Plastic flow properties and microstructural evolution in an ultrafine-grained Al-Mg-Si alloy at elevated temperatures

An AA6082 alloy was subjected to eight passes of equal channel angular pressing at 100 °C, resulting in an ultrafine grain size of 0.2 to 0.4 µm. The tensile deformation behavior of the material was studied over the temperature range of 100 °C to 350 °C and strain rate range of 10¯⁴ to 10¯¹ s¯¹. The evolution of microstructure under tensile deformation was investigated by analyzing both the deformation relief on the specimen surface and the dislocation structure. While extensive microshear banding was found at the lower temperatures of 100 °C to 150 °C, deformation at higher temperatures was characterized by cooperative grain boundary sliding and the development of a bimodal microstructure. Dislocation glide was identified as the main deformation mechanism within coarse grains, whereas no dislocation activity was apparent in the ultrafine grains.

Towards the optimization of performance of Atlantic salmon reared at different water temperatures via the manipulation of dietary ARA/EPA ratio

In recent years, aquaculture has been facing a series of new issues, including the necessary replacement of fish oil and fish meal because of their limited supply and sub-optimal water temperature conditions. Higher water temperatures are increasingly encountered as the result of climate change related phenomena and/or the practice of farming of species in areas with environmental characteristics outside their optimal physiological range, such as the case of Atlantic salmon (. Salmo salar) farming in Australia during the summer season. Previous studies in teleost fish have shown that when fish are exposed at higher environmental temperatures, fish had a preferential increased dietary intake for arachidonic acid (20:4n - 6, ARA). This observation suggests that, given the several metabolic roles of ARA, its dietary provision may play an important role in fish for adapting at sub-optimal high water temperatures. The objective of this study was therefore to evaluate the effects of different dietary ARA/EPA ratios in juvenile Atlantic salmon as affected by time of exposition to the diet and water temperatures, with particular focus to fish performance and possible resulting modifications of tissue fatty acid composition. The study showed that independently from dietary treatments, fish held at the higher temperatures had an increased ARA accumulation, primarily in the liver and this ARA accumulation increased over time. It was also shown that the combined dietary inclusion of ARA and EPA significantly improved fish performance, compared with diets either richer in ARA or EPA. A general trend toward higher content of n - 3 LC-PUFA at lower temperatures was also quite clear, especially in the liver. Therefore, and assuming that the trends in tissue fatty acid composition could be taken as a clue of the optimal fatty acid requirements of fish, the n - 6 requirement (and in particular ARA) clearly appears to be greater for Atlantic salmon raised at high water temperatures. Protein accumulation was higher in the diet with the combined dietary inclusion of ARA and EPA for fish held at high water temperature (20. °C), with a concomitant lipid reduction. This study shows the importance of dietary ARA for maximal growth in Atlantic salmon, particularly during the period of the year when high water temperatures are often encountered. Further studies specifically looking at optimal dietary ARA/EPA ratio and roles of ARA on myogenesis, stress physiology and immune status of cultured fish are warranted. Statement of relevance: Given the current high level of fish oil replacement in aquafeed, and the often encountered sub-optimal environmental temperatures, we believe that this study could be considered as timely and highly pertinent for the aquaculture industry and associated R&D sector.

Microstructural development during hot working of Mg-3AI-1Zn

he microstructural evolution is examined during the hot compression of magnesium alloy AZ31 for both wrought and as-cast initial microstructures. The influences of strain, temperature, and strain rate on the dynamically recrystallized microstructures are assessed. Both the percentage dynamic recrysallization (DRX) and the dynamically recrystallized grain size were found to be sensitive to the initial microstructure and the applied deformation conditions. Lower Z conditions (lower strain rates and higher temperatures) yield larger dynamically recrystallized grain sizes and increased percentages of DRX, as expected. The rate with which the percentage DRX increases for the as-cast material is considerably lower than for the wrought material. Also, in the as-cast samples, the percentage DRX does not continue to increase toward complete DRX with decreasing Z. These observations may be attributed to the deformation becoming localized in the DRX fraction of the material. Also, the dynamically recrystallized grain size is generally larger in as-cast material than in wrought material, which may be attributed to DRX related to twins and the inhomogeneity of deformation. Orientation maps of the as-cast material (from electron backscattering diffraction (EBSD) data) reveal evidence of discontinuous DRX (DDRX) and DRX related to twins as predominant mechanisms, with some manifestation of continuous DRX (CDRX) and particle-stimulated nucleation (PSN).

Diacylglycerols from butterfat: production by Glycerolysis and short-path diltillation and analysis of physical properties

The aim of this paper was to develop a process for the production of DAG from butterfat through glycerolysis and short-path distillation and to evaluate the physical properties of the DAG in comparison with the original butterfat. Chemical glycerolysis produced a mixture of acylglycerols containing DAG together with MAG and TAG. From the mixture of glycerolysis products, MAG were removed through three consecutive distillations (vacuum <0.001 mbar) at 150°C. TAG were separated from DAG by distillation at 210°C, which gave a product with more than 80% DAG in the distillates. Distillation temperatures had significant effects on acyl migration. The formation of desirable 1,3-DAG was favored at higher temperatures. Under 210°C distillation, the equilibrium ratio of 6∶4 was obtained between 1,3-DAG and 1,2(2,3)-DAG. The FA profile of the DAG product was relatively similar to the original butterfat. The total DAG recovery was around 77% in the pilot-scale production. The different patterns of m.p. were observed between butterfat and the DAG fraction produced as well as the MAG fraction collected. Solid fat content profiles of the DAG fraction and its mixtures with rapeseed oil possessed trends similar to those of the corresponding butterfat and its mixtures with rapeseed oil. Compared with butterfat, the DAG fraction behaved differently in its thermal profiles, crystallization patterns, and rheological properties; for example, the dropping point was 13°C higher for the latter than for the former, and the crystal pattern was mostly β form for the latter, whereas the former was the β′ form.

Substitution reactions of carbon nanotube template

Substitution reactions between carbon nanotube (CNT) template and SiO with the formation of carbon rich silicon oxide nanowires (SiO–C-NWs) have been investigated using transmission electron microscopy and x-ray energy dispersive spectroscopy. The reaction was carried out by thermal annealing at 1200 °C for 1 h of a mixture of silicon monoxide (SiO) and iron (II) phthalocyanine, FeC32N8H16 (FePc) powders. Multiwalled CNTs were produced first via pyrolysis of FePc at a lower temperature (1000 °C). SiO vapors reacted with the CNTs at higher temperatures to produce amorphous SiO–C-NWs with a uniform diameter and a length in tens of micrometers. The special bamboolike structure of the CNTs allows the reaction to start from the external surface of the tubes and transform each CNT into a solid nanowire section by section.

Superhydrophobic modification of polyimide films based on gold-coated porous silver nanostructures and self-assembled monolayers

We present a facile and effective method for controlling the surface hydrophobicity of polyimide films from sticky to superhydrophobic properties by tailoring their topographies. Nanostructured silver layers were produced on polyimide films by treatment with aqueous KOH and AgNO3, followed by thermal treatment at 200 degrees C or higher temperatures. Further modification of the gold-coated silver layers with n-dodecanethiol led to hydrophobic surfaces. Different morphologies of the silver layers at the micro- and nano-meter scales, which result in the variety of hydrophobicity, can be tailored by controlling the thermal treatment temperature. Surfaces prepared at 320 degrees C showed a sticky property that water drops did not slide off even when the sample was held upside down. Superhydrophobic surfaces were obtained when the temperature was above 340 degrees C. A remarkable superhydrophobicity, as evidenced by a very large water contact angle of 162 degrees and a very small sliding angle of 7 degrees, was achieved by heating the modified polyimide films at 360 degrees C. This is also the first example for superhydrophobic modification of polyimide films.

Deformation modes and anisotropy in magnesium alloy AZ31

A strongly textured sheet of magnesium alloy AZ31 has been subjected to tensile testing at temperatures between ambient and 300°C. Structures have been examined by optical and transmission electron microscopy and also by atomic force microscopy to quantify surface displacements seen at grain boundaries. Plastic anisotropy varies strongly with test temperature as was observed previously by Agnew and Duygulu. The present findings do not support the view that crystallographic <c + a> becomes a major contributor to deformation at higher temperatures. Rather, the material behaviour reflects an increasing contribution from grain boundary sliding despite the relatively high strain rate (I 0^-3 s^-1) used in the mechanical tests.

Molecular dynamics simulations of highly concentrated salt solutions : structural and transport effects in polymer electrolytes

Structural, thermodynamic and transport properties have been calculated in concentrated non-aqueous NaI solutions using molecular dynamics simulations. Although the solvent has been represented by a simplistic Stockmayer fluid (spherical particles with point dipoles), the general trends observed are still a useful indication of the behavior of real non-aqueous electrolyte systems. Results indicate that in low dielectric media, significant ion pairing and clustering occurs. Contact ion pairs become more prominent at higher temperatures, independent of the dielectric strength of the solvent. Thermodynamic analysis shows that this temperature behavior is predominantly entropically driven. Calculation of ionic diffusivities and conductivities in the NaI/ether system confirms the clustered nature of the salt, with the conductivities significantly lower than those predicted from the Nernst-Einstein relation. In systems where the solvent-ion interactions increase relative to ion-ion interactions (lower charge or higher solvent dipole moment), less clustering is observed and the transport properties indicate independent motion of the ions, with higher calculated conductivities. The solvent in this system is the most mobile species, in comparison with the polymer electrolytes where the solvent is practically immobile.

N-methyl-N-alkylpyrrolidinium hexafluorophosphate salts : novel molten salts and plastic crystal phases

A new series of salts, based on the N-methyl-N-alkylpyrrolidinium cation and the PF₆- anion, are reported and their thermal properties described for alkyl = Me, Et, Pr, Bu, Hx, and Hp. X-ray structures of several of the salts are also reported. The N,N-dimethylpyrrolidinium hexafluorophosphate has a melting point greater than 390 °C; however, the N-methyl-N-butylpyrrolidinium derivative melts at 70 °C. Most of the PF₆- salts were observed to have lower melting points in comparison with the analogous iodide salts. Most of the salts exhibit one or more thermal transitions prior to melting and a final entropy of melting less than 20 J K^-1 mol^-1, behavior which has previously been associated with the formation of plastic crystal phases. Good crystal structure solutions were obtained at low temperatures in the case of the alkyl = propyl and heptyl derivatives. The loss of diffraction peaks and changes in symmetry at higher temperatures indicated the presence of dynamic rotational disorder, supporting the understanding that the plastic properties arise from rotational motions in the crystal.

Highly concentrated salt solutions : molecular dynamics simulations of structure and transport

Molecular dynamics (MD) simulations in NaI solutions, where the solvent has been represented by the Stockmayer fluid, were performed as a function of temperature, salt concentration, and solvent dipole strength. At higher temperatures contact ion pairs become more prevalent, regardless of solvent strength. An examination of the temperature dependence of the potential of mean force demonstrates the entropic nature of this effect. The transport properties calculated in the simulations are dependent on the balance between solvent dielectric constant and ion charge. In systems with a large solvent dipole moment, the ions appear to be independently mobile, and deviations from Nernst–Einstein behavior are small. In systems of smaller solvent dipole moment or greater ion charge, the ions form clusters, and large deviations from Nernst–Einstein behavior are observed.

Balancing comfort expectations and greenhouse gas emissions, thermal comfort in office buildings in a changing climate

According to the Fourth Assessment Report of the Intergovernmental Panel on Climate Change (IPCC), the construction sector has the greatest potential for climate change mitigation. This work investigates the potential for climate change mitigation in naturally ventilated and mixed mode office buildings, by evaluating the range of influence of building design and occupants on greenhouse gas emissions as well as thermal and visual comfort.

Thermal comfort is evaluated according to the EN 15251 adaptive thermal comfort model, visual comfort is based on daylight autonomy and view. Parametric studies have been conducted based on building simulation for the climate of Athens, Greece. Input data are based on a literature review, and on results from a field study conducted among office occupants and architects in Athens.

The results show that the influence of occupants on greenhouse gas emissions is larger than the influence of building design. Energy saving office equipment, as well as active use of building controls for shading and lighting by occupants are crucial parameters regarding the reduction of CO2 emissions. In mixed mode buildings, the coefficient of performance of the cooling system is an important parameter as well. Regarding thermal and visual comfort, the influence of building design is predominant. A green building, well protected against heat from the sun and able to balance solar and internal heat gains, provides higher comfort levels and is less affected by the influence of occupants. In mixed mode buildings, building design is the predominant influence on the magnitude of cooling loads. A hot summer including heat waves can significantly reduce thermal comfort and increase the resulting greenhouse gas emissions. Green buildings are least affected by these influences.

The EN 15251 adaptive thermal comfort model provides a thermal comfort evaluation method valid throughout Europe. However, for the Mediterranean climate of Athens, Greece, most of the configurations investigated within this study do not meet the requirements according to this model. EN 15251 refers to an adaptive thermal comfort model for naturally ventilated and to a static model for mechanically ventilated buildings. For mixed mode buildings, the static model is recommended, but literature indicates that occupants in those buildings might be more tolerant towards higher temperatures. The hypothetical application of the EN 15251 adaptive thermal comfort model in mixed mode offices, as investigated in this study, shows potential for greenhouse gas emission savings. However, this influence is small compared to that of building design and occupants. Conclusions are drawn regarding the categorisation and exceeding criteria according to EN 15251 adaptive thermal comfort model for offices in a Mediterranean climate.

The results of this work show, that not only green buildings, but also green occupants can significantly contribute to the mitigation of the climate change. Mechanisms of the real estate market as well as the lifestyle of occupants are important influences in this context. Sustainability therefore refers to finding the right balance between occupant’s comfort expectations and resulting greenhouse gas emissions for a specific building, rather than optimisation of single parameters

Structure effect on the oxygen permeation properties of barium bismuth iron oxide membranes

In this work, we investigated the oxygen permeation properties of barium bismuth iron oxide within the family of [Ba_2−3xBi_3x−1][Fe_2xBi_1−2x]O_2+3x/2 for x = 0.17–0.60. The structure changed progressively from cubic to tetragonal and then to hexagonal as function of x in accordance with the different relative amounts of bismuth on A-site and B-site of ABO_3−δ perovskite lattices. We found that the oxygen flux and electrical conductivity correlated strongly, and it was prevalent for the cubic structure (x = 0.33–0.40) which conferred the highest oxygen flux of 0.59 ml min⁻¹ cm⁻² at 950 °C for a disk membrane x = 0.33 with a thickness of 1.2 mm. By reducing the thickness of the disk membrane to 0.8 mm, the oxygen flux increased to 0.77 ml min⁻¹ cm⁻², suggesting both surface kinetics and ion diffusion controlled oxygen flux, though the former was more prominent at higher temperatures. For disk membranes x = 0.45–0.60, the perovskite structure changed to tetragonal and hexagonal, and the oxygen flux was insignificant below 900 °C, clearly indicating electron conduction properties only. However, for two compositions with relatively high bismuth content, e.g. x = 0.55 and 0.60, there was a sudden and significant rise of oxygen permeability above 900 °C, by more than one order of magnitude. These materials changed conduction behavior from metallic to semiconductor at around 900 °C. These results suggest the advent of mixed ionic electronic conducting properties caused by the structure transition as bismuth ions changed their valence states to compensate for the oxygen vacancies formed within the perovskite lattices.

Factors influencing the winter haulout behaviour of Weddell seals : consequences for satellite telemetry

An understanding of pinniped haulout behaviour can provide information on how animals interact with their environment, their foraging strategies and the behaviour of their prey. For Weddell seals Leptonychotes weddelli, knowledge of haulout patterns and the environmental drivers of haulout is comprehensive for the austral spring and summer, but is poorly described outside this period. Pinniped behaviour is commonly examined using satellite telemetry; however, it is unclear whether the behavioural state of the seal can itself influence data acquisition. We examined haulout behaviour of female Weddell seals in eastern Antarctica over 3 winters (March to August, 2006–2008) using satellite-linked data loggers. Haulout behaviour followed a diel cycle with predominantly nocturnal haulouts. The environmental variables wind speed and temperature were influential on haulout, with seals tending to haul out more in lower winds and at higher temperatures. Haulout duration decreased across the winter, as did the number of satellite uplinks, suggesting that haulout duration played a role in data acquisition. There was no evidence of a decline in tag condition over this period, indicating that the decrease in uplinks was primarily the result of the winter behaviour of the seals. Overall, the number of haulout locations in the data set was over-represented, with more uplinks per hour occurring when the seals were hauled out than when they were at sea. For Weddell seals and other ice seals, tracking data that include haulout locations can bias spatial representations of foraging behaviour (e.g. haulout sites may be mistaken for regions of area-restricted search).

Parasitized snails take the heat : a case of host manipulation?

Infection-induced changes in a host’s thermal physiology can represent (1) a generalized host response to infection, (2) a pathological side-effect of infection, or (3), provided the parasite’s development is temperature-dependent, a subtle case of host manipulation. This study investigates parasite-induced changes in the thermal biology of a first intermediate host infected by two castrating trematodes (genera Maritrema and Philophthalmus) using laboratory experiments and Weld surveys. The heat tolerance and temperatures selected by the snail, Zeacumantus subcarinatus, displayed alterations upon infection that differed between the two trematodes. Upon heating, snails infected by Maritrema sustained activity for longer durations than uninfected snails, followed by a more rapid recovery, and selected higher temperatures in a thermal gradient. These snails were also relatively abundant in high shore localities in the summer only, corresponding with seasonal elevated microhabitat temperatures. By contrast, Philophthalmus infected snails fell rapidly into a coma upon heating and did not display altered thermal preferences. The respective heat tolerance of each trematode corresponded with the thermal responses induced in the snail: Maritrema survived exposure to 40°C, while Philophthalmus was less heat tolerant. Although both trematodes infect the same tissues, Philophthalmus leads to a reduction in the host’s thermal tolerance, a response consistent with a pathological side effect. By contrast, Maritrema induces heat tolerance in the snail and withstood exposure to high heat. As the developmental rate and infectivity of Maritrema increase with temperature up to 25°C, one adaptive explanation for our findings is that Maritrema manipulates the snail’s thermal responses to exploit warm microhabitats.

Morphology evolution during annealing and electrical conductivity of titania nanotube films

Titania nanotube films were produced by anodization of titanium foil. The titania nanotube films were annealed at different temperatures. Morphology evolution, phase transformation and electrical conductivity of the titania nanotubes were studied. Results showed that the nanotube walls became rough, porous and even collapsed after annealed at 400, 500 and 600°C respectively. Titania anatase phase formed after annealed at 400°C; the amount of anatase phase increased as the annealing temperature increased. The conductivity of the nanotube film annealed at 400°C was improved greatly compared with the conductivity of the as-anodized nanotube film. However, the conductivity of the nanotube films annealed at higher temperatures decreased. The effect of the morphology on the electronic conductivity of the titania nanotube films was discussed.