Performance of ventilated hollow core concrete panel systems in Australia

Performance of advanced fabric energy storage systems has not been reported for Australian conditions. The influence pf slab thickness and air flow rate on the annual thermal load, and maximum heating and cooling demands for a typical office module using a ventilated hollow core concrete slab system has been investigated by simulation. Performance results for Melbourne are presented and comments made on other locations.

The effect of artificial defects on the compressive properties of hollow sphere cellular aluminium (HSCA)

Hollow sphere cellular aluminium (HSCA) samples were fabricated by bonding together two kinds of single aluminium hollow spheres with the same outside diameter of 4 mm but different wall thicknesses of 0.1 mm and 0.3 mm, in which the hollow spheres with the thinner sphere wall thickness were used as artificial defects. Four types of HSCA samples with the same relative density but various distributions of artificial defects were prepared by simple cubic packing. For comparing, HSCA sample without defective hollow spheres inside was also prepared. The effects of the distribution of the artificial defects on the deformation behaviours and mechanical properties were investigated by compressive tests. Results indicated that the nominal stress - nominal strain curve and the deformation behavior of the HSCA samples varied with the distribution of the artificial defects in spite of the same relative density. It is therefore suggested that the deformation behavior and mechanical property of cellular materials were also significantly affected by the distribution of defects. In particular, the plateau stress of the HSCA samples increased with the decrease in number of contact points between the normal hollow spheres and the defective hollow spheres in the loading direction during deformation.

Compressive properties and energy absorption of hollow sphere aluminium

Manufactured cellular aluminums have been developed for a wide range of automotive applications where weight savings, improved safety, crashworthiness and comfort are required. The plateau deformation behavior of cellular aluminums under compressive loading makes this new class of lightweight materials suitable for energy absorption and comes close to ideal impact absorbers. In the present study, aluminum hollow hemispheres were firstly processed by pressing. Hollow sphere aluminum samples with a body-centered cubic (BCC) packing were then fabricated by bonding together single hollow spheres, which were prepared by adhering together hollow hemispheres. Hollow sphere aluminum samples with various kinds of sphere wall thicknesses of 0.1 mm, 0.3 mm and 0.5 mm but the same outside diameter of 4 mm were investigated by compressive tests. The effects of the sphere wall thickness on the mechanical properties and energy absorption characteristics were investigated.

Processing and mechanical properties of hollow sphere aluminum foams

Hollow sphere metallic foams are a new class of cellular material that possesses the attractive advantages of uniform cell size distribution and regular cell shape. These result in more predictable physical and mechanical properties than those of cellular materials with a random cell size distribution and irregular cell shapes. In the present study, single aluminum hollow spheres with three kinds of sphere wall thickness as 0.1 mm, 0.3 mm and 0.5 mm were processed by a new pressing method. Hollow sphere aluminum foam samples were prepared by bonding together single hollow spheres with simple cubic packing (SC) and body-centered cubic packing (BCC). Compressive tests were carried out to evaluate the deformation behaviors and mechanical properties of the hollow sphere aluminum foams. Effects of the sphere wall thickness and packing style on the mechanical properties were investigated.

Hollow avowals of human rights protection-time for an Australian federal bill of rights?

Unlike the constitutions of many nations, such as the United States of America and the Republic of South Africa, the constitutions of the Australian States and Territories and the Commonwealth Constitution Act 1901 (UK) contain no bill of rights. Australia is the only western democracy without a federal bill of rights. The debate regarding the need for a bill of rights necessitates an understanding of what human rights the people of Australia already enjoy. If sufficient protection can be found in existing sources, does Australia really need a federal bill of rights? Opponents of a bill of rights state that we have sufficient protection from arbitrary government intervention in our personal affairs and thus a bill of rights is unnecessary. There are a number of potential sources of human rights in Australia that might provide the suggested existing protection, including the common law, specific domestic legislation, international law and constitutional law. Each of these sources of human rights has, however, important limitations. The focus of this article is on the inadequacy of the Australian constitutions as a source of purported protection. This in turn suggests that an alternative source of rights is needed - a federal bill of rights? In the course of this analysis the author makes suggestions for reform; specifically how a federal bill of rights may address the paucity of constitutional protection.

Enhanced oxygen permeation through perovskite hollow fibre membranes by methane activation

Hollow fibre membranes of mixed conducting perovskite La_0.6Sr_0.4Co_0.2Fe_0.8O₃ (LSCF) were prepared via the combined phase inversion and sintering technique. The fibres were tested for air separation with a home-made reactor under the oxygen partial pressure gradient generated by the air/He streams. Some fibres were in situ activated by introducing methane in the He sweeping gas at high temperatures. The activated membranes with new morphology were created by transforming the inner densified surface layer to a porous structure. Compared to the original membranes, the activated gave appreciable higher oxygen fluxes. At 800 °C, the oxygen fluxes were increased by a factor of 10 after activation was carried out at 1000 °C for 1 h.

High performance BaBiScCo hollow fibre membranes for oxygen transport

Here we report the production of novel high performance BaBi_0.05Sc_0.1Co_0.85O_3-3 (BaBiScCo) hollow fibres delivering oxygen fluxes of 11.4 ml cm^-2 min^-1 at 950 °C. The doping of bismuth, a highly ionic conductor, at the B-site of a barium based perovskite overcame oxygen ionic transport limitations even at temperatures as low as 600 °C.

Optimizing oxygen transport through La0.6Sr0.4Co0.2Fe0.8O3-δ hollow fiber by microstructure modification and Ag/Pt catalyst deposition

This work compares the oxygen permeation fluxes of five different La0.6Sr0.4Co0.2Fe0.8O3−δ membranes (e.g. disk, conventional hollow fiber, modified hollow fiber, Ag- or Pt-deposited hollow fiber membranes) to elucidate the dominance of a particular oxygen transport limiting step (e.g., bulk-diffusion or surface reaction) within each of these membranes. At 900 °C and 100 mL min–1 helium gas sweep rate, the oxygen fluxes for disk, conventional hollow fiber, modified hollow fiber, Ag-deposited modified hollow fiber, and Pt-deposited modified hollow fiber membranes are 0.10, 0.33, 0.84, 1.42, and 2.62 mL min–1 cm–2, respectively, denoting enhanced performance in this sequential order. More than 300% enhancement of fluxes is evidenced by modifying the geometry from disk to conventional hollow fiber. This is attributed to the thickness reduction from 1 mm to 0.3 mm, thus implying bulk-diffusion and surface reaction as the jointly limiting transport step for this disk membrane. In contrast to a conventional hollow fiber that has a sandwich cross-sectional structure (e.g. dense center layer sandwiched by two finger-like layers) as well as dense outer and inner circumference surfaces, the modified hollow fiber has only one dense layer in its outer circumference surface with finger-like porous layer extending all the way from outer cross-sectional part to the inner cross-sectional part. This microstructural difference, in turn, provides substantial reduction of membrane thickness and enlarges surface reaction area for modified hollow fiber (relative to conventional hollow fiber), both of which contributes to the reduced bulk-diffusion and surface reaction resistance; evidenced by almost 250% oxygen flux enhancement. To enhance the performance even further, catalyst (e.g., Ag or Pt) deposition on the outer circumference surface of modified hollow fiber can be utilized to reduce its dominating surface reaction resistance. While both catalysts increase the oxygen fluxes, Pt reveals itself as the better candidate relative to Ag due to melting-induced aggregation and growth of Ag at 950 °C.