0.73Sn0.27 to be superior to Al0.05Mg2Si. Lastly, the electric power generation from one leg of Al0.05Mg2Si and Al0.05Mg2Si0.73Sn0.27 were evaluated on a newly developed instrument, with the peak output power of 15-20 mW at 300 °C hot-side temperature.

Preparation of size-selective Mn3O4 hexagonal nanoplates with superior electrochemical properties for pseudocapacitors

Porous Mn3O4 hexagonal nanoplates were synthesized through annealing the hydrohausmannite precursor obtained by a one-pot hydrothermal process and by precisely controlling the concentrations of potassium hydroxide and glucose. The effect of potassium hydroxide and glucose on the growth of hexagonal nanoplates was investigated, and a growth mechanism was also proposed. Due to its abundant pores, the pure Mn3O4-based electrode exhibits excellent cycling stability with 100% capacity retention after 5000 cycles. The asymmetric supercapacitor exhibited high performance with an energy density of 17.276 W h kg^-1 at a power density of 207.3 W kg^-1 in a wide potential window of 1.5 V.

Enhanced photocatalytic activities of TiO2-SiO2 nanohybrids immobilized on cement-based materials for dye degradation

Using cement-based material as a matrix for photocatalytic hybrids is an important development for the large-scale application of photocatalytic technologies. In this work, photocatalytic activity of nanosized hybrids of TiO2/SiO2 (nano-TiO2-SiO2) for degradation of some organic dyes on cementitious materials was highlighted. For this purpose, an optimal inorganic sol-gel precursor was firstly applied to prepare the composites of nano-TiO2-SiO2 which was characterized by XRD, SEM and UV-Vis. Then, a thin layer was successfully coated on white Portland cement (WPC) blocks using a dipping process in a nano-TiO2-SiO2 solution. The effect of nano-TiO2-SiO2-coated WPC blocks on photocatalytic decomposition of three dyes, including Malachite green oxalate (MG), Methylene blue (MB) and Methyl orange (MO) were studied under UV irradiation and monitored by chemical oxygen demand tests. The results showed an increase in photocatalytic effects which depends on the structure and pH of the applied cement.

Photocatalytic degradation of bisphenol A by HMS/g-C3N4 composite

In this work, hexagonal mesoporous silica/g-C3N4 (HMS/C3N4) was synthesized by heating a mixture of self-prepared HMS and dicyandiamide. The as-prepared materials were characterized by transmission electron microscopy (TEM), X-ray diffractometer (XRD), Fourier transform infrared spectra (FT-IR) and Brunauer–Emmett–Teller analysis (BET). The prepared photocatalysts were applied to decompose bisphenol A (BPA) under UV light illumination. The mass ratios of HMS to melamine were optimized. The results showed that optimal mass ratios HMS to dicyandiamide was 1:1. Even though with the same catalyst dosage (1.0 g/L), the degradation kinetic rate constant of BPA over HMS/C3N4 (0.00526 min−1) was 1.76 times and 1.4 times than those on P25 (0.00298 min−1) and pure C3N4 (0.00383 min−1), while the rate constant of photolysis was only 0.00021 min−1. The enhanced photocatalytic activity of the HMS/C3N4 composite was ascribed to higher specific surface area and less aggregation compared to the pure C3N4. It is feasible and efficient to degrade BPA by HMS/C3N4 composite, which is easier to be separated than pure C3N4 after the pollutant has been removed completely.

CoP2 nanoparticles on reduced graphene oxide sheets as a super-efficient bifunctional electrocatalyst for full water splitting

In this communication, we report an electrocatalyst for full water splitting based on CoP2 nanoparticles grown on reduced graphene oxide sheets (CoP2/RGO). As a novel non-noble-metal electrocatalyst, CoP2/RGO shows an ultra-high catalytic activity in alkaline electrolyte which only requires a cell voltage of 1.56 V to attain a current density of 10 mA cm-2 for full water splitting.

"I could see, and yet, mon, I could na` see" : William Macewen, the agnosias, and brain surgery

Two little noticed cases in which William Macewen used symptoms of visual agnosia to plan brain surgery on the angular gyrus are reviewed and evaluated. Following a head injury, Macewen’s first patient had an immediate and severe visual object agnosia that lasted for about 2 weeks. After that he gradually became homicidal and depressed and it was for those symptoms that Macewen first saw him, some 11 months after the accident. From his examination, Macewen concluded that the agnosia clearly indicated a lesion in “the posterior portion of the operculum or in the angular gyrus.” When he removed parts of the internal table that had penetrated those structures the homicidal impulses disappeared. Macewen’s second patient was seen for a chronic middle ear infection and, although neither aphasic nor deaf, was ‘word deaf.’ Slightly later he became ‘psychically blind’ as well. Macewen suspected a cerebral abscess pressing on both the angular gyrus and the first temporal convolution. A large subdural abscess was found there and the symptoms disappeared after it was treated. The patients are discussed and Macewen’s positive results analysed in the historical context of the dispute over the proposed role of the angular gyrus as the visual centre.

Global factor trade with differentiated factor prices and factor intensities

Relaxing the assumption of internationally identical factor intensity techniques in the HOV model creates two challenges. First, computing actual factor intensity techniques of different countries requires detailed input-output tables and factor usage data, which are not always available. Second, determinants of the factor intensity technique differences across countries need to be identified. This paper explores the role of relative factor price differences in the determination of factor intensity technique differences across countries and proposes an inferring method that infers factor intensity techniques of different countries based on relative factor price differences. The HOV model is then modified accordingly.

Commerce mondial des facteurs de production quand les prix des facteurs sont différenciés et les intensités dans l'intensité d'utilisation des facteurs différentes. Relaxer le postulat de techniques à intensité identique de facteurs de production d'un pays à l'autre dans un modèle Heckscher-Ohlin-Vanek (HOV) pose deux défis. D'abord, mesurer les intensités en facteurs des techniques en place dans les divers pays réclame des tableaux interindustriels détaillés et des données sur l'utilisation des facteurs qui ne sont pas toujours disponibles. Ensuite, il faut identifier les déterminants des différences d'intensités en facteurs des techniques d'un pays à l'autre. Ce mémoire explore le rôle des différences dans les prix relatifs des facteurs dans la détermination des différences d'intensité en facteurs d'un pays à l'autre, et propose une méthode qui permet d'inférer les différences d'intensité en facteurs des techniques des divers pays à partir des différences dans les prix relatifs des facteurs. Le modèle HOV est alors modifié en conséquence.

Handling of absorbent information by aggregation operators

We propose a generalization of the notion of the absorbent element of aggregation operators. Our construction involves tuples of values that are absorbent, that is, that decide the result of aggregation. We analyze some basic properties of this generalization and determine the absorbent tuples of some popular classes of aggregation operators.

Multi-wavelets from B-spline super-functions with approximation order

Approximation order is an important feature of all wavelets. It implies that polynomials up to degree p−1 are in the space spanned by the scaling function(s). In the scalar case, the scalar sum rules determine the approximation order or the left eigenvectors of the infinite down-sampled convolution matrix H determine the combinations of scaling functions required to produce the desired polynomial. For multi-wavelets the condition for approximation order is similar to the conditions in the scalar case. Generalized left eigenvectors of the matrix H_f; a finite portion of H determines the combinations of scaling functions that produce the desired superfunction from which polynomials of desired degree can be reproduced. The superfunctions in this work are taken to be B-splines. However, any refinable function can serve as the superfunction. The condition of approximation order is derived and new, symmetric, compactly supported and orthogonal multi-wavelets with approximation orders one, two, three and four are constructed.

Local energy, the pre-envelope, and filter resolution

We examine the construction of new filters for computing local energy, and compare these filters with the Gabor filters and the three-point-filter of Venkatesh [l]. Further, we demonstrate that the effect of convolution with complex Gabor filters is to band-pass (with some differentiating effect) and compute the local energy of the result. The magnitude of the resulting local energy is then used to detect features [2], [3] (step features, texture etc.), and the phase is used to classify the detected features [l], [4] or provide disparity information for stereo [5] and motion work [6], [7]. Each of these types of information can be obtained at multiple resolutions, enabling the use of course to fine strategies for computing disparity, and allowing the discrimination of image textures on the basis of which parts of the Fourier domain they dominate [8], [9].

Acute rheumatic fever associated with household crowding in a developed country

Background: Acute rheumatic fever (ARF) and its sequelae, chronic rheumatic heart disease, remain important causes of morbidity and mortality worldwide, but there is little recent information about risk factors. The aim of this study was to examine the association between ARF and household crowding in New Zealand between 1996 and 2005.

Methods: This ecologic study used hospitalization data and census data to calculate incidence rates by census area unit (CAU). Rates of ARF were examined in relation to individual factors (age, ethnicity) and area factors based on the CAU of home address (household crowding, New Zealand deprivation index, household income, and proportion of children aged 5–14 years). The multivariate relationship between ARF incidence and CAU-based variables was assessed using a zero-inflated negative binomial model.

Results: This study included 1249 new cases of ARF between 1996 and 2005. At the univariate level, ARF rates were associated with household crowding across all age groups and ethnicities. ARF rates were significantly and positively related to household crowding after controlling for age, ethnicity, household income, and the density of children in the neighborhood. The incidence rate ratio was 1.065 (95% confidence interval, 1.052–1.079) for the total population.

Conclusions: In New Zealand, ARF rates are associated with household crowding at the CAU level. This finding supports action to reduce household crowding to improve health and reduce health inequalities. Our conclusion could be further investigated using a case-control study.