Effective grain orientation on the substructure development of 304 stainless steel and NA-30% fe

This data is the result of an investigation into the effect of grain orientation on the substructure development of 304 stainless steel and a Ni-30wt.%Fe alloy. Both alloys have been used as model alloys to study the high temperature deformation of austenite. The development of the dislocation substructure as a function of strain, temperature and grain orientation was investigated using a combination of electron backscatterd diffraction (EBSD) and transmission electron microscopy (TEM).

Temperature and grain orientation dependence of mechanical twinning in a high manganese TWIP steel

 This thesis contains fundamental studies of the deformation mechanisms of the third generation steel at different deformation temperatures. To analyse the microstructure of the steel a unique characterisation technique was implemented for the first time. These analyses provided with vital parameters for modelling the stress-strain behaviour of the steel at different deformation temperatures.

Automatic grain texture analysis using integral transforms

Tonewood for musical instruments is quarter-sawn and frequently quality-graded based on visual appearance, mechanical and acoustic properties. The assessment uses simple human (subjective) observation, and two ‘‘experts’’ can rate the same sample differently. This paper describes the application of integral transforms (Fourier and Radon) for automatic (objective) assessment of the visual appearance of 10 Sitka spruce (Picea sitchensis) sample images. This work considers surface classification on the basis of grain orientation, count, spacing, and evenness or uniformity.

Orientation dependence of the deformation microstructure in a Fe-30Ni-Nb model austenitic steel subjected to hot uniaxial compression

The present work was aimed at a detailed investigation of the orientation dependence of the microstructure characteristics in a Fe-30Ni-Nb austenitic model steel subjected to hot uniaxial compression at 1198 K (925 °C) at a strain rate of 1 s−1 to several strain levels up to 1.0. The quantification of the substructure evolution as a function of strain was performed for the stable 〈011〉 oriented grains. Other grain orientations were also investigated in detail at a strain of 0.2. The 〈110〉 oriented grains contained self-screening arrays of “microbands” (MBs) aligned with high Schmid factor {111} slip planes. The MB crystallographic alignment was largely maintained up to a strain of 1.0, which suggests that the corresponding boundaries kept continuously rearranging themselves during straining and did not follow the sample shape change. The mean MB spacing decreased and misorientation angle increased with strain towards saturation, indicating the operation of the “repolygonization” dynamic recovery mechanism. The non-〈011〉 oriented grains displayed a strong tendency to split during deformation into deformation bands having alternating orientations and being mutually rotated by large angles. The bands were separated by transition regions comprising arrays of closely spaced, extended sub-boundaries collectively accommodating large misorientations across very small distances.

Microstructural modeling of dynamic recrystallization using irregular cellular automata

Cellular automaton (CA) was used to simulate dynamic recrystallization (DRX) during thermomechanical deformation. Initial grain size, initial grain orientation and dislocation density were used as input data to the CA model. Flow curve, dislocation density, final grain size and orientation, and DRX volume fraction were the output data which were compared with experimental data to validate the model. The model proposed in this work considered the thermomechanical parameters (e.g., temperature and strain rate) and their role on the nucleation and growth kinetics during DRX. It was shown that the CA model can predict the final microstructure and flow curve to a high degree of accuracy and was able to successfully simulate the volume fraction of DRX as a function of strain for a wide range of deformation conditions.

Texture and substructure characteristics of dynamic recrystallization in a Ni–30%Fe austenitic model alloy

The substructure and texture development during dynamic recrystallization (DRX) of an austenitic Ni–30%Fe model alloy was investigated using hot torsion testing. The current results revealed that the DRX texture was dominated by grains with a low Taylor factor component. This was related to the preferred nucleation and lower consumption rates of these grains during DRX. The substructure of DRX grains was ‘‘random” in character and displayed complex subgrain/cell arrangements that largely depended on grain orientation.

EBSD and TEM investigation of the hot deformation substructure characteristics of a type 316L austenitic stainless steel

The evolution of crystallographic texture and deformation substructure was studied in a type 316L austenitic stainless steel, deformed in rolling at 900 °C to true strain levels of about 0.3 and 0.7. Electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) were used in the investigation and a comparison of the substructural characteristics obtained by these techniques was made. At the lower strain level, the deformation substructure observed by EBSD appeared to be rather poorly developed. There was considerable evidence of a rotation of the pre-existing twin boundaries from their original orientation relationship, as well as the formation of highly distorted grain boundary regions. In TEM, at this strain level, the substructure was more clearly revealed, although it appeared rather inhomogeneously developed from grain to grain. The subgrains were frequently elongated and their boundaries often approximated to traces of {111} slip planes. The corresponding misorientations were small and largely displayed a non-cumulative character. At the larger strain, the substructure within most grains became well developed and the corresponding misorientations increased. This resulted in better detection of sub-boundaries by EBSD, although the percentage of indexing slightly decreased. TEM revealed splitting of some sub-boundaries to form fine microbands, as well as the localized formation of microshear bands. The substructural characteristics observed by EBSD, in particular at the larger strain, generally appeared to compare well with those obtained using TEM. With increased strain level, the mean subgrain size became finer, the corresponding mean misorientation angle increased and both these characteristics became less dependent on a particular grain orientation. The statistically representative data obtained will assist in the development of physically based models of microstructural evolution during thermomechanical processing of austenitic stainless steels.

Finite element simulations of the cyclic elastoplastic behaviour of copper thin films

A large-scale computational and statistical strategy is presented to investigate the development of plastic strain heterogeneities and plasticity induced roughness at the free surface in multicrystalline films subjected to cyclic loading conditions, based on continuum crystal plasticity theory. The distribution of plastic strain in the grains and its evolution during cyclic straining are computed using the finite element method in films with different ratios of in-plane grain size and thickness, and as a function of grain orientation (grains with a {1 1 1} or a {0 0 1} plane parallel to the free surface and random orientations). Computations are made for 10 different realizations of aggregates containing 50 grains and one large aggregate with 225 grains. It is shown that overall cyclic hardening is accompanied by a significant increase in strain dispersion. The case of free-standing films is also addressed for comparison. The overall surface roughness is shown to saturate within 10 to 15 cycles. Plasticity induced roughness is due to the higher deformation of {0 0 1} and random grains and due to the sinking or rising at some grain boundaries.

Contribution of twinning to low strain deformation in a Mg alloy

Deformation twinning plays an important role in the yielding of extruded magnesium alloys, especially when loaded in compression along the extrusion axis. The magnitude of this contribution is not accurately known. The present study employs electron backscatter diffraction to reveal the influence of grain orientation on twin-volume fraction for alloy AZ31 tested in compression to strains between 0.008 and 0.015. For these strains, it is seen that approximately 45 pct of the deformation can be attributed to "tensile" twinning. The variation of twin-volume fraction over different orientation classes correlates closely with the maximum Schmid factors for both tensile twinning and basal slip. These effects are readily explained quantitatively using a mean field crystal plasticity model without recourse to stochastic effects. Encouraged by this, we introduce an analytical approximation based on the uniformity of (axial) work. © 2013 The Minerals, Metals & Materials Society and ASM International.

The evolution of microbands and their interaction with NbC precipitates during hot deformation of a Fe-30Ni-Nb model austenitic steel

The present work has investigated the evolution of microbands (MBs) and their interaction with strain-induced NbC precipitates during uniaxial compression of a model austenitic Fe-30Ni-Nb steel at 925 °C. The (1 1 0) fibre grains, both without and with copious amounts of precipitates, contained up to large strains crystallographic MBs aligned close to the highly stressed {1 1 1} slip planes having large Schmid factors. The MBs thus maintained their crystallographic character during straining, through continuously rearranging themselves, and did not follow the macroscopically imposed rigid body rotation. During double-pass deformation, fine NbC particles formed at short inter-pass holding remained strongly pinned at small reloading strains and appeared to be dragged by rearranging MB walls. With increasing reloading strain, the fine precipitates became progressively released from the above walls. During reloading after increased holding time, the coarsened particles tended with their increased size to become increasingly detached from the MB walls already at a small strain. The precipitate-free MB wall segments rearranged during straining to maintain their crystallographic alignment, while the detached precipitates followed the sample shape change and rotated towards the compression plane. The MB wall rearrangement generally occurred through cooperative migration of the corresponding dislocation networks.

New insights into the mechanism of low-temperature active-screen plasma nitriding of austenitic stainless steel

Low-temperature active-screen plasma nitriding is an effective surface engineering technology to improve the wear and corrosion resistance of austenitic stainless steel through the formation of expanded austenite. The material sputtered from the active screen and redeposited on the specimens has been suggested to play an important role in the nitriding mechanism involved. This paper reports a patterned deposition layer, which is in correlation with the grain orientation of polycrystalline specimens. This has provided new insights into the nitriding mechanism. © 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Modelling the combined effect of grain size and grain shape on plastic anisotropy of metals

Within each columnar grain of a metallic film, the resistance to dislocation glide varies in function of the orientation of the slip plane with regard to the grain long axis. Plastic slip is impeded across grain boundaries and this contributes to the anisotropy of the overall mechanical response. A simplified (Taylor-type) crystal plasticity model is proposed that accounts for such effect of grain shape on the slip system selection. Assuming that dislocation density gradients are normal to the grain boundaries, backstresses developed at the onset of plasticity are estimated based on two definitions of the effective grain boundary spacing ‘‘seen’’ by individual slip systems. The first one reduces to the mean area-to-perimeter ratio of cross-sections of the grain cut parallel to the slip plane. Closed-form expressions of the average backstresses developed inside grains with spheroidal shapes are introduced in the crystal hardening law. The model reproduces the very high plastic anisotropy of electro-deposited pure iron with a strong c-fiber and a refined columnar grain structure [Yoshinaga, N., Sugiura, N., Hiwatashi, S., Ushioda, K., Kada, O., 2008. Deep drawability of electro-deposited pure iron having an extremely sharp h111i//ND texture. ISIJ Int. 48, 667–670]. It also provides valid estimates of the texture development and the influence of grain size on the yield strength.

Development of boundary misorientations during grain growth in silicon steels

Changes in grain size, texture and misorientation distributions have been monitored during extensive normal grain growth in 3%Si steels. The boundary misorientation distributions deviate significantly from the Mackenzie relationship. Comparisons of correlated and uncorrelated distributions show large excesses of low angle boundaries. However, these are not a result of low energy boundaries being favoured during grain growth since the deviation diminishes as growth proceeds. The effect originates in the nucleation of grains in colonies of similar orientation during primary recrystallisation. A slight tendency for promotion of 60º boundaries may indicate some preference for the retention of lower energy twin boundaries during grain growth in silicon steel.

Orientation dependence of the substructure characteristics in a Ni- 30%Fe austenitic alloy deformed in hot torsion

The present work examines the microstructure and texture evolution in a Ni-30wt.%Fe austenitic model alloy deformed in torsion at 1000 °C, with a particular emphasis on the orientation dependence of the substructure characteristics within the deformed original grains. Texture of these grains was principally consistent with that expected for simple shear and comprised the main A, B and C components. The deformation substructure within the main texture component grains was characterised by "organised" arrays of parallel microbands with systematically alternating misorientations, locally accompanied by micro-shear bands within the C grains. With increasing strain, the mean subgrain size gradually decreased and the mean misorientation angle concurrently increased towards the saturation. The stored deformation energy within the main texture component grains was principally consistent with the respective Taylor factor values. The microband boundaries corresponded to the expected single slip {111} plane for the A oriented grains while these boundaries for the C oriented grains represented a variety of planes even for a single grain.